Search

Soft-switching inverters can achieve high efficiencies and low switchdv/dtanddi/dt, but often impose additional stress on the switches due to their resonant behavior. Multicell converters, on the other hand, can process high voltages by arranging the switches to share the stress. This paper proposes a buck–boost multicell soft-switching inverter with inherent cell voltage balancing. Both the current and voltage stresses are shared by the cells. Soft-switching conditions are achieved for all switching transitions without any need for auxiliary circuitry or clamps. A multiple-winding transformer transfers energy between the terminals and provides galvanic isolation. An analytical study and experimental results on a 1200-W prototype verify the operation of the inverter. [ABSTRACT FROM AUTHOR]

This paper presents a novel single-stage soft-switched high-frequency-link three-phase dc–ac converter topology. The topology supports unidirectional dc to ac power flow and is targeted for applications like grid integration of photovoltaic sources, fuel cell, etc. The high frequency magnetic isolation results in reduction of system volume, weight, and cost. Sine-wave pulsewidth modulation is implemented in dc-side converter. Though high-frequency switched, dc-side converter is soft switched for most part of the line cycle. The ac-side converter active switches are line frequency switched incurring negligible switching loss. The line frequency switching of ac-side converter facilitates use of high voltage blocking inherently slow semiconductor devices to generate high voltage ac output. In addition, a cascaded multilevel structure is presented in this paper for direct medium-voltage ac grid integration. A detailed circuit analysis considering nonidealities like transformer leakage and switch capacitances, is presented in this paper. A 6-kW three-phase laboratory prototype is built. The presented simulation and experimental results verify the operation of the proposed topologies. [ABSTRACT FROM AUTHOR]

In this paper, a class of single-phase Z-source (ZS) ac–ac converters is proposed with high-frequency transformer (HFT) isolation. The proposed HFT isolated (HFTI) ZS ac–ac converters possess all the features of their nonisolated counterparts, such as providing wide range of buck-boost output voltage with reversing or maintaining the phase angle, suppressing the in-rush and harmonic currents, and improved reliability. In addition, the proposed converters incorporate HFT for electrical isolation and safety, and therefore can save an external bulky line frequency transformer, for applications such as dynamic voltage restorers, etc. The proposed HFTI ZS converters are obtained from conventional (nonisolated) ZS ac–ac converters by adding only one extra bidirectional switch, and replacing two inductors with an HFT, thus saving one magnetic core. The switching signals for buck and boost modes are presented with safe-commutation strategy to remove the switch voltage spikes. A quasi-ZS-based HFTI ac–ac is used to discuss the operation principle and circuit analysis of the proposed class of HFTI ZS ac–ac converters. Various ZS-based HFTI proposed ac–ac converters are also presented thereafter. Moreover, a laboratory prototype of the proposed converter is constructed and experiments are conducted to produce output voltage of 110 Vrms / 60 Hz, which verify the operation of the proposed converters. [ABSTRACT FROM AUTHOR]

To transmit constant powers particularly at light load, the isolated dual active bridge (DAB) with conventional dual-phase-shift (DPS) control exhibits large variations of currents, losses, and efficiencies if there is a small change of outer phase shift ratio, which is caused by the change of command to adjust power transmission. This is mainly because of the narrow operation region of outer phase shift ratio if the conventional DPS modulation is used. To solve this problem, a novel DPS control with bidirectional inner phase shifts for the DAB is developed to reduce the current surge in the high-frequency transformer, which can stabilize the output power with high efficiency. From the analysis of operation modes and power characteristics of the proposed DPS control, it is shown that due to wider operation region of outer phase shift ratios compared with the conventional DPS control in which the inner phase shifts of both the primary and secondary H-bridges are in the same direction, lower surge current can be obtained in the change of phase shift command, which results in stable power transmission particularly at light load without scarifying the efficiency. Moreover, the DAB of using the proposed DPS control can transmit bidirectional energy with the inner and outer shift ratios of 0–1. For experimental verifications, the test results are also presented in this paper. [ABSTRACT FROM AUTHOR]

With the background of power supplies for high-precision apparatuses, an isolated high-frequency dc–ac converter based on a differential output structure is proposed. It is composed of two phase-shifted full bridges (PSFBs) that share a common half-bridge as the lagging leg on the primary side. Two current-doubler synchronous rectifiers (CDRs) constitute the differential output structure on the secondary side. The ac output is synthesized by the two PSFB-CDRs generating the same dc bias and phase-reversed ac components. Compared with traditional solutions, the new circuit has the potential capability to obtain an ultralow distortion output voltage without using special control or compensations. Moreover, zero voltage switching is realized in the primary circuit within a wide load range, whereas zero current switching is achieved in the secondary circuit. Operation principles are analyzed, and a 1-kW prototype is built to validate the proposed scheme. [ABSTRACT FROM PUBLISHER]

The increase of transmission frequency reveals more merits than low- or medium-frequency distribution among different kinds of power applications. High-frequency inverter serves as source side in high-frequency ac (HFAC) power distribution system (PDS). However, it is complicated to obtain a high-frequency inverter with both simple circuit topology and straightforward modulation strategy. A novel switched-capacitor-based cascaded multilevel inverter is proposed in this paper, which is constructed by a switched-capacitor frontend and H-Bridge backend. Through the conversion of series and parallel connections, the switched-capacitor frontend increases the number of voltage levels. The output harmonics and the component counter can be significantly reduced by the increasing number of voltage levels. A symmetrical triangular waveform modulation is proposed with a simple analog implementation and low modulation frequency comparing with traditional multicarrier modulation. The circuit topology, symmetrical modulation, operation cycles, Fourier analysis, parameter determination, and topology enhancement are examined. An experimental prototype with a rated output frequency of 25 kHz is implemented to compare with simulation results. The experimental results agreed very well with the simulation that confirms the feasibility of proposed multilevel inverter. [ABSTRACT FROM AUTHOR]

This paper presents a single-stage bidirectional high-frequency transformer (HFT) link dc/ac converter topology for a three-phase adjustable magnitude and frequency PWM ac drive. This type of converters find a wide range of applications including UPS systems, drives involving renewable energy sources (Solar, Fuel cell), and energy storage systems (typically low voltage dc to high voltage PWM ac). The HFT results in reduction in cost and weight along with a considerable increase in power density. The adverse effects of common-mode voltage are well known in this kind of applications. The proposed topology along with a modulation technique reduces common-mode voltage to practically zero and generates high-quality output voltage waveform comparable to conventional space vector PWM (CSVPWM). A source-based commutation method, presented in this paper, to commute the energy stored in the leakage inductance of the HFT resulting in the following advantages 1) no need for any auxiliary circuits with passive components; 2) almost complete recovery of the leakage energy; 3) soft switching of the output side converter for all load conditions; and 4) minimization of common-mode voltage switching due to commutation. The converter along with the suggested control has been analyzed in detail. The presented simulation and experimental results confirm the operation of the proposed converter. [ABSTRACT FROM AUTHOR]

This letter presents a new zero-voltage-switching (ZVS) isolated dc–dc converter which combines a boost half-bridge (BHB) cell and a full-bridge (FB) cell, so that two different type of power sources, i.e., both current fed and voltage fed, can be coupled effectively by the proposed converter for various applications, such as fuel cell and supercapacitor hybrid energy system. By fully using two high- frequency transformers and a shared leg of switches, number of the power devices and associated gate driver circuits can be reduced. With phase-shift control, the converter can achieve ZVS turn-on of active switches and zero-current switching (ZCS) turn-off of diodes. In this letter, derivation, analysis, and design of the proposed converter are presented. Finally, a 25–50 V input, 300–400 V output prototype with a 600 W nominal power rating is built up and tested to demonstrate the effectiveness of the proposed converter topology. [ABSTRACT FROM AUTHOR]

This paper presents the design of new high-frequency transformer isolated bidirectional dc-dc converter modules connected in input-series-output-parallel (ISOP) for 20-kVA-solid-state transformer. The ISOP modular structure enables the use of low-voltage MOSFETs, featuring low on-state resistance and resulted conduction losses, to address medium-voltage input. A phase-shift dual-half-bridge (DHB) converter is employed to achieve high-frequency galvanic isolation, bidirectional power flow, and zero voltage switching (ZVS) of all switching devices, which leads to low switching losses even with high-frequency operation. Furthermore, an adaptive inductor is proposed as the main energy transfer element of a phase-shift DHB converter so that the circulating energy can be optimized to maintain ZVS at light load and minimize the conduction losses at heavy load as well. As a result, high efficiency over wide load range and high power density can be achieved. In addition, current stress of switching devices can be reduced. A planar transformer adopting printed-circuit-board windings arranged in an interleaved structure is designed to obtain low core and winding loss, solid isolation, and identical parameters in multiple modules. Moreover, the modular structure along with a distributed control provides plug-and-play capability and possible high-level fault tolerance. The experimental results on 1 kW DHB converter modules switching at 50 kHz are presented to validate the theoretical analysis. [ABSTRACT FROM AUTHOR]