Search

In this paper, a voltage sensorless controller is developed for a two-switch single-phase rectifier that involves power factor correction and active pulsating power buffering without electrolytic capacitors. While a two-switch rectifier normally requires four sensed signals for control, only one current sensor is required in this proposal, thereby offering advantages such as low cost, high compactness, isolation between control and power circuits, and improved reliability. While the basic operating principle follows that of a conventional voltage sensorless controller for single-switch converters, several critical design considerations are the key to the success of the implementation which is explained in detail. The feasibilities of the controller are experimentally testified with a 100-W rectifier prototype regarding both steady state and dynamic performance. [ABSTRACT FROM AUTHOR]

Active pulsating power buffering (PPB) is an effective technique to reduce the energy storage requirement of a single-phase power-factor-correction (PFC) rectifier. Existing single-phase solutions with active PPB, however, generally suffer from high voltage stresses, leading to increased power losses as well as the need for high-voltage-rating semiconductor switches. Previous works have been focusing on two-level switching converter configurations, and thus have failed to address the high-voltage-stress problem. In this paper, a single-phase three-level flying-capacitor PFC rectifier with PPB-embedded switching is proposed. The flying capacitor not only clamps the voltage stresses of all power devices but also functions as a PPB capacitor. The operating principles, control methods, and design guidelines are detailed and the feasibility of the proposed converter is verified through a 48-W (48-V/1-A) hardware prototype. The proposed rectifier is shown to achieve nearly 50% reduction of the voltage stresses, 72% reduction of the buffering capacitor's volume, and 23.8% reduction of the magnetic core size, as compared to a state-of-the-art two-level solution recently proposed. This new approach of formulating single-phase PFC rectifiers with active PPB could dramatically boost the system's efficiency and power density whilst reducing cost. [ABSTRACT FROM AUTHOR]

A component-minimized and low-voltage-stress single-phase power factor correction rectifier without electrolytic capacitor is proposed in this paper. Component minimization is achieved by embedding an active pulsating-power-buffering (PPB) function within each switching period, such that typical add-on power electronic circuits for PPB are no longer needed. Additionally, with a three-level flying-capacitor configuration, the voltage stresses of switching devices can be reduced more than 50% as compared to existing solutions that are based on embedded PPB. The relationship between the inductance requirement and the patterns of the modulation carriers, and how it can be utilized to minimize the magnetics of the rectifier, is also discussed. A 110 W hardware prototype is designed and tested to demonstrate the feasibilities of the proposed rectifier. An input power factor of more than 0.97, peak efficiency of 95.1%, and an output voltage ripple of less than 4.3% across a wide load range have been experimentally obtained. [ABSTRACT FROM AUTHOR]

Active pulsating power buffering (PPB) function can effectively reduce the twice-line frequency energy storage requirement in a single-phase rectifier. Existing single-phase solutions with active PPB must utilize more than two active switches in their circuits. Compared with conventional single-active-switch solutions without active PPB (e.g., a boost power-factor-correction (PFC) rectifier), the cost of additional semiconductor switches and gate drive circuitry in an active PPB-based rectifier may not be justified for low-power applications. This paper presents a family of single-switch single-phase rectifier with active PPB. Taking advantage of the on-time and off-time of a single switch, the proposed rectifiers are formulated by merging two converters that are duty and frequency controlled. The steady-state characteristics of these converters are analyzed. A step-by-step design procedure is provided, and an active control method for limiting the maximum switching frequency for wide-load-range operation is presented. A 100-W prototype is built for the demonstration of the proposed single-switch rectifier concept. It is envisaged that this concept, when combined with other circuit formulation techniques, e.g., partial power processing, dc-voltage feedback, may lead to new derivatives of single-switch rectifiers with more advanced features. [ABSTRACT FROM AUTHOR]

Conventional single-phase power-factor-correction (PFC) rectifiers with active power decoupling capability typically require more than three active switches in their circuits. By exploring the concept of power-buffer cell, a new single-stage PFC rectifier with two active switches, one inductor and one small power-buffering capacitor is reported in this paper. The proposed converter can achieve high-power factor, wide output voltage range, and power decoupling function without using electrolytic capacitor. Additionally, an automatic power decoupling control scheme that is simple and easy to implement is proposed in this paper. The operating principle, control method, and design considerations of the proposed rectifier are also provided. A 100-W prototype with ac input voltage of 110 Vrms and a regulated dc output voltage ranging from 30 to 100 V has been successfully designed and practically tested. The experimental results show that with only a 15 μF power-buffering film capacitor, the proposed converter can achieve an input power factor of over 0.98, peak efficiency of 93.9%, and output voltage ripple of less than 3%, at 100-W output power. [ABSTRACT FROM PUBLISHER]