Search

Partial discharge (PD) is the main factor that can cause failure of the cold dielectric insulation system of superconducting cables. Nine insulation model cables with different insulating materials and wrapping styles are prepared. PD experiments under liquid nitrogen and room temperature are carried out on these model cables. Assuming that the lifetime of superconducting cable is 35 years, 40 thermal cycles from 77 –323 K are carried out on three model cables. Experimental results show that the PD is 100 times lower in liquid nitrogen than at room temperature for both polypropylene-laminated paper (PPLP) and polyimide (PI). Compared with model cables that used PI, the ones that used PPLP show much higher inception electric field. And no decay in partial discharge inception electric filed (PDIE) is found during the thermal cycles. The study will be helpful to the insulation system design for superconducting cable. [ABSTRACT FROM AUTHOR]

Abstract: Poloidal Field (PF) coils, made of CICC (Cable-In-Conduit Conductors), are the most important part of ITER (International Thermonuclear Experimental Reactor) superconducting magnet system. The structure of superconducting magnet system in ITER and the CICC are introduced. The main factors influenced the cabling of the superconducting cable for CICC is discussed. Analyzed the outer diameter controlling technique and the relationship between ac loss and structure parameters of the superconducting cable. The technique route of cabling has been established. Especially, the technique of dies setting for shaping+multi-rolling compacting dies+half-dies for diameter keeping is explained in detail, which can efficiently control the diameter and the cabling quality of the superconducting cable, without injury to strands line. The technical parameters for cabling is fixed and one 765m long dummy cable and one 115m long superconducting cable of CICC for PF coil is manufactured successfully for ITER the last. [Copyright &y& Elsevier]

The new energy revolution which will be dominated by renewable energy will need to develop a corresponding new power grid. Based on the characteristics of renewable energy resources, and the stability problem of AC network, it was proposed that the DC-based transmission grid should be developed in the future. The high Tc Superconducting (HTS) power cable will be a competitive candidate for large-capacity power transmission of renewable energy. In this paper, the progress of the development of a 360 m/10 kA HTS DC power cable is presented, and the prospects of HTS cable is discussed. [ABSTRACT FROM PUBLISHER]

With the increasing depletion of fossil fuels and growing environmental pressure, the mankind has got known the need to vigorously develop the renewable energy and the energy-saving technology. The high Tc superconducting (HTS) power technology will be very helpful to enhance the stability, reliability, and efficiency and transmission capacity of the power grid which would be dominated by the renewable energy. In this paper, we will report the installation and operation of a 10 kV HTS power substation which includes a 75 m/1.5 kA HTS power cable, a 10 kV/1.5 kA HTS fault current limiter, a 1 MJ/0.5 MVA high Tc SMES and a 630 kVA/10 kV/0.4 kV HTS power transformer. [ABSTRACT FROM PUBLISHER]

• The temperature distribution of an energy pipeline is simulated and tested. • A simulation model of the energy pipeline principle prototype is proposed. • The factors and laws that affected the temperature distribution are obtained. • An empirical formula to calculate the outlet temperature is achieved. Superconducting DC energy pipeline is an energy channel that simultaneously transmits electrical energy as well as the liquid fuel. It improves the efficiency of energy transmission and reduces the overall cost by cooling high-temperature superconducting DC cables with the low-temperature liquid fuel, such as liquid hydrogen, liquefied shale gas, and liquified natural gas (LNG). In order to properly design this, it is very important to know the temperature distribution along the pipeline, which is yet to be carried out by the researchers. In this paper, a 10 m energy pipeline with LNG cooling and having a concentric nested structure is simulated and tested experimentally. The simulation results of the temperature rise along the pipeline were in good agreement with the experimental results. The effect of various parameters on the pipeline temperature were also obtained. Finally, based on the theoretical equations and simulation results, an empirical formula is proposed to calculate the temperature at the outlet of the energy pipeline. [ABSTRACT FROM AUTHOR]