Search

The multiactive-bridge (MAB) structure has obvious efficiency and cost advantages in multiport power electric transformer, but it brings the characteristics of strong current coupling of each transformer. To improve the dynamic response speed of MAB and reduce the coupling characteristics, a high-frequency current predictive control (CPC) method for MAB is proposed in this letter. The controller uses the enhanced single-phase shift modulation method to adjust the phase shift angle and duty cycle of four ports at the same time so that the high-frequency current can be adjusted in several switching cycles. In the proposed CPC method, the influence of control delay is analyzed and compensated, and the dc offset, which may occur in the dynamic process is analyzed and gives corresponding solutions. More importantly, the proposed CPC method can be extended to the power predictive control method to realize power decoupling of multiple ports of MAB. The parameter robustness of current and power predictive control is analyzed briefly in this letter. The proposed control method is validated on a hardware-in-loop simulation platform based on RT-lab. Experiment results show the superior dynamic performance and good robustness of the proposed method. [ABSTRACT FROM AUTHOR]

The noninverting buck–boost (NIBB) converter is a step-up and step-down dc–dc converter suitable for applications with a wide input voltage range. However, this circuit will face the problem of operating mode switching when the input voltage is close to the output voltage. Considering this problem, the principles of the NIBB converter are analyzed in this article. The duty cycle combinations of an NIBB converter are analyzed, and an analysis method for the mode transition problem from a geometric perspective is proposed. Using the two-edge pulsewidth modulation method, a novel bumpless mode transition control method is proposed. A nonlinear feedforward controller with hysteresis is designed according to the state equation of the circuit. Moreover, the inductor current reference value is compensated when the mode is switched so that the mode transition problem of the NIBB circuit is effectively solved. In addition, a small-signal analysis of the proposed method is performed. The analysis shows that the proposed method has good stability and dynamic performance in various typical conditions. A 10-kW NIBB prototype is built in this article, and the corresponding experimental scenarios are designed. The experimental results show that compared with the results of unified PI control during the mode transition, the transient oscillation of the output voltage is smaller, and the duration of the transient process is shorter. [ABSTRACT FROM AUTHOR]

Multileg Class-D amplifiers (CDAs) with phase-shifted carrier modulation can increase the equivalent switching frequency and reduce the output current ripples, which further reduces the size of the output filter. However, these benefits are degraded by the tolerances in the phase inductance values. The phase inductance mismatches impact the ripple cancelation effects (the harmonic contents at switching frequency and its harmonics appearing in the output current ripple). Therefore, the quality of the output waveform can further be impacted. Current research works dealing with this issue mainly focused on the interleaved dc–dc converters, which does not cover the analysis in multileg CDAs or inverters, especially for the full-bridge configuration. This paper proposes a general analytical method to characterize the steady-state phase and the total current ripple in the multileg CDAs with full-bridge configuration under inductance mismatches. Monte Carlo simulation is used to study the impact of inductance mismatches on the harmonic contents of the total current ripple, and the distribution law of the inductances at the worst case is revealed. The analytical method is verified by simulation and experimental results of a four-leg full-bridge CDA. A design guideline is given to optimize the filter design based on the analytical method. [ABSTRACT FROM AUTHOR]

The nonlinear junction capacitances of power devices are critical for the switching transient, which should be fully considered in the modeling and transient analysis, especially for high-frequency applications. The silicon carbide (SiC) MOSFET combined with SiC Schottky Barrier Diode (SBD) is recognized as the proposed choice for high-power and high-frequency converters. However, in the existing SiC MOSFET models only the nonlinearity of gate-drain capacitance is considered meticulously, but the drain–source capacitance, which affects the switching commutation process significantly, is generally regarded as constant. In addition, the nonlinearity of diode junction capacitance is neglected in some simplified analysis. Experiments show that without full consideration of nonlinear junction capacitances, some significant deviations between simulated and measured results will emerge in the switching waveforms. In this paper, the nonlinear characteristics of drain–source capacitance in SiC MOSFET are studied in detail, and the simplified modeling methods for engineering applications are presented. On this basis, the SiC MOSFET model is improved and the simulation results with improved model correspond with the measured results much better than before, which verify the analysis and modeling. [ABSTRACT FROM AUTHOR]