Search

Titanium and its alloys are widely employed in commercial dental devices. Because the surface morphology and chemical composition of Ti-based dental implants play a relevant role in osseointegration, three different commercial threaded implants have been investigated by scanning electron microscopy and X-ray photoelectron spectroscopy (XPS). The Implants A and C were made of pure Ti whereas the Implant B was made of Ti6Al4V alloy. Obtained results evidenced the common features and differences due to specific process parameters used in the treatments of mordanting and sandblasting for surface roughening. Implant A exhibits a uniform surface covered by very small dimples of about 1–2 μm. The surface of Implant B is not homogeneous: The thread tops present an irregular morphology (dimples size >10 μm) while finer dimples (about 1 μm) are observed along the thread flanks and valleys. Implant C shows an irregular morphology with dimples of different sizes and shapes distributed on thread tops, flanks, and valleys. XPS analyses revealed the presence of metal oxides: TiO2 in all the implants; Al2O3 and V2O5 only in the implant B. Moreover, these results demonstrated that Mg2SiO4 is present on the surface of Implant A, probably due to a specific preparation process. Obtained results have been discussed on the basis of the factors promoting the osseointegration.

Thin films of barium fluorides with different thicknesses were deposited on GaAs substrate by electron beam evaporation. The aim of the work was to identify the best growth conditions for the production of coatings with a low work function suitable for the anode of hybrid thermionic-photovoltaic (TIPV) devices. The chemical composition and work function ? of the films with different thicknesses were investigated by X-ray photoelectron spectroscopy (XPS) and ultraviolet photoelectron spectroscopy (UPS). The lowest value of ? = 2.1 eV was obtained for the film with a thickness of ~2 nm. In the valence band spectra of the films at low kinetic energy, near the cutoff, a characteristic peak of negative electron affinity was present. This effect contributed to a further reduction of the film's work function.

The outstanding mechanical strength of as-deposited DC-electrodeposited nanocrystalline (nc) Ni-Fe alloys has been the subject of numerous researches in view of their scientific and practical interest. However, recent studies have reported a dramatic drop in ductility upon annealing above 350 degrees C, associated with a concomitant abnormal rapid grain growth. The inherent cause has been ascribed to the presence of a detrimental product or by product in the bath, which affects either the microstructure or causes defects in the concentration and/or distribution of the as-deposited films. The present work has been inspired by the observed abnormal behaviour of annealed electrodeposited nc Ni-Fe alloy, which has here been addressed by considering the relationship between the composition of the bath (iron-chloride, nickel-sulphate solution, saccharin and ascorbic acid) and deposition defects (e.g. grain boundary pores) in the case of an nc Ni-Fe (Fe 48 wt%) alloy. The current investigations have included X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM) in both as-deposited and post-annealed conditions (300 degrees C-400 degrees C). XPS depth profiling with Ar ion sputtering showed a significant amount of C and O impurities entrapped in the foils during deposition. As such impurities are often overlooked in common analytical techniques, new scenarios may need to be rationalised to explain the observed drop in tensile ductility of the as-deposited Ni-Fe alloys.

The main purpose of the present work is to analyze a series of Ag nanoparticles (NPs) with different size or ligand functionalization by using X-ray photoelectron spectroscopy (XPS) and to identify the differences in the band-shape and energy peak position of photoemission spectra due to the particle dimension. A transmission electron microscopy characterization was performed, to verify the consistency of the results. Three types of samples were prepared starting from AgNO3 water solution and adding different capping agents. In the first two cases, the formation of NPs was promoted by the reduction of silver ions Ag+1 to metallic Ag-0 through the addition of sodium borohydride, whereas in the last case, it was triggered by the exposure to UV light. Depending on the size of the NPs, a different physical behavior can be recognized. NPs with diameter of about 5 nm are characterized by the phenomenon of localized surface plasmon resonance (LSPR). The other type of samples having a diameter of about 1.5 nm presents discrete energy levels instead of electronic bands, and in this case, a typical fluorescence phenomenon can be observed. In the latter case, we can refer to such systems as nanoclusters. The XPS analyses were focused on the Ag 3D spectra looking for the possible shifts of the Ag doublet as a function of the particles size. The ultraviolet photoelectron spectroscopy with He II source was used for the investigation of possible changes in the valence band.

Silver@Hydroxyapatite functionalized calcium carbonate composites have been prepared through different sustainable methods, without involving the use of organic solvents and additional reagents. The composites were characterized by X-ray powder diffraction, field emission scanning electron microscopy, transmission electron microscopy, spectrophotometric measurements and X-ray photoemission spectroscopy. From the characterization techniques, the obtained nanoparticles resulted constituted essentially by Ag3PO4 nanostructures, whose size varied from 70 to 100 nm and were uniformly distributed on the calcium carbonate surface. Upon VIS irradiation, the formation of plasmonic nanostructures with a more defined dimensional distribution and reduced size could be obtained, as a prove of a partial silver reduction. All composites exhibited good antimicrobial and antibiofilm activities against Staphylococcus aureus and Pseudomonas aeruginosa whereas they showed low cytotoxicity effects towards human skin keratinocytes and human fibroblasts. These results enable these composites to be promising candidates for biomedical and pharmaceutical applications.

The fracture surfaces of a 10.5 wt.% Cr martensitic stainless steel broken in Charpy tests have been investigated through X-ray photoelectron spectroscopy (XPS). The specimens have been examined in two different conditions: as-quenched and heat treated for 10 h at 700 &deg, C. The trends of Fe/Cr ratio vs. test temperature are similar to the sigmoidal curves of absorbed energy and, after both ductile and quasi-cleavage brittle fractures, such ratio is always significantly lower than the nominal value of the steel chemical composition. Cr segregation does not occur on a macroscopic scale but takes place in microscopic zones which represent weaker spots in the steel matrix and a preferred path for moving cracks. Small area (diameter 300 &micro, m) XPS measurements evidenced a higher density of such microscopic zones in the inner part of probes, this is explained by the different diffusion length of Cr atoms in the external and inner parts during quenching from austenitic field which has been calculated through FEM simulations. No significant differences of Cr concentration were observed in fracture surfaces of probes with and without heat treatment. The results highlight how Cr segregation plays a role not only in the intergranular mode of fracture but also in the quasi-cleavage and ductile ones.

We investigated the adsorption of heavy metal ions on a nanostructured coating of zinc-aluminum layered double hydroxides (Zn-Al LDHs) grown on aluminum foam by one-step hydrothermal process. This approach aimed to increase the interactive surface and provide a more practical medium for removal of toxic heavy metals from aqueous media. The foam coated with LDH was characterized by using scanning electron microscopy and X-ray diffraction. After immersion in a copper-rich water solution, X-ray photoelectron spectroscopy demonstrated the occurrence of adsorbed copper on the LDH-coated foam with two oxidation states: particles of metallic copper Cu(0)with oxidized surface Cu+1. X-ray diffraction showed the presence of Cu(+2)in the LDH structure.

Cr martensitic steels are promising materials for structural applications in future nuclear fusion reactors. Because the embrittlement after tempering treatments can be a serious problem, the fracture mode of a steel with 10.5 wt% of Cr treated at 700 degrees C for 18 h has been investigated through Charpy tests in the temperature range from -100 degrees C to +150 degrees C. X-ray photoelectron spectroscopy (XPS) analyses carried out on the fracture surfaces evidenced the segregation of Cr in both ductile and brittle (quasicleavage) fields. The unexpected result indicates that Cr segregation weakens the atomic bonds; thus, the fracture path in both the cases corresponds to the zones with higher Cr content.

The main principles and development of electron spectroscopy for chemical analysis (ESCA) are briefly reviewed. The role of ESCA techniques (X-ray photoelectron spectroscopy and Auger electron spectroscopy) in the investigation of metallic surfaces is discussed, evidencing their importance and analytical potentiality. An overview is given of a series of recent experimental cases of ESCA application for the characterization of different metals and metallic alloys, illustrating the main results and various phenomena, such as the formation of impurity defects, corrosion, migration of constituent elements in various alloys, clustering in liquid alloy, etc., that can occur on the surface and the interface of investigated materials. These materials comprise the collection coins of noble metals, some metal alloys and Ni-based superalloys, nitride coatings on stainless steel, composite material with TiAlV alloy, treated austenitic steels, and graphene interface with polycrystalline metal foils. The present review could be particularly recommended for the newcomers to the research field of surface analysis and its application for various metals, their treatments, and possible modifications in operating conditions.