Search

Pulsewidth modulation (PWM) strategies, including continuous PWM (CPWM) and discontinuous PWM (DPWM), have been efficiently applied in the three-phase voltage source converters (VSCs). In the three-phase VSCs, dead-time distortion is inevitable. The characteristics of the dead-time distortion of three-phase VSCs with CPWM strategies have been studied extensively, whereas those of DPWM strategies have not been studied in detail. In this article, a comparative analysis of the dead-time distortion of CPWM strategies and DPWM strategies is conducted. Furthermore, the improvement of the PWM strategies to mitigate dead-time distortion is presented. The improved PWM strategies inject the compensation signals to the modulation signals to reconstruct the dead-time voltage error, which can significantly reduce the dead-time distortion of various PWM strategies. Experimental tests are conducted and the experimental results are provided to verify the analysis results of the dead-time distortion of DPWM strategies and the improved PWM strategies. [ABSTRACT FROM AUTHOR]

Due to the input current dead zones, the buck power factor correction converter has to set a fixed output voltage for a tradeoff between the total harmonic distortion (THD ${_\mathit{i}}$) and efficiency. Thus, many converter-cell integrated buck-type converters have been proposed to eliminate the dead zones, which unfortunately deteriorate efficiency due to the extra components.This article proposes a group of bridgeless buck-type integrated topologies. Then, a dead-zone-free bridgeless buck-type topology with a wide output voltage range is targeted for further study. The studied converter operates in the buck+flyback mode and can automatically change to flyback mode when the dead zones occur, which only requires a simple control. Moreover, an integrated transformer based on an E-E core is investigated to reduce cost and volume. The bridgeless operation modes are introduced, followed by the PF and THD ${_\mathit{i}}$ analysis to optimize its performance. Prototypes are built and tested, which confirm the effectiveness of the converter and the integrated magnetic. [ABSTRACT FROM AUTHOR]

Given the telecom base transceiver station (BTS) load mission profiles, a mixed conduction mode (MCM) control for a bridgeless boost PFC converter (IPOS boost) is proposed to mainly improve its power factor and reduce the input current total harmonic distortion (THD ${_{\mathit{i}}}$) in the light-load conditions. The principle of the MCM control and the efficiency analysis are introduced. Then, the experimental verification is performed to show the control effectiveness and performance improvements. Furthermore, a mission profile-based reliability assessment for the PFC converter is presented to analyze the IPOS boost under the classical average current (AVC) control and the proposed MCM control, along with its conventional boost counterpart under the AVC control. Considering the measured efficiency data and BTS typical mission profiles in a rural area, the analysis results indicate that given 20 years of operation, the accumulated failure of the IPOS boost under the AVC controls is 0.27%, and is further decreased to 0.24% by just the software update with the proposed MCM control. By contrast, the accumulated failure of the conventional boost counterpart under the AVC control is 2.06%, much higher than the IPOS boost. [ABSTRACT FROM AUTHOR]

This article introduces two general ways to derive single-phase bridgeless power factor correction (PFC) topologies and then, 15 accessible bridgeless topologies are derived based on the configuration of different basic types of dc–dc converter cells. Although the majority of the topologies have been previously proposed, other possible research points are reviewed. Besides, a consistent component sizing procedure with electric, thermal, and cost models is applied to conduct the performance benchmarking of these PFC topologies in terms of power loss, volume, and cost. Three boost-type PFC topologies are chosen as examples to demonstrate the procedure and the corresponding benchmarking results with both theoretical analyses and experimental verification. Finally, mission profiles of one specific application are introduced to show the material cost payback period of adopting one modified bridgeless boost topology instead of conventional one in different scenarios. [ABSTRACT FROM AUTHOR]

Compared with constant duty cycle-controlled discontinuous conduction mode (DCM) boost power factor (PF) correction (PFC) converter, constant duty cycle-controlled quadratic DCM–DCM boost PFC converter features with much lower second-order line frequency output voltage ripple, and however, it suffers from low PF. To increase PF of quadratic DCM–DCM boost PFC converter, a variable duty cycle control technique for quadratic DCM–DCM boost PFC converter is presented in this paper. An approximation equivalent for the variable duty cycle is employed to simplify the implementation circuit. The corresponding expressions of PF and output voltage ripple are analyzed. For input voltage range of 100–240 Vac, quadratic DCM–DCM boost PFC converter with variable duty cycle control benefits with very high PF, and tradeoff between PF and output voltage ripple of this converter is analyzed. Experimental results from 100-W prototypes are given to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]