Search

The combined star/pentagon connection of five-phase induction machines was recently demonstrated as a promising compromise between conventional star and pentagon connections. It combines the advantages of both star and pentagon connections without any additional hardware for winding changeover. This connection is based on two five-phase single layer concentrated winding sets shifted in space by π/10 and connected in a combined star/pentagon configuration to provide five-phase terminals. Since the combined star/pentagon connected induction machine is fundamentally an asymmetrical ten-phase machine, the machine mathematical model possesses additional subspaces, which affect the behavior of the machine especially under open line conditions. Starting from the conventional five-phase and m -bar squirrel cage induction machine model, the phase-variable model of the combined star/pentagon connection is introduced in this paper. The corresponding equivalent dq model with five decoupled subspaces, which can account for air gap harmonics up to ninth order, is then derived. Finally, it was shown that the machine model could be simply approximated with only two subspaces similar to a conventional five-phase induction machine with sinusoidally distributed winding, where the flux produced by the nonfundamental subspace could be neglected. The model is verified using a 1 kW prototype five-phase induction machine. [ABSTRACT FROM PUBLISHER]

In electric drive applications that are based on high‐speed induction motors (IMs) with an extended speed range, stator winding pole‐changing is a possible technique to avoid oversizing the driving motor. The electronic pole changing employed in multiphase IMs has gained recent interest because it avoids physical winding reconfiguration. The effective number of poles of the air gap flux distribution can be electronically altered by simply changing the applied current sequence to a multiphase stator. The main problem associated with this technique is the significant increase in machine magnetising current with the increase in effective pole number when conventional multiphase distributed windings are employed. This study proposes a new fractional‐slot concentrated winding layout with a special stator connection suitable for pole‐amplitude modulated IMs that offers a 2:1 pole ratio while maintaining equal magnetising current for both winding pole pairs. Moreover, constant power operation can be achieved for a speed range of over 4 pu. The main concept is discussed and verified through simulations and experimentally. The machine mathematical model and the required vector space decomposition‐based controller are also presented. [ABSTRACT FROM AUTHOR]

Despite the increased interest in multiphase induction machines for safety-critical applications, machine parameter identification for the different sequence planes is still a challenging research point. In most available literature, the effect of nonfundamental sequence planes is overlooked due to the assumption of sinusoidal winding distribution and healthy operation. However, in a single layer or concentric winding layout with an odd number of phases, the effect of flux produced by nonfundamental sequence planes cannot be ignored for the open-phase case. This paper proposes a simple offline method to estimate the parameters of a five-phase induction machine corresponding to different sequence planes. The proposed technique can estimate the stator leakage inductance as well as the magnetizing inductance of both fundamental and third sequences by applying a quasi-square voltage to the stator winding while the machine is running at no-load. Consequently, the rotor circuit parameters of the fundamental sequence plane can be simply obtained by deducting the stator impedance from the blocked rotor machine impedance. For the third sequence plane, an approximate relation to estimate these parameters based on the measured fundamental sequence rotor parameters is also given. An experimental 1.5 Hp prototype machine is used to verify the proposed technique. [ABSTRACT FROM PUBLISHER]

Although torque enhancement in multiphase induction machines using harmonic current injection has been addressed in the literature, a detailed assessment of the effect of this enhancement on the design parameters of multiphase machines with different numbers of phases is needed. This paper addresses this topic by performing a detailed comparative study of harmonic injection torque enhancement on multiphase machines with different numbers of phases. Sets of identical dimension and volume rotors differing in their value of the bar skew angle were designed to operate with the various stator designs in order to facilitate the comparative evaluation. A mathematical approach is also introduced to enable the derivation of equivalent multiphase machine parameters based on an existing one. In addition to a detailed finite-element-analysis verification of the results, time domain MATLAB simulations are used to verify the mathematical modeling. The results provide a means to assess the extent to which such harmonic injection may be beneficial by quantifying torque enhancement as well as torque density for various multiphase machines. [ABSTRACT FROM AUTHOR]

This study proposes a new architecture of flywheel energy storage system (FESS) which can be implemented at generating unit (GU) level (e.g. wind turbine) or scaled up for application in grid‐side converter (GSC) stations of a multi‐terminal direct current (MTDC) system. The proposed architecture suppresses DC voltage leaps under grid faults, and performs power levelling duty at grid connection points. When implemented at GU level, the proposed FESS features a doubly‐fed induction machine (DFIM) – the flywheel machine – where its six stator winding terminals are connected in series between the grid and the GSC. The flywheel converter is of partial power rating, and is connected to the DFIM rotor. When employed at an MTDC GSC station, several submodules are connected to build an FESS station. The study proposes the control concept and the general topology of the FESS station. The performance parameters of the system are tested under normal and abnormal operating conditions. Results and analyses indicate smooth dynamic operation, the economic advantage and the improved fault ride‐through capability because of the proposed system. [ABSTRACT FROM AUTHOR]