Search

By designing stator teeth using grain-oriented sheets (GO) and other parts still with non-grain-oriented sheets (NGO), the electromagnetic performance of the interior permanent magnet synchronous machine (GO-IPMSM) can be improved greatly. As the stator core of the designed GO-IPMSM is a hybrid core that is composed of two different silicon sheets, both the electromagnetic and mechanical performances are affected by the stator joint shape between GO and NGO sheets. Meanwhile, with the adoption of GO, the torque ripple of GO-IPMSM is increased though the average torque is increased as well. For reducing the torque ripple, optimizing the rotor barrier shape is an effective way. In this paper, the piecewise linear interpolation method is employed for establishing the stator joint shape between GO and NGO sheets, and the polynomial method is proposed to establish the rotor barrier shape. Through the analysis, it can be seen that the stator joint shape plays a strong role in affecting the mechanical performance of the GO-IPMSM, while the effect on the electromagnetic performance is weak. The genetic algorithm is used to optimize the rotor barrier shape for achieving high average torque and low torque ripple. Lastly, a quick and accurate efficiency map calculation method based on the Kriging model is proposed for GO-IPMSM with less finite element method (FEM) samples are required. [ABSTRACT FROM AUTHOR]

The effect of winding chording on five-phase synchronous reluctance motor (SRM) modelled in phase variables is presented. The stator winding configuration is shifted a pole pitch from a fullpitch configuration to a 54 degrees over-full-pitched configuration incorporating the effect of 3rd harmonic of the air-gap magneto-motive force in the inductance equations. The models are monitored on starting, synchronism, loading, faults and loss of synchronism. These are considered simultaneously with vector potential, rotor speed, air-gap flux linkage and winding current. The phase variable (analytical) models have been simulated by using MATLAB/Simulink software while ANSYS Maxwell software has been used to simulate the finite element model (FEM) of the motor for corresponding chording ranges for comparison on direct online starting (DOL). Under all conditions considered in the work, the detailed results are presented and very close similarity is observed between the analytical and the nearly ideal FEM model for all chording ranges and the similarity is enhanced with increase in chording angle. [ABSTRACT FROM AUTHOR]

SRMs have high torque ripples. Modifying the stator and rotor shape of SRMs is one of their methods to remove torque ripples. In this study, new rotor and stator geometries have been proposed for SRM. Performance characteristics are obtained and dynamic analyses are carried out for both novel and classical 6/4 SRMs. FFT analyses of the torque characteristics are also performed for the both SRMs. The changes in performance and the FFT results of torque characteristics are determined for both the current-controlled and uncontrolled operations in both SRMs. 23.60% and 15.20% improvements in torque ripples are achieved for the uncontrolled and current-controlled operations in SRMs respectively. When the FFT analyses are applied to the torque characteristics, the THD values are obtained as 21.19% and 8.31% in the uncontrolled and controlled motor current operations respectively. A 122 W three-phase 6/4 SRM simulation based on the MATLAB–SIMULINK environment is performed to validate the improvement of the torque ripple of the proposed model. [ABSTRACT FROM AUTHOR]

The Deflectable double-stator Switched Reluctance Generator (DSRG) has the advantages of simple structure, small volume and multi-dimensional operation. The DSRG and propeller are combined into the application of underwater power generation. With the help of the deflect ability of the generator, the efficiency is improved. Due to the uncertainty of ocean current direction and the structure of switched reluctance generator, the torque ripple is one of the important factors damaging the underwater generator. In order to effectively suppress the influence of torque ripple caused by generator operation, a method of adding pole shoes on the pole side of outer stator is proposed, so as to reduce the torque ripple. The propulsion structure running at different deflection angles is simulated. The torque and speed obtained before and after pole shoe optimization are input into the propeller model. The pressure and speed characteristics of the corresponding blade structure are simulated to verify the effect of optimization and the effectiveness of the power generation system. [ABSTRACT FROM AUTHOR]

With the development of power electronics technology, permanent magnet brushless DC motors have developed rapidly and are now widely used in electric vehicles, flywheel energy storage, rail transit, and other applications. The stator slot structure is one of the main factors affecting the performance of the motor. A low-power permanent magnet brushless DC motor was selected as the research object, and the finite element analysis method was used to study the effects of different slot and pole combinations and stator slot types on the cogging torque, reluctance torque, and back electromotive force of the permanent magnet brushless DC motor. The influence of the stator slot structure of the motor on the performance of the motor was analyzed, and the optimal slot-pole combination and stator slot type were determined. The results showed that the cogging torque of the 2-stage 24-slot motor was 14 mN·m, and the reluctance torque was 75 mN·m. The cogging torque and reluctance torque were the smallest, and the back electromotive force waveform was similar to a trapezoidal wave. The motor cogging torque of the pear-shaped round slot was the smallest, with a value of 460 mN·m, and the motor reluctance torque of the pear-shaped trapezoidal slot was the smallest, with a value of 1.2 N·m. The back electromotive force waveforms of the motors with four different stator slot types were similar. [ABSTRACT FROM AUTHOR]

In this article, a leaf spring insertion to the stator back iron is proposed to reduce vibration and acoustic noise in a switched reluctance machine (SRM). The back iron of the tooth tip is curved out and the material made up of carbon spring steel is placed to dampen the vibration due to radial force. A 6/4 stator/rotor pole SRM is designed and its natural vibration mode frequencies are determined through finite-element analyses. The optimal current waveform is applied to the SRM model using the multidisciplinary coupled simulation method to determine the radial force with the harmonic orders. In the final step, the proposed leaf spring architecture is optimized to achieve the most dampening for the effective radial force harmonic orders. The simulation and experimental results confirmed the effectiveness of the leaf spring insertion in reducing the noise and vibration in SRMs. [ABSTRACT FROM AUTHOR]

Fractional‐slot concentrated‐windings are appreciated for their simple construction, short end‐winding length, high copper fill factor, low cogging torque, good field‐weakening capability and fault‐tolerant ability. However, in comparison to the conventional distributed windings, the fractional‐slot concentrated‐windings are characterised with high space magnetomotive force (MMF) harmonics, which results in undesirable effects on the machine performance, such as localised core saturation, eddy current loss in the rotor and noise and vibration. In order to improve winding characteristics, several techniques have been developed recently. This manuscript introduces the 5 new winding topologies by using the general concept of stator slot shifting. It means that, in order to cancel undesirable MMF harmonics, by doubling (or tripling or even multiplying) the slot number and dividing the winding and then relatively shifting the winding by one (or more) slots, the undesirable harmonics have been eliminated effectively. The best choice is chosen according to the lowest amount of the MMF harmonic, highest value of winding factor and torque desirable characteristics. At the end, comprehensive comparisons for the designed synchronous reluctance motor (SynRel) equipped with proposed windings and also distributed winding are presented. The analytical study and 2D FEM analysis results show that it is possible to get an ideal low space‐harmonic winding topology, and consequently, a low torque ripple for these motors. [ABSTRACT FROM AUTHOR]

In this article, we deal with design considerations of a new ac hybrid-excitation permanent-magnet machine with axial stator. Due to the presence of an axial stator, the machine features a typical three-dimensional geometric structure and field distribution. A simplified reluctance-based network is developed to capture the main design features of the machine. The analytical equations are deduced relating the main geometric dimensions to the machine design criteria: speed, power, and flux regulation capability. The influence of key machine geometric parameters, i.e., radial/axial air-gap length, stack length, and bore diameter, on output power, flux density, and flux regulation capability is investigated. It is found that there is a design tradeoff between the machine power density and flux regulation capability. The d/q-axis inductance and its ratio, which has an influence on flux weakening capability and operation performance, is examined. Finally, a 6-pole/36-slot prototype is built. Intensive experimental tests are carried out to verify the machine characteristics. [ABSTRACT FROM AUTHOR]

A typical flywheel energy storage system (FESS) includes an electrical machine, a flywheel, and magnetic bearings, which are independent of each other. Therefore, the structure of FESS is complicated, which leads to the problems of high cost and low integration. This article presents a novel stator PM excitation solid rotor machine (SPE-SRM) for FESS, which integrates an electrical machine, flywheels, and a magnetic bearing. The design method of the SPE-SRM is presented specifically. First, the structure and operation principle of the SPE-SRM are illustrated. Second, the design and optimization of the flywheel-rotor are presented with considering of power, energy storage, and mechanical strength. Third, the magnetic equivalent circuit of the SPE-SRM is established to simplify the design. Besides, the armature reaction and leakage flux factor are investigated. Fourth, the performance indexes, including torque, suspension force, no-load back electromotive force (back-EMF), losses, and temperature rise are fully analyzed by the finite element analysis. Finally, a 22 kW prototype is manufactured and tested. The rationality of the concept and design is validated by experiments. The SPE-SRM has the merits of high integration, robust structure, and low cost, so it has the potential for wide application in FESS. [ABSTRACT FROM AUTHOR]

Due to high precision, high speed, and high fault tolerance capability, the linear switched reluctance motor (LSRM) is applied in digital control technologies as well as electronic switching devices. The LSRM is considered as a good substitute for conventional linear drive systems for long-way transportation. In this paper, a single-stator and double-stator longitudinal flux-type LSRM for high-speed transit system is proposed. Since the flux in the longitudinal arrangement is in the same alignment as the motion of the translator, the proposed system is easier to construct, mechanically stable with minimum eddy current loss. It also produces the magnetic flux along the direction of motion, which makes it highly suitable for high-speed linear transit application. The proposed conceptual LSRM differs from the conventional LSRM, in such a way that the active stator holds the excitation windings, while at the same time it acts as a translational body that moves over the stationary translator bed. The motor characterization is performed in ANSYS electromagnetic simulation tool, to determine the applied forces, coupling inductance, and strength of the magnetic field of the proposed LSRM for the traction propulsion system. The finite element analysis (FEA) is utilized here to analyze the modeled configuration, for verification of the design and performance prediction of the proposed LSRM. [ABSTRACT FROM AUTHOR]

This article proposes a new “switched lumped reluctance network”-based equivalent circuit for a switched reluctance motor (SRM) under saturation. The proposed circuit incorporates the effects of the position-dependent switching of the phase windings and changing position of the rotor with respect to the stator. This feature enables the analysis of non-uniform and dynamic variation of flux in motor iron sections along with that in the air gap and their effects on the phase current. The proposed model, thus, emulates the operation of an SRM, more truly, through an equivalent circuit approach. The accuracy of the proposed model is verified by comparing the analytical results of five different stator–rotor sets (having different air gaps and tooth angular widths) with the finite-element method (FEM) simulated results and found to be in excellent mutual agreement. The static and dynamic performance obtained using the proposed model has been validated by experiments on a four-phase, 1-kW, 300-V, 1000-rpm SRM. [ABSTRACT FROM AUTHOR]

Summary: Predictive control of stator currents is a model‐based technique needing an estimation of rotor currents, which are normally not measured. These currents affect the evolution of the stator currents and, therefore, also affect the predictions used by the controller. The usual procedure consists in correcting their effect by a simple feedback technique. In this article, the estimation of rotor currents is tackled based in the induction machine equivalent circuit. The proposed estimation procedure aims at improving the predictions with respect to the usual procedure. Simulation and experimental results are provided for the particularly demanding case of a multi‐phase induction machine, showing the superiority of the proposal. [ABSTRACT FROM AUTHOR]

In this study, radial forces that create noise, which is a fundamental problem in Switched Reluctance Motor (SRM), are investigated. Since radial force causes stator vibrations and noise caused by magnetic field, a new switched reluctance motor model with increased stator and rotor poles has been designed in order to reduce the radial force acting on the rotor poles. In addition, a structure with high torque and low leakage flux compared to conventional winding structure has been proposed for Switched Reluctance Motors (SRM). The windings of the designed SRM are placed in layers, insulated from each other. Rotor poles are formed to move on both sides of each phase winding. Thus, the flux that will occur in the phase windings axially completes its circuit from the stator poles and the rotor poles. This designed ARM model has been examined by Finite Element Method (FEM. The proposed motor geometry has been analyzed with ANSYS Maxwell-3D, which performs FEM-based solution), and parametric analysis with ANSYS-RMxprt. [ABSTRACT FROM AUTHOR]

Recently, model-based predictive current control (MB-PCC) has been presented as a good alternative to classical control algorithms in terms of simplicity and performance reliability. However, MB-PCC suffers from the high dependence on system parameters, which may deteriorate its performance under parameters variations. On the other hand, synchronous reluctance motors (SynRMs) are susceptible to suffer from inductances variations due to the magnetic saturation. Accordingly, in this article a new model-free predictive current control of SynRMs based on a recurrent neural network (RNN-PCC) is developed and proposed. The proposed RNN-PCC relies on the identification of the SynRM currents without considering any parameters. Simulation and experimental results show that both RNN-PCC and MB-PCC have similarly excellent dynamics, while better control performance and tracking errors can be achieved thanks to the proposed RNN-PCC. [ABSTRACT FROM AUTHOR]

Dc-field excited modular variable flux reluctance machines (VFRM) are passive salient-pole rotor and independent stator winding, which makes it suitable for aerospace applications. Fault-tolerant operation is commonly required to improve its reliability. Hence, the performance under winding open-circuit faults is analyzed and the fault-tolerant control strategy is presented to increase the output capacity in this article. First, the dc-rectified output voltages and power of the VFRM under both normal and open-circuit faults are derived. Then, phase angle control strategy of the fault-tolerant operation for a 12-slot-14-rotor-pole (12s14r) modular VFRM is proposed, where the control sequence is optimized to achieve the maximum output power of the generation system. Compared with the classical fault-tolerant method, a higher applicability of the proposed method in terms of the types of fault-tolerant operations can be achieved. The electromagnetic properties, including the armature current and the capacity of electrical power output, are analyzed with finite-element analysis. The effectiveness and feasibility of the proposed fault-topology and control strategy are verified by the 12s14r VFRM prototype in normal, fault, and fault-tolerant operation. [ABSTRACT FROM AUTHOR]

Slotting effect in electric machines reduces flux per pole that effect magnetic flux density distribution in the air gap which induces harmonics in magnetic flux density causing flux pulsation, that in turn generates dominant torque pulsation in the form of cogging torque and torque ripples. To overcome the abovesaid demerits, a novel outer rotor field-excited flux-switching machine (OR-FSFSM) with a combined semi-closed and open slots stator is proposed in this study. The developed OR-FEFSM offers a high-power factor, due to the utilization of the semi-closed slot for armature coils. The open slot stator structure was chosen for the field excitation coil, which effectively suppresses leakage reluctance that causes flux pulsation. Thus, the influence of torque ripples is reduced, and the average torque is improved. In order to investigate the effectiveness of the proposed OR-FEFSM, a detailed study of stator slot and rotor pole combinations are performed. Based on simplified mathematical formulation, 12S/7P (stator slot/rotor poles), 12S/11P, 12S/13P, and 12S/17P are the most feasible combinations. Finite Element Analysis (FEA) based on comprehensive electromagnetic performance is performed on each combination, and found that 12S/13P offers the highest average torque of 4.62 Nm, whereas 3.72 Nm, 2.72Nm, and 1.68 Nm average torque is offered by 12S/17P, 12S/7P, and 12S/11P, respectively. Based on the initial analysis, 12S/13P was considered for further analysis and optimized using JMAG built-in Genetic Algorithm (GA). Moreover, thermal analysis was performed, and the proposed design was compared with the conventional design. [ABSTRACT FROM AUTHOR]

This article focusses on power quality issues related with the operation of a wind energy conversion system employing a doubly fed induction generator (DFIG), integrated with a solar photovoltaic array, under unbalanced, and distorted grid conditions. The multiple-order DFIG electromagnetic torque ripples and grid active power ripples, resulting from the unbalanced and distorted grid, can be mitigated, however, at the cost of highly unbalanced and distorted currents. This article provides a possible solution towards a tradeoff by developing a flexible ripple minimization technique based on a cross-feedback extended second order generalized integrator for harmonics sequence separation (CextSOGI-HSS). The CextSOGI-HSS based current compensation enables a controlled minimization of ripple as per the customizable flexibility quotient. Furthermore, the current compensation technique employs an improved recursive least squares (IRLS) adaptive filtering algorithm for processing DFIG stator currents and local load currents. The IRLS algorithm improves grid currents harmonics spectra by filtering-out higher order harmonics from DFIG stator currents and nonlinear load currents, meanwhile, the effects of any load or stator currents unbalance on grid currents are also mitigated. Test results from a developed laboratory prototype confirm the efficacy of the presented flexible ripple minimization control technique. [ABSTRACT FROM AUTHOR]

This article proposes a multiobjective optimization design framework for a double stator brushless hybrid excitation motor (DSBHEM) to provide high torque, wide flux regulation ability and low torque ripple. The design variables are divided into sensitive level and insensitive level by sensitivity analysis. The response surface model (RSM) and nondominated sorting genetic algorithm 2 (NSGA2) are organically combined to generate a set of Pareto solutions for the sensitive level variables, from which the optimal values of the sensitive level variables are obtained. In addition, the optimal values of insensitive variables are obtained through single parameter scanning optimization, and a set of final optimal design variables are obtained. The electromagnetic performance of the initial design and the optimal design are compared with finite element analysis. Finally, a prototype is manufactured to verify the proposed concepts. [ABSTRACT FROM AUTHOR]

This article reveals the flux leakage design and modeling principle of a flux leakage controllable permanent magnet (FLC-PM) machine by considering driving cycles. The key is to obtain the relationship between flux leakage characteristics and multiple operating conditions. Based on the flux leakage controllable concept, an FLC-PM machine with an artfully designed flux leakage region is proposed. The design principle of the machine is investigated by analyzing the magnetic circuit of the machine in multiple operating conditions. The flux leakage factor is introduced to characterize the variable magnetic field in multiple operating conditions. On this basis, the mathematical model of the FLC-PM machine is deduced, and the driving characteristics of the machine are studied in detail. In order to evaluate the presented principle of the FLC-PM machine, a prototype is manufactured for experiments. Through the theoretical analysis and experimental testing, it is verified that the proposed principle is feasible and effective. [ABSTRACT FROM AUTHOR]

In this article, an integrated drive converter of segmented double-stator switched reluctance machine (SDS-SRM) with isolation and nonisolation charging capabilities for electric vehicle (EV) is presented. The proposed converter can not only reduce the number of the power switches, but also implement multiple operation modes. In nonisolation charging mode, the motor windings and existing power switches constitute a buck/boost converter to charge the battery. The appropriate rotor positions are obtained to achieve torque-free control, and the interleaved phase currents control method is introduced to reduce the charging current ripples. In isolation charging mode, the inner-stator is powered by the utility grid to drive the middle-rotor, and converts electrical energy into mechanical energy, while the outer-stator is operated in generation mode to convert mechanical energy into electrical energy. The SDS-SRM is served as a rotating transformer to transfer the electric power to charge the battery with the galvanic isolation function. A low power proof-of-concept prototype platform is built and experiments are carried out to verify the effectiveness of the proposed integrated drive converter and the corresponding control schemes. [ABSTRACT FROM AUTHOR]

In current engineering, the skewing slots approach is commonly used for permanent magnet synchronous motor (PMSM) to reduce torque ripple and electromagnetic vibration. However, this approach may limit the axial length of the motor and increase the manufacturing cost. This article studies a segmented rotor with different pole widths approach to mitigate torque ripple and electromagnetic vibration for PMSM, which has a lower implementation cost and facilitates mechanized production. The mapping relationship between geometric dimensions and torque performance is obtained, and the optimal dimensions are determined. An 8-pole/48-slot V-shaped PMSM is taken as the original motor, and the influence of engineering error on the torque performance of the presented approach is discussed. The electromagnetic performances and vibration responses of the motor with the presented approach are compared with that of the skewing slot motor to verify the effectiveness of the presented approach. Finally, prototypes are built, and intensive experimental tests are carried out to verify the analysis and comparison. [ABSTRACT FROM AUTHOR]

This article proposes a hybrid analytical modeling procedure for the performance parameter estimation of synchronous reluctance machine, including its operation in the region of magnetic saturation. The proposed model better estimated the torque profile through improved translation and stepped transition of rotor flux barriers. The non-linear operation is simulated by considering the global saturation and estimating the machine’s operating point on the magnetization curve of the core material. The procedure formulation focuses on improving the accuracy and rapidness of the iterative design process. The obtained results are validated against an already established design analysis technique, finite-element analysis, and the frequency spectrum analysis of practical machine results. With the improved accuracy and the least requirement of simulation runtime and computational resources, the modeling procedure can be utilized as an initial design iteration tool. [ABSTRACT FROM AUTHOR]

This work presents an adaptive feed-forward current fed battery-supported solar water pumping system using a synchronous reluctance motor (SYRM). It incorporates the impact of cross saturation in real time with the position sensorless vector control technique of SYRM. Moreover, a continuous estimation of direct axis inductance (Ld) is incorporated to ensure saturation in SYRM. The burden of the DC link voltage PI controller is relieved by the feed-forward term of an adaptive battery current, which is calculated from the photovoltaic (PV) array power, estimated output power and the estimated motor efficiency. A DC-DC boost converter is used for maximum power point tracking (MPPT) of the solar photovoltaic array. A voltage source inverter is employed to control the SYRM-pump drive, and to charge/discharge the battery, a bidirectional DC-DC converter is used. The system provides a cost-effective solution for an uninterruptable and rated discharge of the water supply. The solar PV array behaves as a primary energy source, whereas battery is used as a backup source and is charged by PV array when pump operation is suspended or operating at a lower rating. The satisfactory performance of developed system is verified through experimental results taken on the developed laboratory prototype. [ABSTRACT FROM AUTHOR]

In this article, a circulating-current-excited switched reluctance generator system using a standard diode rectifier is proposed and examined. It features a dc power source connected in series with the ring-connected windings, which provides the dc-bias current as the excitation current in the windings. Using a series-connected dc power source, a dc-bias current is easily realized in the ac winding. Compared with the existing machine having dc-bias in the ac winding, the proposed generator can provide dc power with a standard diode rectifier. Less active legs and no rotor position sensor are needed for the control of the circulating current of the proposed generator, which increases the reliability of the generation system. The system configuration and the operation principle are introduced in detail. Then, the electromagnetic performance of the proposed generation system is analyzed at both open-circuit and load conditions. The asymmetric current distributions are deduced and verified by the simulations. At last, the prototype is tested under varied operation conditions and the experiments agree well with the analysis. [ABSTRACT FROM AUTHOR]

Multiphase machines with a prime number of phases (five and seven) have shown better torque density than machines with other phase numbers. Unfortunately, these machines require a special stator design. Hence, this article proposes general rewinding techniques to obtain a five-phase winding from the existing standard three-phase stator frames. The proposed rewinding techniques are applied to construct a five-phase star-connected synchronous reluctance machine (SynRM 1) and a novel combined star-pentagon winding (SynRM 2). Simple mathematical formulations are introduced to compute the equivalent winding factor. The performance of five-phase SynRMs is analyzed using two-dimensional Ansys Maxwell transient simulations under the same copper volume for both healthy and faulty cases. SynRM 1 and 2 provide 6.56% and 13.35% higher torque compared to the three-phase SynRM at rated current and at optimal current angle. The torque ripple is decreased by 17% and 30%, respectively. Moreover, SynRM 1 and 2 offer a better performance at the faulty case; e.g., at one phase opened, the average torque of SynRM 1 and 2 is 82% and 108% higher compared to the three-phase SynRM. In addition, the torque ripple is reduced by about 63% and 81%. Finally, experimental results are done to validate the proposed winding techniques. [ABSTRACT FROM AUTHOR]

Vernier reluctance machine (VRM) with dc field coils in stator is a competitive rare-earth-free design for variable-speed industrial applications due to its robust structure and controllable excitation, while its torque density is relatively disadvantageous. To address this issue, this article proposes a new armature winding design method for VRM with dc field coils across two stator teeth. The key is to break the traditional winding design principle based on the flux modulation effect of fundamental dc field harmonic, and instead, reconstruct a novel harmonic winding to enhance the utilization factor of the modulated high-order dc field harmonics arising from the unique magnetomotive force distribution of dc field coils across two stator teeth. By this means, the torque density can be improved by 75.6% against the existing poor counterpart. In this article, the machine structure and operation principle are introduced, with emphasis on the high-order dc field harmonics distribution rule and its influence on the armature winding design. By finite element design and optimization, a comparative study is performed to evaluate the electromagnetic performance of VRMs using two different winding configurations with variable slot pole combinations. A prototype is fabricated and tested, and the results agree well with finite element analysis, which verifies the feasibility and advantages of the proposed winding design method. [ABSTRACT FROM AUTHOR]

This article presents a new type of double stator swing rotating permanent magnet spherical motor (DSSRPMSM), which can realize swing, rotation, and helical motion and is used in industrial robots, gyroscopes, satellite communications, and other fields. The proposed spherical motor consists of two stators and a hollow rotor with permanent magnet (PM) poles on its inner and outer surfaces. Compared with most spherical motor with hollow coil and traditional PM synchronous motor, the structure of the motor is different and novel, and it is difficult to find a more perfect design theory and method. Thus, this article introduces the new idea of motor design in detail. First, the structure and working principle of the motor are introduced, and the original design of the motor is carried out. The 2-D rough estimation and 3-D FEM accurate simulation calculation are carried out, and the electromagnetic characteristics of the motor are obtained, including magnetic flux density distribution, torque, and loss. The simulation results meet the design specifications of the motor. A prototype was built and tested. The experimental results are in good agreement with the 3-D FEM analysis. The design method provides a theoretical basis for the design of this kind of spherical motor. The research results lay a foundation for the subsequent optimization of the motor. [ABSTRACT FROM AUTHOR]

A new partitioned stator field modulation machine (PSFMM) with H-shape permanent magnet (HPM) excitation (HPM-PSFMM) is proposed, which is evolved from the conventional flux-switching machine (FSM) and flux-reversal machine (FRM). The proposed HPM-PSFMM combines the merits of high reliability and good heat dissipation characteristic. In addition, it exhibits high torque production with low torque ripple. Based on the theory of electrical machine operation, the FSM and FRM can be transformed into PSFMM with interior permanent magnet (IPM) and surface-mounted PM (SPM) excitation by changing the position of PM excitation, respectively. It benefits to improve space utilization and increase slot area for a large number of armature windings. For reducing the flux leakage and enhancing the flux density in air gaps, the IPM and SPM excitation are combined into HPM excitation. The iron-pole rotor between the inner and outer stators acts the role of modulator to modulate the magnetic field excited by HPM excitation to couple with the armature reaction for converting electromechanical energy. The evolution process, operating principle, and key design parameters of the proposed HPM-PSFMM are presented. Finally, using the finite element analysis (FEA), it can be proven that the proposed HPM-PSFMM has the merits of high torque production, low flux leakage, low total harmonic distortion (THD), and low torque ripple when compared to other stator-PM machines, which is a desirable choice for high stability applications. [ABSTRACT FROM AUTHOR]

The circumferential and axial widths of permanent magnet (PM) pole and E-shape stator pole of linear rotary motor with interlaced PM poles are very influential to the back electromotive force (EMF) and the flux leakage analysis is complex, which causes difficulty in optimization of the motor structure. One of the key issues in optimization design is to calculate the flux leakage accurately. In this article, the main flux and side flux variation laws of stator pole are derived by analytical method. The flux leakage can be divided into the flux leakage between the PM and the mover, flux leakage on the stator tooth tip, and the flux leakage between the adjacent PM poles and stator pole. The 3-D flux leakage calculation model is built, which is suitable for the calculation of magnetic flux based on different motor operating principles. Then the rotational and rectilinear back EMFs are calculated by analytical method, which are consistent with the results analyzed by 3-D finite element method. [ABSTRACT FROM AUTHOR]

Switched reluctance generator is widely used in the field of wind power generation. The efficiency of generators was usually related to the deviation angle. Compared with the single stator type switched reluctance motor, these dual-stator type switched reluctance motor models have the advantages of high accuracy, fast response and small size. An optimization method based on fuzzy algorithm and parameter scanning is proposed to improve the low speed performance of high efficiency generator. Taking the maximum output power, system efficiency and torque smoothing coefficient of DDSRG as the optimization goals, the effects of the turn-on angle, turn-off angle and reference current on the optimization goal are analyzed. The multi-objective optimization function is constructed, and the optimal combination value is obtained. The experiment proved that the parameter-controlled multi-objective optimization method could effectively improve the comprehensive performance of DDSRG in low-speed operation state. [ABSTRACT FROM AUTHOR]

This article deals with the lookup table (LUT) less sensorless control of synchronous reluctance (SyR) machines at zero and low speeds, where LUT-less stands for avoiding the use of flux-map LUTs or other predetermined machine parameters. The new signal-injection-based control scheme called the locus of incremental saliency ratio tracking is presented, where a pulsating high-frequency voltage component is used for position tracking and a second rotating signal-injection is dedicated to online estimating the incremental saliency ratio. A trajectory of constant incremental saliency ratio is used for torque regulation, resulting in stable control at all operating conditions, including overload. This despite the effect of cross-saturation, which is known to introduce position error and harm the control stability progressively with the load. The proposed scheme is validated experimentally on a 1.1-kW SyR machine test bench. Alternative LUT-less torque control laws are investigated, and their stability limits put in evidence using convergence analysis and experiments. [ABSTRACT FROM AUTHOR]

Multiphysics analysis and experimental validation of acoustic noise reduction in a high pole count, high power, switched reluctance machine (SRM), through skewing are explored in detail in this work. An iterative optimization strategy covering electromagnetic, structural, and thermal domains is proposed to investigate the effect of different skewing methods and angles on a 24-stator slot/16-rotor pole (24/16) SRM rated at 100 kW. The contributions of this work are twofold. First, electromagnetic impact, considering average torque, torque ripple, radial and tangential air gap forces, of symmetric and asymmetric skewing on stator and rotor is studied in this work. Second, the impact of skewing methods on acoustic noise and vibration performance is studied and presented in detail. The study reveals that skewing both the stator and rotor by the same amount has superior electromagnetic performance over other types of skewing. Multiphysics simulations conducted, predict a 10.5 dBA reduction in the acoustic noise, compared to a baseline design with no skew, for an optimized rotor-stator skewing angle of 13.75°. Finally, 100 kW prototypes of the baseline and the optimized skewed SRM were constructed and subjected to wide speed range testing. Simulation and test results closely follow each other and validate the effectiveness of the proposed skew design in mitigating acoustic noise and vibration in high pole count SRMs. [ABSTRACT FROM AUTHOR]

A modified configuration for Permanent Magnet Assisted Synchronous Reluctance Motors (PMaSyRM) is studied in this paper. Conventionally, the PM materials are inserted in the flux barriers region of the rotor. Consequently, the PMs sizing parameters will be restricted to the available space that may limit the efficient use of PMs benefits. In this study, a portion of the rotor structure is replaced with an Interior PM (IPM) rotor so that an axially segmented integration of IPM and SyRM is obtained. Thus, the PMs design is performed specifically in the IPM segment independent of the SyRM scheme, while the SyRM segment remains PM-less. The main motivation of this concept is to improve the contribution of the PM material in the total torque as well as utilizing the special property of the proposed rotor configuration for pulsating torque reduction. A computationally cost-effective algorithm is proposed for the optimal design of IPM-SyRM motor by which a low-power design is carried out for a lightweight electric vehicle. The results for torque profile characteristics, PM volume, power-factor, and efficiency are compared with a conventional PMaSyRM that has been optimally designed as the reference case. Finally, a prototype is constructed to verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

In this paper, a novel six-phase outer rotor induction motor equipped with pseudo-concentrated windings is introduced as a robust, reliable, and low-cost solution. Multiple aspects of the proposed motor structure have been investigated such as a design algorithm and an analytical modeling based on the modified winding function considering the skew effect. The effect of using variable number of turns for the coils has been examined on the pseudo-concentrated windings. An appropriate optimization problem has been also defined to maximize the power factor and efficiency and to minimize the output torque ripple. The designed motor has been fabricated to verify the accuracy of the design procedure with an analytical model and a finite element analysis. Experimental results show superior performances for the designed motor. [ABSTRACT FROM AUTHOR]

The torque ripple of a switched reluctance motor (SRM) should be taken into account, as it can have negative effects on a connected gearbox and/or load. In this paper a concept and two realization methods for the reduction of the torque ripple are presented. An optimized alignment of the active elements of the stator leads to a reduction of this torque ripple. The first method proposed here is a four-fold segmented motor, which can reduce the torque ripple by 37.3 %. This can be achieved by segmentation in combination with a clever arrangement of active elements. However, this increases the number of necessary inverters, which increases redundancy and therefore leads to more security. A second method of achieving an equal reduction can be obtained by using a “double stator” motor. In this configuration both stators can be powered together. With this concept, the number of converters is halved compared to the first mentioned solution. This saves electronic components and thus reduces the effort. All results referred to in this article are obtained by simulation, or measured on a prototype. [ABSTRACT FROM AUTHOR]

With the adoption of 3D magnetic flux material and global ring windings, permanent magnet transverse flux machine (PMTFM) with soft magnetic composite cores can output relatively high torque density and only requires easy manufacturing process. For the PMTFM, there are two ways to put the permanent magnets (PMs). One is to put the PMs on the rotor side which is the traditional rotor PM TFM and the other is to put the PMs on the stator side which is the stator PM TFM. In this paper, the design methods and operation principle for both kinds of PMTFM will be presented and discussed. Four different TFMs (benchmark rotor PM TFM with NdFeB, stator PM TFM1 with ferrite magnet and stator PM TFM2 and TFM3 with NdFeB) have been designed, and the magnetic parameters and the main performance will be comparatively studied to show the main difference between stator PM TFM and rotor PM TFM. It can be seen that the stator PM TFM has better performance, and the stator PM TFM1 with ferrite magnets can have the same torque ability as that of the rotor PM TFM with NdFeB magnet but with very low material cost. With the adoption of NdFeB, the stator PM TFM2 can have two times higher torque ability than the rotor PM TFM, and the stator PM TFM2 can have the same torque ability as that of rotor PM TFM but with much smaller volume. As for the power factor and efficiency, it can be seen that the adoption of ferrite magnet will reduce both of them, and there is no much difference for the place where the PMs are installed. [ABSTRACT FROM AUTHOR]

This paper investigates the accuracy of rotor‐locked transient‐response (RLTR)‐based vibration model for switched reluctance machines (SRM). RLTR is stator vibration stimulated by abrupt change of radial force when turning off one phase of SRM with rotor being locked, the total vibration of SRM can be modelled as linear superposition of RLTR series. An electromechanical model is built to clarify the generation of SRM vibration, it is revealed that some velocity‐depend terms in electromechanical model would be neglected when rotor is locked, it leads to inevitable difference of RLRT between rotor‐locked condition and rotational condition, the difference is illustrated through multi‐physics simulation. A harmonic radial force model is proposed to quantitatively evaluate the accuracy of RLTR‐based vibration model, radial force spectrums with locked rotor and rotational rotor are compared to predict relative error between RLTR‐based vibration and actual vibration. The influence of turn‐off angle and velocity on accuracy of RLTR‐based vibration model is also analysed. The accuracy of RLTR‐based vibration model is evaluated through experiment on 3‐phase 12/8 SRM, the results showed that: (1) the accuracy of RLTR‐based vibration model is impacted by turn‐off angle and velocity; (2) relative error between RLTR‐based vibration and actual vibration can be predicted using harmonic radial force model. This paper illustrates the generation mechanism of modelling error for commonly used RLTR‐based vibration model of SRM, the proposed error prediction method could lead to improved accuracy on SRM vibration model through error compensation. [ABSTRACT FROM AUTHOR]

This article proposes a nonlinear controller based on feedback linearization (FL) for synchronous reluctance motor (SynRM) drives which takes into consideration the magnetic saturation. The proposed nonlinear FL control based control technique has been developed starting from the theoretical definition of an original dynamic model of the SynRM taking into consideration both the self- and the cross-saturation effects. Such a control technique permits the dynamics of both the speed and axis flux loops to be maintained constant independently from the load and the saturation of the iron core in both constant flux and variable direct axis flux operating conditions. Finally, sensitivity of the performance of the proposed FL control versus the variation of the main motor parameters has been verified. The proposed technique has been tested experimentally on a suitably developed test setup. The proposed FL control has been further compared with the classic field-oriented control (FOC) in both constant flux and variable flux working conditions. [ABSTRACT FROM AUTHOR]

This article proposes a new magnetic model self-identification technique for synchronous machines to build the flux-map look-up tables. Provided the shaft is free to turn, an alternating self-acceleration and deceleration sequence is envisaged for identification without a dedicated experimental rig or additional hardware. With respect to previous works, the stator flux and the stator resistance are adapted online during the run, thus eliminating the need for postprocessing and the sensitivity to winding temperature variations during the test. Experimental validations on a 1.1-kW synchronous reluctance and a 11-kW permanent-magnet-assisted synchronous reluctance motors are provided. [ABSTRACT FROM AUTHOR]

Linear Motors are potential candidates for replacing traditional rotary motors in high-speed transit systems. Linear Switched Reluctance Motor (LSRM) is the widely researched motor for such applications. This paper presents a design for linear switched reluctance motor (LSRM) with an improved propulsion force profile. The proposed motor consists of moving translator for direct drive transmission, without the use of mechanical gears. The stator contains a split-teethed stator structure. The proposed motor has more translator teeth than stator teeth. This paper includes a new design methodology for the proposed combination of stator and translator. The motor is designed and analyzed using 3-D finite-element method (FEM). The proposed motor has been optimized using a parameter-based cumulative deterministic optimization algorithm (PBCDOA) for further improving the force profile. The FEM results demonstrate the effectiveness of the design procedure and better force performance of the proposed topology. [ABSTRACT FROM AUTHOR]

Signal-injection sensorless control for low speeds region are usually assisted with compensation techniques to support the heavy load operations beyond rated conditions. For the standard $d$ -axis pulsating voltage injection, this article analyzes the prospect of using $q$ -axis current-model flux instead of the $q$ -axis current for decoupled position estimation. Through convergence analysis, the feasibility of operation at overload is evaluated for the decoupled scheme against the state-of-art compensation technique and is shown to be a promising candidate for its simplicity and the lack of preprocessing of flux-map. All claims are experimentally validated on a 1.1 kW synchronous reluctance machine test-bench. [ABSTRACT FROM AUTHOR]

A linear switched reluctance motor (LSRM) is designed for electric propulsion application in a Magnetically Levitated (Maglev) train with the base speed of 7.6 m/s and operating at a maximum of 27.8 m/s. In such high‐speed LSRMs, windage loss is one of the key issues of concern. Usually, windage loss accounts for approximately 0.5% below the base speed, 20% above the base speed, and 45% at higher speeds of the total loss of the LSRM. One of the many parameters affecting this windage loss is the stator slot profile. This research work studies about different stator slot structures, thereby aiming to reduce the windage loss through computational fluid dynamics analysis. Furthermore, experimental testing of the LSRM is also done to verify the simulation results. [ABSTRACT FROM AUTHOR]

Performance achievable in sensorless control of electrical drives strictly depends on the adopted synchronous machine. The combination of cross-saturation and saliency, both dependent by the current load and the rotor position, makes always the position estimation afflicted by an estimation error. When the machine is highly saturated, the sensorless control can even diverge resulting in a useless drive. Thus, it is of primary importance to know in advance the convergence region of the sensorless drive, i.e., the operating points, where the motor can be successfully controlled without a position sensor. The aim of this article is to show how to compute the estimation error, the saliency, and the convergence region (hereafter called self-sensing capabilities) starting from the flux linkages maps or, more generally, from the incremental inductances. The dependence on the rotor position is also considered. Finite element simulations and experimental measurements validate the proposed model. The code used to compute the self-sensing capabilities is available as an open source package. [ABSTRACT FROM AUTHOR]

This paper proposes an automatic design method of typical parameters such as number of phases, number of poles, stack thickness, stator outer diameter, rotor outer diameter, and number of turns of a switched reluctance motor from the requirement of the N‐T characteristic. In particular, a specific parameter related to the magnetic saturation is defined in order to arbitrarily determine how much to use the magnetic properties of the iron core material. In the proposed method, the typical motor parameters in order to realize a miniaturized volume which satisfies an input N‐T characteristic are obtained by setting the parameter related to magnetic saturation, maximum electrical frequency, maximum current density, maximum copper loss, conductor slot fill factor, magnetic properties of material, and input voltage. The designed motor is analyzed using the Finite Element Method (FEM) in order to validate the proposed method. [ABSTRACT FROM AUTHOR]

In order to solve the coupling between torque and suspended force of the traditional bearingless switched reluctance motor (BSRM), a bearingless switched reluctance motor with hybrid-rotor (HBSRM) is proposed in this paper. The HBSRM discussed in the paper has a twelve-pole stator and an eight-pole hybrid-rotor composed of a cylindrical rotor and a salient rotor. The magnetic pulling force between cylindrical rotor and stator is used to independently levitate the shaft, and that between salient rotor and stator is used to separately rotate the rotor. So, the HBSRM not only breaks the restriction of the effective output region between torque and suspended force in the traditional BSRM, but also facilitates the decoupling algorithm design and simplifies the levitation control of this bearingless motor. Firstly, the topology, operating mechanism and mathematical model of the proposed HBSRM are introduced respectively. Then the no-load decoupling control and torque ripple of the traditional BSRM and HBSRM are compared. Moreover, the load decoupling control characteristics of HBSRM are presented and verified by simulation analysis. [ABSTRACT FROM AUTHOR]

This article investigates the design methods and performance optimization of segmented-double-stator switched reluctance machine (SDS-SRM). First, two segmented U-shaped single-stator SRMs are introduced, including inner-rotor and outer-rotor constructions. In order to enhance the torque and power density, these two kinds of single-stator SRMs are combined together to constitute an SDS-SRM. Then, the relationships of torque ripple coefficient with the mechanical offset angles of the inner and outer rotor teeth are investigated to obtain the optimal rotor structure, and the corresponding conduction phase sequences for double-stator excitation mode are also analyzed. Furthermore, the flux distributions of the inner and outer stators with different coil magnetic polarities configurations are researched, and it reveals that the phase windings both on inner and outer stators with NSSNNSSN polarities have better magnetic field decoupling characteristics. To evaluate the final topology of the proposed SDS-SRM, the static magnetic characteristics and dynamic performances are presented. Finally, the SDS-SRM prototype is manufactured and tested to validate the theory and simulation analyses. [ABSTRACT FROM AUTHOR]

Stator and rotor cores of interior permanent magnet (IPM) motors are usually saturated, and the saturation distribution and saturation depth vary with the stator current. Also, their rotor structures are complex; hence, the saturation cannot be accurately reflected by a saturation factor. These considerations lead to the existing equivalent air-gap length models of induction motors and inset permanent magnet (PM) motors no longer suitable for IPM motors. Therefore, based on the consideration of stator and rotor saturation, this article proposes the equivalent air-gap length model of IPM motors expressed by magnetic potentials on the stator inner surface and the rotor outer surface. The proposed equivalent air-gap length model can accurately reflect the influences of complex structure and severe saturation of IPM motors. Compared with the existing models, the proposed one is no longer uniquely determined by motor structure parameters; it is also a function of stator current and rotor position. Furthermore, the obtained equivalent air-gap length model is combined with the winding function and the modified winding function to solve the inductances under different stator currents and different rotor eccentricity states. Finally, the proposed method is verified by both finite element analysis (FEA) and experiments. [ABSTRACT FROM AUTHOR]

This article employs grain-oriented (GO) silicon steel in an axial-flux permanent magnet (AFPM) machine to improve its torque and efficiency. Rolling direction of the GO material have been studied to ensure the machine’s main magnetic flux passes through the easy magnetization direction. Based on the study of the electromagnetic characteristics of AFPM machine, GO silicon steel is laminated to form a stator according to a certain lamination direction. The torque and efficiency of the proposed machine with GO material shows an increase in comparison with that of the conventional non-oriented (NO) silicon steel machine under identical conditions. In addition, an equivalent magnetic circuit model is established to illustrate little difference of electromagnetic property under no-load condition for the yokeless stator AFPM using two kinds of silicon steel sheet. Furthermore, a AFPM machine with stator yoke is also established to highlight the superiority of GO in the application of the AFPM machine with yokeless stator. [ABSTRACT FROM AUTHOR]

Synchronous reluctance motors show nonlinear behavior in the high torque region due to core saturation, especially on the $d$ -axis. In this study, the maximum torque per ampere (MTPA) solution is sought in the mathematical frame. First, flux linkage data are obtained from finite element method, and fitted as the plane functions of currents by the least square method. Thereafter, the inductances are derived as binomials in $i_d$ and $i_q$. These analytic expressions of inductances are used in deriving a necessary condition for the MTPA, and constructing an on-line MTPA control method. The effectiveness is verified through simulation and experimental results. [ABSTRACT FROM AUTHOR]