Search

The article presents a novel carrier-based pulsewidth modulation technique for multiphase neutral point clamped converters. The technique is aimed to actively control the neutral point (NP) potential while supplying the desired set of line-to-line voltages to the load. Standard techniques are either based on the sole common mode voltage injection or on the sole multistep switching mode; contrarily, the proposed algorithm combines these two approaches to take advantage of their main benefits. The technique performs well for each number of phases, for each modulation index, and for each type of load. It can control in closed-loop the NP voltage to any desirable value with a reduced number of switching transitions. The proposed approach has been experimentally validated and compared with other carrier-based algorithms. [ABSTRACT FROM AUTHOR]

This article presents a generalized approach toward the dc-link voltage switching ripple analysis in the two-level multiphase pulsewidth modulation (PWM) voltage source inverters with a balanced load. Since the voltage ripple is one of the crucial sizing criteria for a dc-link capacitor, a simple and practical equation for designing the dc-link capacitor, based on the maximum (peak-to-peak) value of the dc-link voltage ripple, has been proposed for the multiphase inverters. The amplitude of the dc-link voltage switching ripple is analytically derived as a function of operating conditions. The effect of the number of phases on the dc-link capacitor size is investigated as well. It is found that considering the same total output current, the dc-link capacitor size is reduced by increasing the number of phases up to seven. However, from the point of view of the dc-link capacitor size, there are no benefits of further increasing the number of phases. Reference is made to two commonly used modulation strategies—sinusoidal PWM and continuous symmetric centered PWM (i.e., space vector). The mathematical models are derived with an aim to provide the precise dc-link capacitor sizing and hence improve the power density of the whole system. The comparison of different phase numbers has been made. Proposed theoretical developments are verified by the simulation and experimental tests. [ABSTRACT FROM AUTHOR]

In this article, a new pulsewidth modulation technique is proposed for the output voltage control and the dc-bus capacitors voltage balancing of a multipoint-clamped multilevel converter. The voltage equalization is achieved by allowing each converter's leg voltage to switch through multiple levels in a single modulation period (multistep operation). The approach is generalized with respect to the number of levels and phases and can be applied regardless of the converter operating conditions. Nevertheless, the multistep behavior generally leads to an increase of the average switching transitions rate. In the proposed method, this drawback is mitigated with an online adaptive selection of the number of switching levels. The algorithm is validated through an extensive hardware-in-the-loop testing and compared to other approaches. [ABSTRACT FROM AUTHOR]

This paper studies pulse width modulation (PWM) techniques suitable for a four-level five-phase open-end winding (OeW) drive. The drive comprises a five-phase induction machine, supplied using two two-level voltage source inverters with isolated and unequal dc-link voltages, in the ratio 2:1. A decoupled carrier-based (CB) PWM modulation strategy, based on unequal voltage reference sharing between the two converters, is introduced in this paper. The stability of dc-link voltages in OeW drives is investigated next, using a novel analysis technique. Several modulation methods are analyzed and the results show that application of the coupled PWM technique, with carriers having in-phase disposition, leads to overcharging of the capacitor in the dc-link of the inverter intended to operate with the lower dc-link voltage. On the other hand, the proposed decoupled CB PWM scheme naturally eliminates the dc-link capacitor overcharging problem. These findings are verified experimentally, using open-loop V/f control. Two different decoupled CB modulation methods are compared and the best performing modulation method is selected and incorporated further into an OeW drive with field-oriented control. The presented steady state and transient experimental results demonstrate that the decoupled CB PWM technique is suitable for high-performance variable speed drive applications. [ABSTRACT FROM AUTHOR]

Three-phase multilevel (ML) inverters are used in many medium- and high-power applications such as motor drives and grid-connected systems. Despite the fact that numerous pulsewidth modulation (PWM) techniques for ML inverters have been developed, the impact of these modulation schemes on the peak-to-peak output current ripple amplitude has not been addressed yet. In this paper, analysis and comparison of current ripple for two-level (2L) and three-level (3L) voltage source inverters are given. Reference is made to optimal and popular modulation, so-called centered PWM, easily obtained by both carrier-based modulation (phase disposition, with proper common-mode voltage injection) and space vector modulation (nearest three vectors). It is shown that the peak-to-peak current ripple amplitude in 3L inverters can be determined on the basis of the ripple in 2L inverters, obtaining the same results as by directly analyzing the output voltage waveforms of the 3L inverters. This procedure can be readily extended to higher level numbers. The proposed analytical developments are verified by both numerical simulations and experimental tests. [ABSTRACT FROM PUBLISHER]

The analysis and assessment of the pulsewidth modulation (PWM) techniques is commonly based on the comparison of the total harmonic distortion (THD) results. THD is usually calculated by application of the Fourier transformation and by taking a limited number of harmonics into the consideration. In this paper, derivation of analytical formulas for the phase voltage THD is presented. The considered system is a symmetrical multiphase star-connected load, supplied from a multilevel pulsewidth-modulated voltage-source inverter (VSI, three-phase case is also covered). The solution is based on the Parseval's theorem, which links frequency spectrum and time domain through the average power (i.e., root-mean-square (rms) squared value) of the signal. The assumption throughout the derivations is that the ratio of the switching to fundamental frequency is high. Derivations are based on the integration of the power of the PWM signal in a single switching period over the fundamental period of the signal. Only ideal sinusoidal reference voltages are analyzed, and no injection of any type is considered. Formulas for phase voltage THD for any number of phases are derived for two- and three-level cases, for the most commonly used carrier-based methods. Comparison of the analytically obtained curves with simulation and experimental results shows a high level of agreement and validates the analysis and derivations. [ABSTRACT FROM AUTHOR]

Multilevel inverter supplied multiphase variable-speed drive systems have in recent times started attracting more attention, due to various advantages that they offer when compared to the standard three-phase two-level drives. For proper functioning of such systems good pulsewidth modulation (PWM) strategy is of crucial importance. Control complexity of multiphase multilevel inverters increases rapidly with an increase in the number of phases and the number of levels. This paper deals with a three-level neutral point clamped (NPC) inverter supplied five-phase induction motor drive and analyses five PWM strategies: three are carrier-based (CBPWM) and two are space vector based (SVPWM). The aim is to provide a detailed comparison and thus conclude on pros and cons of each solution, providing a guideline for the selection of the most appropriate PWM technique. Experimental results are provided for all analysed PWM methods. The comparison of the PWM techniques is given in terms of the voltage and current waveforms and spectra, as well as the total harmonic distortion (THD) in a whole linear modulation index range, which is used as the global figure of merit. Properties of the common mode voltage (CMV) are also investigated. Complexity of the algorithms, in terms of the computational time requirements and memory consumption, is addressed as well. It is shown that the performance of the PWM techniques is very similar and that one CBPWM and one SVPWM technique are characterised with identical performance. However, using the algorithm complexity as the main criterion, space vector techniques are more involved. [ABSTRACT FROM PUBLISHER]

This paper presents a novel modulation strategy for a seven-phase three-level inverter, aimed at variable-speed drive applications. Developed space vector pulsewidth modulation (SVPWM) strategy is based on vector space decomposition (VSD) approach and an analysis of multidimensional space vector projections in mutually orthogonal planes. The algorithm represents an extension of a recently developed five-phase three-level SVPWM algorithm and is considerably more complex, due to the existence of three mutually orthogonal planes in a seven-phase system. The difficulties of generalization of space vector strategies, which stem from the nature of the multiphase systems, are highlighted. Increasing the number of phases from five to seven increases the number of switching states from 3 ^5 = 243 to 3^7 = 2187 and the number of orthogonal planes from two to three. This considerably affects the complexity of the offline calculations. However, the final implementation of the algorithm is simple. Developed SVPWM algorithm is compared to an equivalent carrier-based strategy and it is shown that they yield identical performance. The complexity of the algorithms for real-time implementation is compared. Simulation and experimental results, obtained using neutral-point clamped inverter, verify the theoretical developments. [ABSTRACT FROM AUTHOR]