Search

In France, deep geological disposal is considered for the storage of high and intermediate‐level long‐lived radioactive wastes. For aluminium, the possibility to encapsulate the wastes in a cement‐based matrix is studied. However, cement being an alkaline environment, aluminium can lose its passivity, starts to corrode leading to hydrogen evolution in the infrastructures and generate a possible explosive hazard after decades of storage if hydrogen can accumulate somewhere in the facility. It is therefore necessary to study the corrosion behaviour of aluminium in the different cements considered for the encapsulation to estimate the possible amount of hydrogen that could be generated through corrosion and design the cement capsules accordingly. This work mainly focused on the reaction occurring at the aluminium‐cement interface. Raman spectroscopy did not highlight significant differences in the nature of the corrosion products forming at the cement/aluminium interface, leading to the conclusion that it is not the chemistry of the cement that is the key factor controlling the corrosion rate but rather the physical properties of the cement matrix. [ABSTRACT FROM AUTHOR]

Depending on the lifetime and level of radioactivity of radioactive wastes, different disposal facilities are considered. Though low‐ and intermediate‐level short‐lived waste can be disposed in surface disposal facilities, deep geological disposal is considered for high‐ and intermediate‐level long‐lived waste. In France and Belgium, long‐term disposal is studied in clay host rock media. For aluminum, the disposal concept is based on encapsulation of the waste in a cement‐based matrix. It is also well‐known that aluminum is prone to severe corrosion in sufficiently alkaline environments leading to possible hydrogen production. To ensure the safety of the disposal facilities and the integrity of the cement capsules, the amount of aluminum that is disposed in each waste package must be specified and is limited to mitigate the level of hydrogen production by aluminum corrosion. In the present study, the corrosion resistance of an aluminum alloy (grade EN‐AW‐5754/H111) in two different cement matrices was studied in different configurations at room temperature. In each case, the evolution of hydrogen production was monitored to address the corrosion rate variation versus time. [ABSTRACT FROM AUTHOR]

Abstract: Investigations were carried out in order to formulate and characterize low-alkalinity and low-heat cements which would be compatible with an underground waste repository environment. Several systems comprising Ordinary Portland Cement (OPC), a fast-reacting pozzolan (silica fume (SF) or metakaolin (MK)) and, in some cases, a slow-reacting product (fly ash (FA) or blastfurnace slag (BFS)) were compared. Promising results were obtained with some binary mixtures of OPC and SF, and with some ternary blends of OPC, SF and FA or BFS: pH of water in equilibrium with the fully hydrated cements dropped below 11. Dependence of the properties of standard mortars on the high contents of FA and SF in the low-pH blends was examined. Combining SF and FA seemed attractive since SF compensated for the low reactivity of FA, while FA allowed to reduce the water demand, and dimensional variations of the mortars. Finally, low-heat (ΔT <20 °C under semi-adiabatic conditions) and high strength (≈70–80 MPa) concretes were prepared from two low-pH cements: a binary blend made from 60% of OPC and 40% of SF, and a ternary blend including 37.5% OPC, 32.5% SF and 30% FA. [Copyright &y& Elsevier]

Concrete shrinkage and creep under variable hydric conditions are important factors for the safety and durability of concrete especially in nuclear reactor or nuclear waste storage background. A large (and long – more than 900 days) experimental campaign, conducted on two different concretes, has therefore been designed to study the strains of non loaded and loaded concretes submitted to drying and liquid water imbibition cycles. For the purposes of comparison, concrete strains and mass variations during drying only (50% RH) and/or following cycles of drying/rewetting were also recorded. This allowed the identification of desiccation shrinkage, basic creep and drying creep at 10 MPa of axial stress. Important results were found and have shown that the final mass and strain are not deeply modified by the introduction of a rewetting phase either for a loaded or a non loaded material. [ABSTRACT FROM AUTHOR]