Search

The KSTAR superconducting magnetic coils, which are made of cable in-conduit conductor (CICC), maintain a superconducting state with forced-flow supercritical helium (4.5 K, 5.5 bar). During current changing of the superconducting magnetic coils, AC losses are generated in the CICC due to dI/dt, and the heat generated from the loss is removed by high heat capacity supercritical helium. At the same time, reversed flow of the helium occurs due to a rapid increase of the helium temperature and momentary changing of the pressure inside the CICC. This phenomenon has been detected in all of the poloidal field (PF) coils, especially in the upper (U) and lower (L) PF1 ~ PF4 coils. The maximum change of the magnetic field in the PF1UL ~ PF4UL coils is located near the inlet and outlet of the helium cooling channels, and that of the PF5UL ~ 7UL coils is located at the center of the cooling channel. The temperature variation at the helium inlet was always measured to have a time delay after each shot. In the PF1 coil tests, it was measured to have a delay of 26 sec. During the first plasma campaign, this phenomenon was more severe in the case of all PF coils operating together than for a single PF operation. In this paper, we investigated the thermal-hydraulics of this phenomenon. [ABSTRACT FROM AUTHOR]

To protect the KSTAR (Korea Superconducting Tokamak Advanced Research) superconducting coils against a quench, the quench detection system based on voltage measurement was fabricated. It used a detect/dump scheme which detects the presence of non-recovering normal zones and activates a dump circuit that transfers most of the stored energy into a dump resistor. Even though it is desirable to discharge the coil energy as fast as possible after quench detection, a time delay between the quench detection and the complete dump circuit actuation will be necessary in order that the quench voltage is to be distinguished from various noises. The quench threshold voltage and the delay time should be set before operation for quench voltage detection so that the maximum hot-spot temperature could be limited to 150 K. This paper describes the hardware techniques to prevent the malfunction of the quench detection due to voltage noises arising from the KSTAR operating scenarios. During the first operation of the KSTAR machine, the inductive voltages and other voltage noises were measured and effectively compensated below voltage thresholds. A quench did not occur and the quench detection system was well operated without any false activation. [ABSTRACT FROM AUTHOR]

To achieve the first plasma of the Korea superconducting tokamak advanced research (KSTAR), the KSTAR superconducting coils were tested in advance. As they should operate in excessively low temperature of 4.5 K and high magnetic field environment of 7.5 T, it is crucial to monitor the cryogenic and the structural behaviors of KSTAR device during the commissioning period including a cool-down. The temperatures of the KSTAR toroidal field (TF) coil and the poloidal field (PF) coils were measured during the entire operating period. The mechanical stresses on the TF and PF structures were continuously monitored to check if they go beyond the limiting value calculated through the simulation. The alignment of the KSTAR device was checked by using displacement sensors. The TF coils were successfully supplied with 15 kA DC current for 8 hours, and the maximum 5 kA/s current variation of the PF coils were tested. For the main experiment, the interlock test of the quench detection system for the KSTAR coils was carried out at reduced currents of 1 kA. From these results the quench protection circuit, and the current-flow of the KSTAR superconducting coils proved to be well performed for the first plasma operation. [ABSTRACT FROM AUTHOR]

The Korea Superconducting Tokamak Advanced Research (KSTAR) Central Solenoid Model Coil (CSMC) was tested at the National Fusion Research Center (NFRC) to verify the design and manufacturing engineering and to ensure reliable operation. The CSMC reached 8.6 T at 20 kA DC operation successfully. We also assessed the AC loss of the CSMC by means of both a sinusoidal wave with a DC offset as well as a triangular pulse. We derived a friction factor correlation of CSMC at room temperature and at cryogenic temperature (4 ∼ 6 K). We also investigated the variation of the friction factor during current charging. The KSTAR PF coil simulation code was validated with inlet and outlet helium temperature, mass flow rate, and pressure drop from the experimental results. The operation temperature margin of the CS1 coil of KSTAR was calculated with the revised KSTAR PF coil simulation coil. [ABSTRACT FROM AUTHOR]

The KSTAR Central Solenoid Model Coils (CSMC), which are in the form of split coils with same dimension, have been tested. The CSMC were successfully charged up to 20 kA and down to zero with different ramp rates. Various pulse waveforms were applied to the CSMC to analyse the AC-loss characteristics of the coils. The measurement method was a gas-flow calorimetry. In this work, two types of waveforms, the DC-biased sinusoidal wave (Idc = 2, 4 kA; ΔIac = 1 kA; ƒ = 0.08 ∼ 0.67 Hz) and a single triangular pulse (Imax = 6 ∼ 10 kA; dI/dt = 0.5 ∼ 2 kA/s), are selected and analysed. From the measured data at the one outlet where helium channel 3 and 4 are merged, the AC loss parameters, related with the hysteresis loss and the coupling loss, are calculated. The B-field strength differs depending on the position within the cooling channels. The spatial field variation and the ramp rate were 0.048∼ 1.9T and 8.1∼ 71 mT/s for the DC-biased sinusoidal waves, while 0.29∼ 4.3 T and 0.024∼ 0.86 T/s for the triangular pulses. The measured AC losses are compared with estimated values and the behavior agrees well. The coupling time constant (nτ) varies with the field strength. In case of the triangular pulses, nτ increases by increasing the field amplitude and the maximum value of nτ is 41 ms with Imax = 10 kA. [ABSTRACT FROM AUTHOR]

The KSTAR (Korea Superconducting Tokamak Advanced Research) superconducting magnet system which consists of 16 TF coils and 14 PF coils adopts a superconducting CICC (Cable-In-Conduit Conductor) type conductor. The KSTAR magnet system uses two different types of CICCs--Nb3Sn cable with Incoloy 908 conduit and NbTi cable with 316LN stainless-steel conduit A continuous CICC jacketing system is developed for the KSTAR CICC fabrication and the jacketing system uses the tube-mill process. It consists of forming, welding, sizing and squaring procedures. The welding condition of CICCs and the fabrication process is described. The repair of the CICC is also discussed. [ABSTRACT FROM AUTHOR]

The KSTAR superconducting magnet system consist,s of 16 TF (Toroidal Field) and 14 PF (Poloidal Field) coils. Both of the TF and PF coil systems use internally-cooled Cable-In-Conduit Conductors (CICC). The PF coil system, which consists of 8 coils in the CS (Central Solenoid) coil system and 6 outer PF coils, provides 17 V-s and sustains the plasma current of 2 MA for 20 seconds inductively. PF 1-5 coils use Nb3Sn CICC in an Incoloy 908 conduit and PF 6-7 coils use NbTi CICC in a modified stainless steel 316LN(316LN+). The fabrication of PF7L/U & PF6L/U coils is completed at present. The engineering issues and fabrication process, which are related with the KSTAR PF 6-7 coil development, are presented and discussed in this paper. TF and PF coils are in the fabrication stage for KSTAR completion in the year 2006. [ABSTRACT FROM AUTHOR]

The Korea Superconducting Tokamak Advanced Research (KSTAR) device requires R&D of 20-30 kA overloaded current leads (OCL) for the superconducting poloidal field (PF) magnet. The PF magnet is under zero current state for a very long time, as it is often the case for superconducting magnets used in nuclear fusion. In such case, a simple approach to reduce the cryogenic load would be to design the current leads to be overloaded. Two main problems in this R&D area are the reduction of the cryogenic heat load and the temperature rise due to the current overloading. In this paper, the current overloading tests and results of the numerical analysis for brass leads are presented and discussed in detail. [ABSTRACT FROM AUTHOR]