Search

Managing solar energy utilization and water heating in multi-apartment buildings presents formidable challenges due to limited space for solar collector installation. Optimizing heat energy distribution among communal consumers is crucial, necessitating precise regulation of hot water flow from the main system line to individual thermal storage tanks. The objective is to minimize heat and electricity losses while maximizing temperature levels in each tank. An electronic control system, centered around a microcontroller, has been developed with an efficient algorithm, data storage memory, and communication capabilities. The implemented solar heating system is tailored to each individual consumer, incorporating precise measurements for every apartment. This customization enhances efficiency not only for the individual consumer but also benefits the overall solar system within the building. This article explores the development and past outcomes of implementing such a control system, highlighting its significant advantages, particularly in multi-story buildings. [ABSTRACT FROM AUTHOR]

One of the greatest challenges for widespread utilization of solar energy is the low conversion efficiency, motivating the needs of developing more innovative approaches to improve the design of solar energy conversion equipment. Solar cell is the fundamental component of a photovoltaic (PV) system. Solar cell's precise modelling and estimation of its parameters are of paramount importance for the simulation, design, and control of PV system to achieve optimal performances. It is nontrivial to estimate the unknown parameters of solar cell due to the nonlinearity and multimodality of search space. Conventional optimization methods tend to suffer from numerous drawbacks such as a tendency to be trapped in some local optima when solving this challenging problem. This paper aims to investigate the performance of eight state-of-the-art metaheuristic algorithms (MAs) to solve the solar cell parameter estimation problem on four case studies constituting of four different types of PV systems: R.T.C. France solar cell, LSM20 PV module, Solarex MSX-60 PV module, and SS2018P PV module. These four cell/modules are built using different technologies. The simulation results clearly indicate that the Coot-Bird Optimization technique obtains the minimum RMSE values of 1.0264E-05 and 1.8694E−03 for the R.T.C. France solar cell and the LSM20 PV module, respectively, while the wild horse optimizer outperforms in the case of the Solarex MSX-60 and SS2018 PV modules and gives the lowest value of RMSE as 2.6961E−03 and 4.7571E−05, respectively. Furthermore, the performances of all eight selected MAs are assessed by employing two non-parametric tests known as Friedman ranking and Wilcoxon rank-sum test. A full description is also provided, enabling the readers to understand the capability of each selected MA in improving the solar cell modelling that can enhance its energy conversion efficiency. Referring to the results obtained, some thoughts and suggestions for further improvements are provided in the conclusion section. [ABSTRACT FROM AUTHOR]

In this paper, dynamic analysis of a multi-battery dual mode charger, powered by a single solar array and suitable for lead-acid and lithium-ion cell-based batteries is presented. Each battery is interfaced to the solar array by means of a current-controlled buck power stage, operating either in constant power or constant voltage mode. Operation in former/latter charging mode implies regulating input/output voltage of the converter, which is a non-trivial situation since while feeding different batteries, all the converters share the same input terminals, connected to the solar array. It is revealed that when at least one of the batteries operates in constant power charging mode, open-loop instability occurs whenever converter input voltage is lower than maximum power point voltage of the solar array. Consequently, input voltage regulating controller must be designed to stabilize closed-loop dynamics for the worst case of instability, which is also derived. Moreover, it is shown that the dynamics of the converters operating under output voltage control are perceived as disturbances by input voltage control loop and must be properly rejected. Simple loop shaping design is proposed based on a PI controller, allowing stabilizing the system in case of worst case instability and rejecting output voltage control induced disturbances at the expense of non-constant, operating-point dependent closed-loop damping. [ABSTRACT FROM AUTHOR]

ABSTRACT The paper presents a simple approach to deriving I-V curves of photovoltaic panels and small arrays for arbitrary environmental conditions on the basis of three points of a single operating curve data and short current temperature coefficient only. The proposed method does not employ fitting of any type and is solely based on a numerical solution of a system of transcendental equations. The equations are expressed in a dimensionless form, simplifying both the solution and photovoltaic panel parameters' representation. The solution is used to find the values of normalized equivalent circuit elements for the available data and then perform an appropriate adjustment to obtain the operating curves for arbitrary conditions. The proposed method was applied to monocrystalline and polycrystalline commercial solar panels and was compared with both manufacturer-provided and experimentally measured operating curves to analyze the approach applicability and accuracy. Copyright © 2012 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]

Abstract: In this paper, a method of designing an optimally arranged solar array for converterless matching to a known linear load is proposed and compared to the classical Maximum Power Point Tracking method. Long-time performance of both methods is examined for three common types of loads under real weather conditions. Test results indicate that only in case of a pure resistive load the Maximum Power Point Tracking-based solar system advantage is undisputed. In case of a load represented by a voltage source with internal resistance, the long term energy productions of the system employing a practical Maximum Power Point Tracking operated converter is on a par or lower than the converterless system energy yield. [Copyright &y& Elsevier]