Search

Resonant switched-capacitor converters have widely been used recently to increase conversion power density. The most significant drawback of these converters is voltage regulation problem when their input voltages vary in wide ranges. Here, a basic double voltage-ratio resonant switched-capacitor converter (SCC) is analyzed and simulated below its resonant frequency under the different operation modes to overcome this problem. The converter different parameters are calculated under both continuous conduction mode (CCM) and discontinuous conduction mode (DCM) conditions. The advantages and drawbacks of these operation modes are compared and the closed-loop control of the converter is also investigated based on the extended describing function approach. The given analyses demonstrate that the output voltage can be well-regulated under the CCM1 and DCM2 operation modes even when wide input voltage and load variations are applied. Besides, the DCM1 operation mode must be avoided when output voltage regulation is important. Based on the given analytical and experimental results, switching frequency varies in a reasonable range to regulate the output voltage. Also, faster transient responses, smaller output capacitor, and smaller resonant tank components can be used below the resonant frequency, as compared to the above resonant frequency, but lower efficiency value is achieved. The given approach has been extended to the other resonant SCCs as well. [ABSTRACT FROM PUBLISHER]

In this paper, a novel single-stage three-port inverter that connects photovoltaic (PV) panel to a single-phase power grid is introduced. In a single-phase grid-connected PV panel, the input power is constant during the line-frequency period, while the output power oscillates at double-line frequency. A series active power decoupling circuit utilizing thin-film capacitors is incorporated to a conventional flyback inverter to handle input and output power differences. Therefore, popularly low-reliable electrolytic capacitors are replaced with small long-lifetime thin film. The proposed inverter can extract the maximum power from PV, deliver a low total harmonic distortion sinusoidal current to the output, and decouple the input and output powers. The proposed power decoupling circuit shares the inverter main switch. Thus, these functions are achieved using just three switches and a simple control scheme which is applicable for both charging and discharging states. Operation principle and control strategy are discussed in detail. Experimental results based on a 100-W prototype inverter verify feasibility and functionality of the proposed inverter. [ABSTRACT FROM PUBLISHER]

Multiterminal converters eliminate using several single-input-single-output converters and simplify their topologies and reduce their cost. In this paper, a new family of multi-input converters based on three switches leg is introduced. Inputs of the proposed converters are similar and they are topologically interchangeable and have boost or buck operation modes. The proposed converter has one output that operates as an inverter. Here, all operating modes of the proposed converters and their effects on each other are investigated, in details. Also, an appropriate switching technique for the converters is given. A detailed comparison between conventional and proposed two-input converters is also presented. A two-input, one-output prototype converter has been implemented to validate the given analyses and to verify the proposed converter's performance. The experimental results are in good agreement with the theoretical and simulated analyses. [ABSTRACT FROM AUTHOR]

A resonant switched-capacitor converter (SCC) has been analyzed above its resonant frequency to realize zero-voltage switching (ZVS) and to overcome voltage regulation issue of SCCs even when wide input voltage and output power variations are applied. ZVS operation under the continuous conduction mode (CCM) conditions improves efficiency due to lower conduction and switching losses. It is more efficient than the widely used zero-current switching (ZCS) approach in recent years under the discontinuous conduction mode (DCM) condition. Because, switching losses dominant components are reduced in MOSFET-based converters under the ZVS not ZCS conditions. Also, it has been demonstrated that output voltage can be well regulated under the CCM operation when wide input voltage and load variations are used. When output voltage regulation is not the major issue, operating at fixed switching frequency higher than, but near to, the resonant frequency results smaller components, higher power density, and lower electromagnetic interference level, as compared to the constant voltage ratio DCM operation mode, widely used in recent years. Also, output voltage ripple has been calculated, in details, by considering parasitic components of the output capacitor. A 110–165 to 200 V SCC has been implemented in 206.6–402.5 kHz frequency range to deliver 100–500 W. Maximum and average efficiency values equal to 96.8% and 94% are achieved, respectively. [ABSTRACT FROM PUBLISHER]