Search

The KSTAR superconducting magnetic coils, which are made of cable in-conduit conductor (CICC), maintain a superconducting state with forced-flow supercritical helium (4.5 K, 5.5 bar). During current changing of the superconducting magnetic coils, AC losses are generated in the CICC due to dI/dt, and the heat generated from the loss is removed by high heat capacity supercritical helium. At the same time, reversed flow of the helium occurs due to a rapid increase of the helium temperature and momentary changing of the pressure inside the CICC. This phenomenon has been detected in all of the poloidal field (PF) coils, especially in the upper (U) and lower (L) PF1 ~ PF4 coils. The maximum change of the magnetic field in the PF1UL ~ PF4UL coils is located near the inlet and outlet of the helium cooling channels, and that of the PF5UL ~ 7UL coils is located at the center of the cooling channel. The temperature variation at the helium inlet was always measured to have a time delay after each shot. In the PF1 coil tests, it was measured to have a delay of 26 sec. During the first plasma campaign, this phenomenon was more severe in the case of all PF coils operating together than for a single PF operation. In this paper, we investigated the thermal-hydraulics of this phenomenon. [ABSTRACT FROM AUTHOR]

The function of the current feeder system (CFS) is for conducting large currents from the power supplies to the KSTAR superconducting (SC) magnets. The CFS consists of SC bus-lines, joints, and current leads. The bus-line conductor is a circular cable-in-conduit conductor (CICC), which consists of a 4.5 mm thick stainless steel 316L seamless pipe containing 324 strands of chrome coated NbTi superconductor and 243 strands of OFHC. The ends of the CICC are assembled with specially designed lap joints. The joining resistance is controlled to less than 2.5 nano-ohm to minimize Joule heating. The outer surfaces of the CICC were electrically insulated up to 15 kV with jackets made of Kapton film and prepreged E-glass tape. Helically wrapped conducting fiber was used to measure the voltages of bus-line quenches. Two pairs of prototype brass leads for poloidal field (PF) and toroidal field (TF) coils have been fabricated and tested up to the currents of 26 kA for the PF leads and 35 kA for the TF leads. The test results satisfied all the requirements so that all 18 leads were manufactured and assembled on site. This paper will describe the detailed manufacturing progress and commissioning results of the KSTAR CFS. [ABSTRACT FROM AUTHOR]

KSTAR (Korea Superconducting Tokamak Advanced Research) superconducting magnet consists of a CICC (Cable-In-Conduit Conductor) and is cooled down less than 5 K using supercritical helium. The length of CICC is 610 m for TF coil and maximum about 2,500 m for PF coil respectively, especially the cooling channel is about maximum 300 m in PF coil because of continuous winding scheme. There are many cooling channels in KSTAR coils especially 84 channels in TF magnet system and 100 channels in PF magnet system. Flow imbalance affects cool down of magnet and leads to a difficulty of flow control. The pressure drop between CICC terminals has a close relationship with CICC hydraulic characteristic, helium refrigerator's performance and efficiency. The friction factor which is a representative parameter can be obtained under cryogenic operation condition. We attempt to find out the friction factor of KSTAR CS and PF CICC according to the test result of KSTAR CSMC (Central Solenoid Model Coil) 2nd campaign and compare the results with previous tests. The hydraulic characteristics of KSTAR superconducting magnet system like mass flow distribution, friction factor in conductor, pressure drop and etc during CSMC test and initial commissioning of KSTAR are presented. We can confirm the KSTAR CICC's unique hydraulic behavior in states of cool down and current charging period. Also, we expect that measured data will help to operate KSTAR and be a reference for thermo-hydraulic simulation. [ABSTRACT FROM AUTHOR]

An in-situ measurement of the magnetic field generated by the assembled superconducting magnet coils was held by using precision Hall sensors during the commissioning of the Korea Superconducting Tokamak Advanced Research (KSTAR) device. This was done in order to investigate the magnetic influence of Incoloy 908, which is the jacket material for the cable-in-conduit conductors (CICCs) of the Nb3 Sn coils. After the PF coils were discharged from 1 kA the vertical remanent field at the plasma center was more than 10 G, while the TF coils were not energized. The vertical magnetic field generated by the PF coils had a discrepancy of up to 50 G between measurement and the calculation assuming no magnetic influence of Incoloy 908. Thus, non-negligible ferromagnetism was identified and attributed to Incoloy 908. In contrast, most of the hysteresis observed in the magnetic measurements was eliminated when the Incoloy 908 of the TF windings was saturated by the TF coil charging. [ABSTRACT FROM AUTHOR]

The KSTAR components requiring cryogenic helium coolant for superconducting magnet operations are connected to the helium refrigeration system (HRS) through the helium distribution system (HDS), the final helium distribution station. Twenty eight cryogenic valves including 4 quench protecting valves, many sensors such as temperature sensors, pressure transmitters, and flowmeters are mounted on the system. The HDS has to control the 4.5 K supercritical helium (600 g/s) for 30 superconducting coils and their superconducting bus-lines, 55 K helium (270 g/s) pressurized to 18 bars for the thermal shields and the gravity supports, and a maximum 17.5 g/s of liquid helium for 18 current leads, provided from the HRS which has a 4.5 K equivalent cooling power of 9kW. The helium distribution system consists of a helium distribution box (DB), 5 helium transfer lines, a PLC based helium control system (HCS), etc. The helium control system is connected to the KSTAR supervisory control & interlock system. The detailed status regarding the construction, commissioning during first cool-down, and the instrumentation & control (I&C) system are included in this paper. [ABSTRACT FROM AUTHOR]

The magnet system comprises sixteen toroidal field (TF) coils and fourteen poloidal field (PF) coils for KSTAR (Korea Superconducting Tokamak Advanced Research) Tokamak. All the TF coils and 10 PF coils (PF1~ 5 UL) are made of Nb3 Sn strands and 4 PF coils (PF6 ~ 7 UL) are made of NbTi strands. Before operating the superconducting coils, it is critical to verify the operation conditions such as thermo-hydraulic parameters and stability boundaries. In this regards, the TF model coil and CSMC (Central Solenoid Model Coil) have been tested and the operating conditions have been analyzed. Before cool down, parameters such as helium flow through conduits, electrical insulation and coil geometry have been measured at room temperature to confirm the manufacturing soundness. During cool down and current charging, thermo-hydraulic and mechanical parameters by using mechanical sensors have been measured. Also measured was the magnetic field strength in various positions of the coil conductor. Measured data have been analyzed and the results have been compared with the model analysis by simulation code. [ABSTRACT FROM AUTHOR]

The KSTAR (Korea Superconducting Tokamak Advanced Research) superconducting magnet system which consists of 16 TF coils and 14 PF coils adopts a superconducting CICC (Cable-In-Conduit Conductor) type conductor. The KSTAR magnet system uses two different types of CICCs--Nb3Sn cable with Incoloy 908 conduit and NbTi cable with 316LN stainless-steel conduit A continuous CICC jacketing system is developed for the KSTAR CICC fabrication and the jacketing system uses the tube-mill process. It consists of forming, welding, sizing and squaring procedures. The welding condition of CICCs and the fabrication process is described. The repair of the CICC is also discussed. [ABSTRACT FROM AUTHOR]

The KSTAR superconducting magnet system consist,s of 16 TF (Toroidal Field) and 14 PF (Poloidal Field) coils. Both of the TF and PF coil systems use internally-cooled Cable-In-Conduit Conductors (CICC). The PF coil system, which consists of 8 coils in the CS (Central Solenoid) coil system and 6 outer PF coils, provides 17 V-s and sustains the plasma current of 2 MA for 20 seconds inductively. PF 1-5 coils use Nb3Sn CICC in an Incoloy 908 conduit and PF 6-7 coils use NbTi CICC in a modified stainless steel 316LN(316LN+). The fabrication of PF7L/U & PF6L/U coils is completed at present. The engineering issues and fabrication process, which are related with the KSTAR PF 6-7 coil development, are presented and discussed in this paper. TF and PF coils are in the fabrication stage for KSTAR completion in the year 2006. [ABSTRACT FROM AUTHOR]