Search

In this study, we report on the synthesis and evaluation of a sodium, magnesium, and aluminum (Na-Mg-Al) layered double hydroxide (LDH) based sorbent for hydrogen chloride (HCl) removal at concentrations found in lignocellulosic biomass derived syngas. The LDH was synthesized by a spontaneous self-assembly method and further calcined at 700 °C to produce a mixed metal oxide sorbent that we evaluated in the hot gas cleanup of hydrogen chloride at 100 parts per million. The performance of this sorbent was evaluated in a fixed bed reactor from 400 to 600 °C against that of a commercial magnesium and aluminum LDH (ComLDH) material that does not contain sodium in the matrix as well as two other commercial sorbents, sodium carbonate (Na2CO3) and sodium aluminate (NaAlO2). Our Na-Mg-Al LDH is thermally stable in the hot gas cleanup temperature range. During fixed bed experiments, our calcined LDH mixed metal oxide was effective in reducing hydrogen chloride’s concentration below the breakthrough concentration of 1 ppm from 400 to 600 °C for more than 14 h. The better performance of our calcined LDH compared to calcined commercial LDH supported our hypothesis that sodium incorporation in the LDH matrix enhances HCl sorption. Based on comparison against the commercial Na-based sorbents, the following rankings by temperature observed: LDH > NaAlO2 > Na2CO3 at 400 °C; LDH = NaAlO2 > Na2CO3 at 500 °C; and Na2CO3 = NaAlO2 = LDH at 600 °C.

In this study, we evaluated the pelleting characteristics of southern yellow pine (SYP), switchgrass (SG), and their blends for thermochemical conversion processes, such as pyrolysis and gasification. Using a pilot-scale ring-die pellet mill, we specifically assessed the impact of blend moisture, length-to-diameter (L/D) ratio in the pellet die, and ratio of pine to SG on the physico-chemical properties of the resulting pellets. We found that an increase in pine content by 25–50% marginally affected the bulk density; however, it also led to an increase in calorific value by 7% and a decrease in ash content by 72%. A moisture content of 25% (wet basis) and an L/D ratio of 5 resulted in poor pellet durability at 3, but increasing the L/D ratio to 9 and lowering the moisture content to 20% (w.b.) improved the pellet durability to >90% and the bulk density to >500 kg/m3. Blends with ≥50% pine content resulted in lower energy consumption, while a lower L/D ratio resulted in higher pelleting energy. Based on these findings, we successfully demonstrated the high-moisture pelleting of 2.5 ton of pine top residues blended with SG at 60:40 and 50:50 ratios. The quality of the pellets was monitored off-line and at-line by near infrared (NIR) spectroscopy. Multivariate models constructed by combining the NIR data and the pelleting process variables could successfully predict the pine content (R2 = 0.99), higher heating value (R2 = 0.98), ash (R2 = 0.95), durability (R2 = 0.94), and bulk density (R2 = 0.86) of the pellets. Thus, we established how blending and densification of SYP and SG biomass could improve feedstock specifications and that NIR spectroscopy can effectively monitor the pellet properties during the high-moisture pelleting process.

This study analyzes the effects of N fertilizer application rates on profitability of growing switchgrass and using the feedstock in a pyrolysis biorefinery facility to create a source of sustainable aviation fuel (SAF) supply in Tennessee. Switchgrass (Panicum virgatum L.) is a perennial bunchgrass native to North America with traits suitable for biofuel and co-product production. Previous chemical analysis has shown that ash content in switchgrass is related to the amount of nitrogen applied to the field, while at the biorefinery level, the percentage ash content reduces the biorefinery fuel output. To obtain optimal nitrogen (N) application rates for the switchgrass producers and the biorefinery, a two-part analysis is employed. First, a partial budgeting profitability analysis is conducted for this cropping enterprise at the farm-gate level without considering downstream implications of biomass quality, i.e., ash content. Second, the effects of higher ash content as a percentage of the feedstock on biorefinery output are analyzed. Results show farm-gate profit is maximized when N fertilizer is applied at 111 kg/ha, while as a result of increased production levels and decreased percentage ash content, biorefinery profit is maximized when N is applied at 157 kg/ha. Lower ash could lead to premium prices paid to switchgrass producers if higher quality feedstock were to be demanded as part of an integrated biofuel industry.

This study aims to optimize strong acid hydrolysis-based production of cellulose nanocrystals (CNCs) and cellulose nanofibers (CNFs) from pre-extracted and fully bleached kraft pulp of loblolly pinewood, the most abundant and commercially significant softwood species in southeastern United States. The effect of four parameters, including acid concentration, temperature, duration and pulp particle size, on the yield and properties of CNCs was investigated using the central composite design (CCD) of response surface methodology (RSM) for process optimization. While CNC yield was significantly affected by acid concentration and hydrolysis temperature and was adequately explained by an empirical model, none of the characteristic properties of CNCs, including crystallinity index, surface charge and particle size, displayed any strong correlation to the process parameters within the experimental ranges tested. At different hydrolysis severities, we not only analyzed the waste streams to determine the extent of holocellulose degradation, but also evaluated the properties of leftover partially hydrolyzed pulp, called cellulosic solid residues (CSR), to gauge its potential for CNF production via mechanical fibrillation. Conditions that maximized CNC yields (60% w/w) were 60% acid concentration, 58 °C, 60 min and 40 mesh particle size. Twenty percent (w/w) of the pulp was degraded under these conditions. On the other hand, conditions that maximized CSR yields (60% w/w) were 54% acid, 45 °C, 90 min and 20 mesh particle size, which also produced 15% CNCs, caused minimal pulp degradation (

Development of cross-linked, soft polymeric materials from biomass has been a focus of research. The aqueous phase of biomass pyrolysis oil (bio-oil) has been used as a precursor for monomer synthe...

A statistical response surface methodology (RSM) using a central composite design (CCD) model was applied to identify the optimum thermal desorption conditions for maximum recovery of preservative from copper naphthenate (CuNap) treated wood and subsequent production of a high quality pyrolytic vapor from the thermally treated wood. From the designed experiment, 94% of the total preservative present in the ties was desorbed at temperatures higher than 250 °C and residence times longer than 30 min. Elevating the temperature from 215 °C to 285 °C for 45 min residence time generated a weight loss of 12–36 wt%, an increase in higher heating value (HHV) from 20.1 to 21.9 MJ/kg, and a reduction of energy yield from 90.4 to 71.5% of the resulting thermally treated biomass. Pyrolysis at 450 °C of this material produced a vapor rich in sugars- and lignin-derived compounds. The predicted optimum conditions in terms of a maximum preservative recovery, minimum energy yield loss of the wood, and production of thermally treated biomass that generates a high proportion of sugars- and lignin-derived compounds during pyrolysis were found to be 265 °C and 51 min. Under these optimum conditions, the predicted maximum preservative recovery was 95% while the predicted thermally treated solid retained 77% of the original energy yield and produced high portions of levoglucosan and lignin-derived compounds during subsequent pyrolysis, similar to torrefied wood.

Lignocellulosic biomass is an alternative source of energy that can reduce our dependency on fossil fuels and limit greenhouse gas emissions. Several techno-economic analyses have consistently shown that all the steps in biomass-to-bioproduct processes needs improvement. Simultaneous assessment of genotypes for multiple productivity characteristics and integrating information across production stages has seldom been the focus of research efforts. To address this gap, we first determined the agronomic performance of 10 poplar genotypes. Differences between genotypes in height, diameter at breast height (DBH), tree mass and yield were consistently observed. Correlation analyses revealed that height and DBH are positively correlated with tree mass and yield, whereas bark content is negatively correlated with tree mass, yield and disease incidence. Four highest-yielding genotypes were subjected to proximate, ultimate, targeted chemical analyses, along with assessment of sugar production by acid hydrolysis and enzymatic saccharification. Despite having only marginal changes in overall chemistry, the genotypes showed differential conversion efficiencies of enzymatic saccharification. Interestingly, the genotype that showed highest cellulose conversion efficiency had the lowest estimated sugar yields due to its low biomass yield, whereas the genotype with lowest conversion efficiency had the highest estimated sugar yields. These results show the importance of integrating information across the stages of biomass production and bioconversion. These results also demonstrate the complexity of biomass feedstock production and the need for future studies to assess whether these tradeoffs can be genetically separated to guide the selection of genotypes that can maximize the overall biomass feedstock production efficiency.

The sorption/desorption of gallic acid, a simple phenolic compound, was studied experimentally in a batch system. The motivation for this project was to provide insight into the recovery of phenolic compounds from switchgrass. Recovery of phenolic compounds could enhance the sustainability and economics of biorefining facilities. The sorption/desorption of gallic acid was shown to be qualitatively similar to that of phenolics extracted from switchgrass; so more extensive studies were made using gallic acid as a surrogate for the complex mixtures of phenolic compounds leached from switchgrass. The kinetics indicate that an approximation of equilibrium was reached within 48 h. Activated carbon was demonstrated to sorb gallic acid and phenolics from water and aqueous switchgrass leachate. The loading capacity of activated carbon for the gallic acid–water-activated carbon system increased with temperature for 20 to 60 °C. Ethanol was shown to be a preferable elution agent for desorbing gallic acid from activa...

In this study, the results from laboratory measurements of the devolatilization kinetics of switchgrass in a rapidly heated fixed bed reactor flushed with argon and operated at constant temperatures between 600 and 800°C was reported. Results indicate that switchgrass decomposes in two sequential stages during pyrolysis: stage I involves the evaporation and devolatilization of water and extractives and stage II involves that of hemicellulose, cellulose, and lignin. The estimated global activation energy for stage II increased from 52.80 to 59.39kJ/mol as the reactor temperature was increased from 600 to 800°C. The maximum conversion of carbon, hydrogen, oxygen, sulfur, and nitrogen ranged from 0.68 to 0.70, 0.90 to 0.95, 0.88 to 0.91, 0.70 to 0.80, and 0.55 to 0.66, respectively. The retention of alkali and alkaline earth metal (AAEM) species in the solid char after complete pyrolysis was significantly higher than in the original feed, indicating the importance of AAEM species in subsequent char processing.

A two-step thermochemical process combining a thermal desorption at 250–300 °C and a pyrolysis at 500 °C of used creosote-treated wooden railroad ties was carried out to recover preservative and produce a high quality bio-oil and biochar. Under optimal temperature between 280 and 300 °C, high preservative removal efficiency (70–74%) was achieved with a high proportion of polycyclic aromatic hydrocarbons (PAHs, 80–82%) and a large portion of the original wood mass (67–70%) was retained. This thermally treated biomass had higher heating value (HHV; 19.9–20 MJ/kg) than the starting material. The physical properties of the preservative, such as viscosity and density, and its toxic threshold against a common decay basidiomycete fungus were similar to those of commercially available P2-creosote. Pyrolysis of the thermally treated ties produced bio-oils with lower water content and total acid numbers, and a higher amount of lignin-derived compounds than that of untreated ties. Biochars derived from the thermally...

Reforming whole lignocellulosic biomass into value-added materials has yet to be achieved mainly due to the infusible nature of biomass and its recalcitrance to dissolve in common organic solvents. Recently, the solubility of biomass in ionic liquids (ILs) has been explored to develop all-lignocellulosic materials; however, efficient dissolution and therefore production of value-added materials with desired mechanical properties remain a challenge. This article presents an approach to producing high-performance lignocellulosic films from hybrid poplar wood. An autohydrolysis step that removes ≤50% of the hemicellulose fraction is performed to enhance biomass solvation in 1-ethyl-3-methyl imidazolium acetate ([C2mim][OAc]). The resulting biomass–IL solution is then cast into free-standing films using different coagulating solvents, yet preserving the polymeric nature of the biomass constituents. Methanol coagulated films exhibit a cocontinuous 3D-network structure with dispersed domains of less than 100 nm...

© 2017 American Chemical Society. We have prepared composite materials of hexagonal nickel phosphide and molybdenum carbide (Mo2C) utilizing a simple and scalable two-stage synthesis method composed of carbothermic reduction followed by hydrothermal incubation. We observe the monophasic hexagonal phosphide Ni2P in the composite at low phosphide-to-carbide (P:C) ratios. Upon an increase in the proportion of P:C, the carbide surface becomes saturated, and we detect the emergence of a second hexagonal nickel phosphide phase (Ni5P4) upon annealing. We demonstrate that vapor-phase upgrading (VPU) of whole biomass via catalytic fast pyrolysis is achievable using the composite material as a catalyst, and we monitor the resulting product slates using pyrolysis-gas chromatography/mass spectrometry. Our analysis of the product vapors indicates that variation of the P:C molar ratio in the composite material affords product slates of varying complexity and composition, which is indicated by the number of products and their relative proportions in the product slate. Our results demonstrate that targeted vapor product composition can be obtained, which can potentially be utilized for tuning of the composition of the bio-oil downstream.

© 2019 American Chemical Society. Mixed-metal oxides possess a wide range of tunability and show promise for catalytic stabilization of biomass pyrolysis products. For materials derived from layered double hydroxides, understanding the effect of divalent cation species and divalent/trivalent cation stoichiometric ratio on catalytic behavior is critical to their successful implementation. In this study, four mixed-metal oxide catalysts consisting of Al, Zn, and Mg in different stoichiometric ratios were synthesized and tested for ex-situ catalytic fast pyrolysis (CFP) using pine wood as feedstock. The catalytic activity and deactivation behavior of these catalysts were monitored in real-time using a lab-scale pyrolysis reactor and fixed catalyst bed coupled with a molecular beam mass spectrometer (MBMS), and data were analyzed by multivariate statistical approaches. In the comparison between Mg-Al and Zn-Al catalyst materials, we demonstrated that the Mg-Al materials possessed greater quantities of basic sites, which we attributed to their higher surface areas, and they produced upgraded pyrolysis vapors which contained less acids and more deoxygenated aromatic hydrocarbons such as toluene and xylene. However, detrimental impacts on carbon yields were realized via decarbonylation and decarboxylation reactions and coke formation. Given that the primary goals of catalytic upgrading of bio-oil are deoxygenation, reduction of acidity, and high carbon yield, these results highlight both promising catalytic effects of mixed-metal oxide materials and opportunities for improvement.

Inorganic elements present in lignocellulosic biomass and introduced during harvesting and handling of the feedstock negatively affect biomass conversion to fuels and products. In particular, alkali and alkaline earth metals act as catalysts during thermochemical conversion, contribute to reactor degradation, and decrease the yield and quality of the reaction products. In this study, we investigated an approach to reduce ash content of switchgrass. Several reagents (chelating agents ethylenediaminetetraacetic acid (EDTA) and citric acid, as well as acetic acid, sulfuric acid, and water) under various extraction times (5, 10, 15, and 20 min) were tested using a microwave-assisted extraction method. After the extraction, mass loss, total ash, individual inorganics, and concentration of sugars in the hydrolyzates were measured. EDTA afforded the highest inorganics removal, with near complete extraction of alkali and alkaline earth metals K, Ca, and Mg, and high removal of S and Si. Citric acid and sulfuric acid removed similarly high amounts of K, Ca, and Mg as EDTA, but less Mg, P, S, and Fe. Additionally, extraction with water resulted in near complete removal of K; however, more modest removal of other inorganics was observed compared to other treatments. The mass loss was significantly higher in the sulfuric acid extractions due to hydrolysis of the structural carbohydrates, while EDTA resulted in little carbohydrate degradation due to the more neutral pH conditions. This study illustrated the benefits of extracting with chelating agents, as opposed to mineral acids, to remove inorganics and improve biomass quality.

The aim of this work was to evaluate the efficiency of an ionic liquid (IL) 1-butyl-3-methylimidazolium acetate ([C4mim][OAc]) pretreatment (110°C for 30min) in comparison to high severity autohydrolysis pretreatment in terms of delignification, cellulose crystallinity and enzymatic digestibility. The increase in severity of autohydrolysis pretreatment had positive effect on glucan digestibility, but was limited by the crystallinity of cellulose. [C4mim][OAc] pretreated sugarcane bagasse exhibited a substantial decrease in lignin content, reduced cellulose crystallinity, and enhanced glucan and xylan digestibility. Glucan and xylan digestibility was determined as 97.4% and 98.6% from [C4mim][OAc] pretreated bagasse, and 62.1% and 57.5% from the bagasse autohydrolyzed at 205°C for 6min, respectively. The results indicated the improved digestibility and hydrolysis rates after [C4mim][OAc] pretreatment when compared against a comparable autohydrolyzed biomass.

Non-structural components, such as inorganics and organic extractives, present in switchgrass were extracted with water and ethanol, and the resulting non-structural components-free materials were pyrolyzed to investigate the effect of the inorganic species on the pyrolytic products. The extraction was performed for switchgrass materials harvested from three consecutive growing seasons, removing 8.5 wt% of the organic extractives in the first season biomass, and 5.8 and 6.3 wt% in the second and third season, respectively, on total dry basis of biomass. In addition to organic extractives, from 0.7 to 2.7 wt% of ash were extracted. Specifically, 99% and 59% of total K and Mg were removed from the switchgrass harvested in the second and third growing season. Thermogravimetric analysis demonstrated that a predominant reduction of K and Mg content in the biomass increased temperature at which mass loss rate is maximized in the decomposition of cellulose, hemicellulose, and lignin. The reduction of K and Mg content also affected pyrolytic products generated at 450°C. The chromatographic peak area percentage of levoglucosan from the extracted samples in the second and third growing season was two to three times higher than that from the extracted samples in the first growing season, showing a strong negative correlation with K and Mg content, whereas most of the light oxygenated and furanic/pyranic/cyclopentanic products exhibited a strong positive correlation with K and Mg content. We concluded that the removal of non-structural components prior to thermochemical conversion processes such pyrolysis can potentially produce a valuable extractives stream while removing catalytic inorganics that negatively impact downstream pyrolysis process.

Background Lignocellulosic biomass requires either pretreatment and/or fractionation to recover its individual components for further use as intermediate building blocks for producing fuels, chemicals, and products. Numerous ionic liquids (ILs) have been investigated for biomass pretreatment or fractionation due to their ability to activate lignocellulosic biomass, thereby reducing biomass recalcitrance with minimal impact on its structural components. In this work, we studied and compared 1-allyl-3-methylimidazolium formate ([AMIM][HCOO]) to the commonly used 1-ethyl-3-methylimidazolium acetate ([EMIM][CH3COO]) for its potential to activate hybrid poplar biomass and enable high cellulose and hemicellulose enzymatic conversion. Although [EMIM][CH3COO] has been widely used for activation, [AMIM][HCOO] was recently identified to achieve higher biomass solubility, with an increase of 40% over [EMIM][CH3COO]. Results Since IL activation is essentially an early stage of IL dissolution, we assessed the recalcitrance of [EMIM][CH3COO] and [AMIM][HCOO]-activated biomass through a suite of analytical tools. More specifically, Fourier transform infrared spectroscopy and X-ray diffraction showed that activation using [AMIM][HCOO] does not deacetylate hybrid poplar as readily as [EMIM][CH3COO] and preserves the crystallinity of the cellulose fraction, respectively. This was supported by scanning electron microscopy and enzymatic saccharification experiments in which [EMIM][CH3COO]-activated biomass yielded almost twice the cellulose and hemicellulose conversion as compared to [AMIM][HCOO]-activated biomass. Conclusion We conclude that the IL [AMIM][HCOO] is better suited for biomass dissolution and direct product formation, whereas [EMIM][CH3COO] remains the better IL for biomass activation and fractionation.

An abundant, low-cost, and high-quality supply of lignocellulosic feedstock is necessary to realize the large-scale implementation of biomass conversion technologies capable of producing renewable fuels, chemicals, and products. Barriers to this goal include the variability in the chemical and physical properties of available biomass, and the seasonal and geographic availability of biomass. Blending several different types of biomass to produce consistent feedstocks offers a solution to these problems and allows for control over the specifications of the feedstocks. For thermochemical conversion processes, attributes of interest include carbon content, total ash, specific inorganics, density, particle size, and moisture content. In this work, a series of switchgrass and pine residues blends with varying physical and chemical properties were evaluated. Physical and chemical properties of the pure and blended materials were measured, including compositional analysis, elemental analysis, compressibility, flowability, density, and particle size distribution. To screen blends for thermochemical conversion behavior, the analytical technique, pyrolysis gas chromatography mass spectrometry (Py-GC/MS), was used to analyze the vapor-phase pyrolysis products of the various switchgrass/pine residues blends. The py-GC/MS findings were validated by investigating the bio-oils produced from the selected blends using a lab-scale fluidized-bed pyrolysis reactor system. Results indicate that the physical properties of blended materials are proportional to the blend ratio of pure feedstocks. In addition, pyrolysis of pine residues resulted in bio-oils with higher carbon content and lower oxygen content, while switchgrass derived pyrolysis products contained relatively greater amount of anhydrosugars and organic acids. The distribution of the pyrolysis vapors and isolated bio-oils appear to be a simple linear combination of the two feedstocks. The concentration of alkali and alkaline earth metals (Ca, K, Mg, and Na) in the blended feedstocks were confirmed to be a critical parameter due to their negative effects on the bio-oil yield. This work demonstrates that blending different sources of biomass can be an effective strategy to produce a consistent feedstock for thermochemical conversion.

A new approach to hydrogen production using an integrated pyrolysis–microbial electrolysis process is described. The aqueous stream generated during pyrolysis of switchgrass was used as a substrate for hydrogen production in a microbial electrolysis cell, achieving a maximum hydrogen production rate of 4.3 L H2/L anode-day at a loading of 10 g COD/L-anode-day. Hydrogen yields ranged from 50 ± 3.2% to 76 ± 0.5% while anode Coulombic efficiency ranged from 54 ± 6.5% to 96 ± 0.21%, respectively. Significant conversion of furfural, organic acids and phenolic molecules was observed under both batch and continuous conditions. The electrical and overall energy efficiency ranged from 149–175% and 48–63%, respectively. The results demonstrate the potential of the pyrolysis–microbial electrolysis process as a sustainable and efficient route for production of renewable hydrogen with significant implications for hydrocarbon production from biomass.

Background Genetically engineered biofuel crops, such as switchgrass (Panicum virgatum L.), that produce their own cell wall-digesting cellulase enzymes would reduce costs of cellulosic biofuel production. To date, non-bioenergy plant models have been used in nearly all studies assessing the synthesis and activity of plant-produced fungal and bacterial cellulases. One potential source for cellulolytic enzyme genes is herbivorous insects adapted to digest plant cell walls. Here we examine the potential of transgenic switchgrass-produced TcEG1 cellulase from Tribolium castaneum (red flour beetle). This enzyme, when overproduced in Escherichia coli and Saccharomyces cerevisiae, efficiently digests cellulose at optima of 50 °C and pH 12.0. Results TcEG1 that was produced in green transgenic switchgrass tissue had a range of endoglucanase activity of 0.16–0.05 units (µM glucose release/min/mg) at 50 °C and pH 12.0. TcEG1 activity from air-dried leaves was unchanged from that from green tissue, but when tissue was dried in a desiccant oven (46 °C), specific enzyme activity decreased by 60%. When transgenic biomass was “dropped-in” into an alkaline buffer (pH 12.0) and allowed to incubate at 50 °C, cellobiose release was increased up to 77% over non-transgenic biomass. Saccharification was increased in one transgenic event by 28%, which had a concurrent decrease in lignin content of 9%. Histological analysis revealed an increase in cell wall thickness with no change to cell area or perimeter. Transgenic plants produced more, albeit narrower, tillers with equivalent dry biomass as the control. Conclusions This work describes the first study in which an insect cellulase has been produced in transgenic plants; in this case, the dedicated bioenergy crop switchgrass. Switchgrass overexpressing the TcEG1 gene appeared to be morphologically similar to its non-transgenic control and produced equivalent dry biomass. Therefore, we propose TcEG1 transgenics could be bred with other transgenic germplasm (e.g., low-lignin lines) to yield new switchgrass with synergistically reduced recalcitrance to biofuel production. In addition, transgenes for other cell wall degrading enzymes may be stacked with TcEG1 in switchgrass to yield complementary cell wall digestion features and complete auto-hydrolysis.

© 2017 American Chemical Society. Removal of copper naphthenate (CN) from used wooden railroad ties was investigated to improve the commercial viability of this biomass as a fuel source and avoid alternative disposal methods such as landfilling. Bench-scale thermal desorption of organic preservative components from CN-impregnated ties was followed by extraction of the copper fraction with ethylenediaminetetraacetic acid, 1-hydroxy ethylidene-1,1-diphosphonic acid, or 2,6-pyridine dicarboxylic acid (PDA). Naphthenic acid (NA) and carrier oil were recovered at desorption temperatures between 225 and 300 °C and could potentially be recycled to treat new ties. The thermal treatment also mimicked torrefaction, improving the biomass properties for use as a thermochemical conversion feedstock. Chelation with PDA, a biodegradable chelating agent, after desorption had the highest extraction efficiency of copper and other naturally present inorganics, extracting 100% of the copper from both the raw and 225 °C-treated samples. Optimized desorbed material showed a 64% decrease in ash content when extracted with PDA; however, extraction efficiency decreased as desorption temperature increased, indicating that thermal treatment caused the inorganics to be less extractable. We concluded that the optimum desorption conditions were between 250 and 275 °C for 45 min followed by extraction with PDA when considering both NA removal and inorganic extraction efficiency.

Switchgrass (Panicum virgatum) is a perennial grass that has emerged as an ideal candidate for production of biofuel and value-added co-products. One of the primary requirements for the successful manufacturing of these switchgrass-derived bioproducts is to produce a consistent feedstock with reliable and adequate amounts of the substrate constituent needed. For example, the biofuels industry requires a fast-growing energy crop with higher cellulose content and lower inhibitors found in secondary constituents. Other industries would profit from higher lignin content for products such as carbon fibers, or higher water and ethanol-soluble extracts containing compounds of interest. Two switchgrass field plots in eastern Tennessee were monitored over a period of six months, including before and after traditional harvesting times for the biorefinery. Characterization of the biomass and its constituents, such as water and ethanol extracts, cellulose, hemicelluloses, lignin, and ash, was performed to examine chemical changes in switchgrass that occurred prior to, during, and after traditional harvesting times used in a biorefinery setting. Total carbohydrate (65.6–66.7 wt%) and lignin (21.7–23.2 wt%) content was found to peak in January. Extractives content was at a maximum in early harvests at 15.9–16.6 wt% and decreased to 5.5–5.8 wt% in February. An inverse relationship exists between the extractives and lignin content (R2 = 0.94). Nonstructural soluble sugars peaked in early October with 5.1 wt% of the switchgrass composition. Remobilization efficiencies of K, Mg, P, and Fe increased with time, indicating conservation of soil nutrients if harvests were completed in late winter.

Switchgrass (Panicum virgatum L.) is a candidate feedstock in bioenergy, and plant breeding and molecular genetic strategies are being used to improve germplasm. In order to assess these subsequent modifications, baseline biomass compositional data are needed in a relevant variety of environments. In this study, switchgrass cv. Alamo was grown in the field, greenhouse, and growth chamber and harvested into individual leaf and stem tissue components. These components were analyzed with pyrolysis vapor analysis using molecular beam mass spectrometry, Fourier transform infrared, and standard wet chemistry methods to characterize and compare the composition among the different growth environments. The details of lignin content, S/G ratios, and degree of cross-linked lignin are discussed. Multivariate approaches such as projection to latent structures regression found a very strong correlation between the lignin content obtained by standard wet chemistry methods and the two high throughput techniques employed to rapidly assess lignin in potential switchgrass candidates. The models were tested on unknown samples and verified by wet chemistry. The similar lignin content found by the two methods shows that both approaches are capable of determining lignin content in biomass in a matter of minutes.

Chars from the thermal degradation of silver maple (Acer saccharinum), red maple (Acer rubrum), sugar maple (Acer saccharum), and white oak (Quercus spp.), performed at temperatures from 250 to 350 °C, were examined using time domain-nuclear magnetic resonance spectroscopy. Prior to analysis, the chars were equilibrated under conditions insuring the presence of bound water only and both bound water and free water. Transverse relaxation times were found to be related to the moisture content of the chars, which varied with temperature. At elevated temperatures the number of signals assigned to free water decreased, indicative of an increase in pore size within the chars.

In recent years, bioenergy has become a promising renewable energy source that can potentially reduce the greenhouse emissions and generate economic growth in rural areas. Gaining understanding and controlling biomass chemical composition contributes to an efficient biofuel generation. This paper presents a principal component analysis (PCA) that shows the influence and relevance of selected controllable factors over the chemical composition of switchgrass and, therefore, in the generation of biofuels. The study introduces the following factors: (1) storage days; (2) particle size; (3) wrap type; and (4) weight of the bale. Results show that all the aforementioned factors have an influence in the chemical composition. The number of days that bales have been stored was the most significant factor regarding changes in chemical components due to its effect over principal components 1 and 2 (PC1 and PC2, approximately 80% of the total variance). The storage days are followed by the particle size, the weight of the bale and the type of wrap utilized to enclose the bale. An increment in the number of days (from 75–150 days to 225 days) in storage decreases the percentage of carbohydrates by −1.03% while content of ash increases by 6.56%.

Fractionation of lignocellulosic biomass is an attractive solution to develop an economically viable biorefinery by providing a saccharide fraction to produce fuels and a lignin stream that can be converted into high value products such as carbon fibers. In this study, the analysis of ionic liquid-activated biomass demonstrates that in addition of decreasing crystallinity, the selected ILs (1-butyl-3-methylimidazolium acetate, 1-butyl-3-methylimidazolium chloride and 1-ethyl-3-methylimidazolium acetate) deacetylate Yellow poplar under mild conditions (dissolution at 60–80 °C), and lower the degradation temperature of each biomass polymeric component, thereby reducing the recalcitrance of biomass. Among the three tested ILs, 1-ethyl-3-methylimidazolium acetate performed the best, providing a strong linear relationship between the level of deacetylation and the rate of enzymatic saccharification for Yellow poplar.

Bamboo has wide range of moisture content, low bulk energy density and is difficult to transport, handle, store and feed into existing combustion and gasification systems. Because of its important fuel characteristics such as low ash content, alkali index and heating value, bamboo is a promising energy crop for the future. The aim of this study was to evaluate the effects of torrefaction on the main energy properties of Bambusa vulgaris . Three different torrefaction temperatures were employed: 220, 250 and 280 °C. The elemental characteristics of lignite and coal were compared to the torrefied bamboo. The characteristics of the biomass fuels tend toward those of low rank coals. Principal component analysis of FTIR data showed a clear separation between the samples by thermal treatment. The loadings plot indicated that the bamboo samples underwent chemical changes related to carbonyl groups, mostly present in hemicelluloses, and to aromatic groups present in lignin.

Rapid methods for the characterization of biomass for energy purpose utilization are fundamental. In this work, near infrared spectroscopy is used to measure ash and char content of various types of biomass. Very strong models were developed, independently of the type of biomass, to predict ash and char content by near infrared spectroscopy and multivariate analysis. Several statistical approaches such as principal component analysis (PCA), orthogonal signal correction (OSC) treated PCA and partial least squares (PLS), Kernel PCA and PLS were tested in order to find the best method to deal with near infrared data to classify and predict these biomass characteristics. The model with the highest coefficient of correlation and the lowest RMSEP was obtained with OSC-treated Kernel PLS method.