Search

Abstract The thermal performance of the evacuated tube solar collector with WO 3 /Water Nanofluid was studied in this paper. The WO 3 nanoparticles were spherical with 90 nm diameter Three different volume fraction of WO 3 nanoparticles of 0.014%, 0.028%, and0.042% were examined at several mass flux rates of 0.013 kg/s.m2, 0.015 kg/s.m2 and 0.017 kg/s.m2. The stability of the nanofluid was checked. Experiments were performed in Budapest, Hungary on the latitude of 47°28′N and longitude of 19°03′E. The results showed that the temperature difference of the fluid increased up to 21% with adding WO 3 nanoparticles. The maximum heat gain at the solar irradiance of 900 W/m2 was raised up to 23% when WO 3 nanoparticles were used. The proportion of the growth of the heat removable factor for nanofluids comparing to water at the same mass flux rate is between 1.05 and 1.16. The results indicated that the efficiency of the evacuated tube solar collector enhanced with more nanoparticles added. The thermal-optical efficiency of the evacuated tube solar collector reached 72.8%. Highlights • A good stability WO 3 /water nanofluid was prepared at different volume fraction. • The collector outlet temperature and heat gain enhanced with 21% and 23%, respectively. • The ratio of the increase of the heat removable factor for nanofluids was between 1.05 and 1.16%. • The thermal-optical efficiency of the collector reached 72.83%. [ABSTRACT FROM AUTHOR]

Nanofluids are the most attractive mean to enhance the performance of heat transfer devices. Several types of nanoparticles were utilized as they have high thermal conductivity. Renewable energy makes use of these nanofluids special in solar collectors. Evacuated tube solar collector is one of the most utilized solar collectors in thermal applications. CeO 2 nanoparticles were used in the presented study. The mean diameter of CeO 2 was 25 nm. A stable CeO 2 /water was made. The stability was checked using Zeta potential machine. Experiments were carried out using three different volume concentration of CeO 2 nanoparticles of 0.015%, 0.025%, and 0.035%. The thermal performance of the evacuated tube solar collector was examined at different mass flux rates. Results showed that the temperature difference between inlet and outlet flow and absorbed energy increase when nanofluids are used. The volume fraction flow rate of 0.035% at the mass flux rate of 0.017 kg/s.m 2 had the maximum heat removable factor, the thermo-optical characteristic of the collector, and the thermal loss coefficient. The thermo-optical characteristic of the collector of tube solar corrector is raised up to 34%. [ABSTRACT FROM AUTHOR]

Using nanofluids in thermal energy devices, such as flat-plate solar collectors, is gradually making progress, and getting awareness in the scientific community. Experiments were performed to study the effect of using CeO 2 -water on the efficiency of flat-plate solar collector by three different volume fractions of CeO 2 nanoparticles of 0.0167%, 0.0333% and 0.0666%, while the mean particle dimension was kept constant at 25 nm. An ultrasonic process was used for maintaining the stability of the CO 2 -water nanofluid. The working fluid mass flux rates were 0.015, 0.018 and 0.019 kg/s m 2 . The experiments were carried out in Budapest, Hungary on the latitude of 47°28′N and longitude of 19°03′E. Higher collector efficiency was achieved when using CeO 2 -water nanofluid compared to results achieved with water application. Based on present data, the efficiency of the collector is directly proportional with the mass flux rate and with the volume fraction in the ranges of the present study. Experiments indicate that the highest rise in efficiency of the collector at zero value of [(T i  – T a )/G T ] is 10.74%, for volume fraction ( φ ) 0.066%, and for mass flux rate of 0.019 kg/s m 2 compared to water. [ABSTRACT FROM AUTHOR]

• Technical, economic and environmental modeling frameworks are proposed. • Economic and environmental optima of hybrid renewable energy systems are different. • Local climatic conditions highly influence the impacts and the optimal design. • Single- and multi-objective optimization both have advantages and disadvantages. • Installing photovoltaics is the cheapest way to decrease environmental impacts. The rapid spread of renewables made it essential to design optimal hybrid renewable energy systems (HRES) with the distinctive economic and environmental impacts of each technology in mind. According to a comprehensive literature review, very few studies consider life-cycle environmental impacts in small-scale hybrid renewable energy system optimization. This paper aims to fill this gap by providing a multi-objective design framework for household-scale systems based on the technical modeling of several typical components. Solar photovoltaic, wind turbine, solar heat collector, heat pump, heat storage, battery, and as a novelty, heat insulation thickness are considered. Backup power is either drawn from the grid or produced by a diesel generator in grid-connected and off-grid scenarios, respectively. Single objective optimization using genetic algorithm resulted in the least cost and the least environmental footprint options in a case study of three different locations across Europe. Then, Pareto-optimal solutions between the two extremities were explored with a multi-objective genetic algorithm. Single objective results show substantial differences between environmental and economic optima, while multi-objective optimization proved to be an efficient tool to investigate the trade-offs between the two conflicting goals. Solar photovoltaics is proved to be the most competitive technology to reduce environmental impacts in the case of grid-connected systems. Off-grid systems, however, benefit the most from a balanced mix of different renewable energy sources. Life-cycle impacts in the design of systems involving renewables is proven to be relevant while potential applications of the framework are also revealed. Further research areas, as well as the limitations of the methodology are identified in the conclusion. [ABSTRACT FROM AUTHOR]

From both environmental and energy-saving points of view, solar heating and cooling systems have recently proven themselves in the commercial world as the environmentally friendly and sustainable energy systems which can replace the systems powered by conventional sources of energy such as fossil fuels and electricity. In the present paper, the research contributions conducted on solar absorption cooling systems, integrated with different auxiliary energy devices, are comprehensively reviewed and discussed. Also, various cooling systems integrated with solar technologies, i.e., flat-plate collector, evacuated tube collector, compound parabolic collector and parabolic trough collector, are reviewed. The survey and comparison are carried out in terms of some crucial parameters such as coefficient of performance, annual energy consumption and payback period. Further, this work briefly presents and discusses some possible opportunities for future works from the efficiency viewpoint. [ABSTRACT FROM AUTHOR]