Search

As a flexible grinding method with high efficiency, abrasive belt grinding has been widely used in the machining of mechanical parts. However, abrasive belt grinding has not been well applied in the field of ultra-precision optical processing, due to the lack of a stable and controllable removal function. In this paper, based on the idea of deterministic machining, the time-controlled grinding (TCG) method based on the abrasive belt as a machining tool was applied to the deterministic machining of optical components. Firstly, based on the Preston equation, a theoretical model of the TCG removal function was established. Secondly, removal function experiments were carried out to verify the validity and robustness of the theoretical removal model. Further, theoretical and actual shaping experiments were carried out on 200 mm × 200 mm flat glass-ceramic. The results show that the surface shape error converged from 6.497 μm PV and 1.318 μm RMS to 5.397 μm PV and 1.115 μm RMS. The theoretical and experimental results are consistent. In addition, the surface roughness improved from 271 to 143 nm Ra. The results validate the concept that the removal function model established in this paper can guide the actual shaping experiments of TCG, which is expected to be applied to the deterministic machining of large-diameter optical components. [ABSTRACT FROM AUTHOR]

The surface quality and subsurface damage (SSD) distribution achieved with a fine-grained grinding wheel under different depth-of-cut and cutting speed is experimentally studied. The ground surface roughness (SR) is investigated via white light interferometry and expressed in terms of four typical roughness values (PV, RMS, Rz, and Ra). The SSD is characterized by the magnetorheological finishing (MRF) spot method and transmission electron microscopy. The results show that brittle-ductile surfaces and ductile-like surfaces are generated during ultra-precision grinding. Largely due to plastic flow removal, fracture defects such as fractured pits and grinding streaks on the ground surface can be mitigated. Instead, a ductile-like surface covered with grinding streaks is found. When the depth-of-cut decreases from 4 to 1 μm, the SR and SSD depth decreases from PV 1.34 μm, Ra 15.23 nm, Rz 0.94 μm, RMS 22.24 nm, and SSD 6.1 μm to PV 0.51 μm, Ra 5.07 nm, Rz 0.24 μm, RMS 6.70 nm, and SSD 1.2 μm. In addition, when the cutting speed increases from 3.9 to 23.4 m/s, the SR and SSD depth decreases from PV 1.03 μm, Ra 15.01 nm, Rz 0.82 μm, RMS 21.43 nm, and SSD 5.6 μm to PV 0.12 μm, Ra 3.17 nm, Rz 0.07 μm, RMS 4.65 nm, and SSD 0.003 μm. Moreover, the material removal mechanism under different grinding parameters is revealed by calculating undeformed chip thickness, and the mechanism of surface morphology and subsurface crack produced in brittle-ductile mode is analyzed. A linear relationship between the SR and SSD depth is in accord with the formula SSD = 0.41Ra−0.68 for brittle-ductile surfaces. [ABSTRACT FROM AUTHOR]

Unlike traditional machinery manufacturing generally using simple features of workpiece as the alignment reference, optical manufacturing, which prioritizes shape tolerances of the machining surface over position tolerances between workpiece geometry features, chooses the machining surface itself as the alignment reference. Thus, the manual alignment of workpiece in optical manufacturing could be very time-consuming when the machining surface is aspheric. Workpiece localization technology is able to automate the workpiece alignment and improve its efficiency. However, there are no relevant reports about application of this technology in the field of optical manufacturing. In this work, the workpiece localization problem for aspheric surface in magnetorheological finishing (MRF) is investigated from aspects of measurement and algorithm. The probe radius error is compensated by applying the polynomial fitting method. A new localization algorithm is proposed in order to improve the computational efficiency for the localization of aspheric surface. Simulation and experiment results verify the validity of the proposed methods. The accurate and efficient workpiece localization in MRF has been achieved and applied in real application which proves its practicability. [ABSTRACT FROM AUTHOR]

When fabricating optical cantilever parts with single-point diamond turning (SPDT) technique, chatter phenomenon happens and degenerates the surface quality. This paper studies the chatter phenomenon and proposes a scheme to solve the problem. A kind of viscoelastic material is presented as the auxiliary supporter under the vibration location of optical cantilever parts to suppress chatter. Mirror surfaces can be generated and surface shape can be maintained after uninstalling the supporter because of the special features of viscoelastic material which acts like solid to enhance the rigidity of the cantilevers when cutting forces act on it and acts like liquid to avoid distortion of the surface shape during setting and unsetting the supporter. The effect of the viscoelastic material is discussed by virtue of finite element simulation on the basis of elasticity theory. Cutting experiments are carried out and the cutting forces as well as the surface quality with and without viscoelastic supporter are compared. The results show that chatter is suppressed effectively by using viscoelastic supporter, and surface roughness average (Ra) of around 5 nm is obtained on the whole surface with no obvious distortion on machined surface shape. [ABSTRACT FROM AUTHOR]

Abstract: Single point diamond face flycutting technique is widely applied to fabricate potassium dihydrogen phosphate (KDP) crystals because of their characteristics of softness, brittleness, deliquescence and anisotropy. This paper studies the feasibility of machining KDP crystals through spiral turning method based on the ductile cutting mechanism of brittle materials. The spiral scratch method is employed to analyze various conditions of achieving brittle–ductile transition in different cutting directions where the critical depth of cut is obtained. The cutting forces and surface formation processes within different cutting parameters are discussed and the parameters ensuring full-aperture ductile turning are acquired. White light interferometer and Atomic Force Microscope (AFM) are used to evaluate the coherence of machined surface qualities in different cutting directions. The results indicate that the critical depth of cut varies from cutting directions significantly and fluctuates from about 200nm to 1000nm under the experimental condition. Cutting forces display periodical variation with the change of cutting direction and the periodical trend blurs, even ultimately disappears, with the decrease of the cutting parameters. Root-Mean-Square (RMS) value of the fabricated surface roughness fluctuates from 1.3nm to 1.7nm on the whole surface with no distinct anisotropic distribution of the surface morphology according to the results observed by AFM. Compared with face flycutting method, spiral turning method has capability to generate complex surface profiles such as aspheric or freeform surfaces and can also be used to compensate the deformation error of KDP crystals caused by vacuum suction during fabrication. [Copyright &y& Elsevier]

Optical components with complex surfaces are more and more widely applied, but it is very difficult to manufacture these components by using traditional mechanical fabricating methods. Fast tool servo system can manufacture these complex surfaces or microstructures efficiently and accurately. The relative position between the tool and workpiece surface will vary continuously in the fast tool servo machining process, owing to the height change of workpiece profile in the same circle, and this will worsen the cutting conditions and debase the machining accuracy. In this paper, the cutting characteristics are studied in the fast tool servo machining process of complex workpiece, including the varying rule of cutting angle, and its influences on the rake angle and back angle, and the choice of machining parameters. Furthermore, the conditions for identifying tool interference are given. On the basis of the above work, two kinds of typical complex workpieces are manufactured by using fast tool servo system, including radial sinusoidal workpieces and lens array. The measuring results indicate that surface accuracy can reach 0.14 μm (peak-to-valley value) and the roughness is less than 10 nm (mean value). [ABSTRACT FROM AUTHOR]

In order to investigate the influence of material anisotropy in ductile cutting of Potassium Dihydrogen Phosphate (KDP) crystals, experiments of face cutting of (001) plane of KDP crystals are carried out by using an ultra-precision lathe with a single point diamond tool. The cutting forces, surface finish, and surface roughness in all crystallographic orientations of the machined surface are measured, and a power spectrum analysis method is used to reveal the cutting force patterns. The experimental results show that the cutting forces and surface roughness vary greatly with different crystallographic orientations of KDP crystal, and that amplitude variation of cutting forces and surface finish is closely related with the cutting parameter of the maximum undeformed chip thickness. With the maximum undeformed chip thickness below 30 nm, the amplitude variation of cutting force and surface finish is minimized, and a super-smooth surface with consistent surface finish in all the crystallographic orientations can be achieved. The surface roughness is 2.698 nm (Ra) measured by Atomic Force Microscope (AFM). These findings provide criteria for achieving a large-scale KDP crystal with consistent super-smooth surface using ductile cutting technology. [ABSTRACT FROM AUTHOR]

Abstract: A new seed layer TiW is proposed for SmCo5 films with perpendicular magnetic anisotropy. The influence of a TiW seed layer on the microstructure and the surface morphology of Cu underlayer are studied. The grain size and surface roughness dependence of Cu underlayer on the thickness and the annealing of the TiW seed layer are also investigated. The improvement in the perpendicular magnetic properties of SmCo5 film from the TiW seed layer is approved. The results show that a 5nm Ti3W7 seed layer improves the microstructure and surface morphology of Cu underlayer, and significantly improves the perpendicular magnetic properties of SmCo5 film. The diffusion barrier and a high melting point of the TiW seed layer are regarded as the physical mechanism of the improvement for SmCo5 film with perpendicular magnetic anisotropy. [Copyright &y& Elsevier]