Search

This article proposes a new control method for the synchronous rectifier (SR) of phase-shifted full-bridge (PSFB) converter to improve its efficiency in light-load condition. In general, the PSFB converter operates in the discontinuous conduction mode (DCM) in light-load condition to reduce the effective duty-ratio and core loss. However, the conventional control methods in the DCM cause undesirable conduction loss in SR because the output inductor current flows through the body-diode instead of the channel of SR. To figure it out, the proposed control method modulates the turn-on time of SR to eliminate the body-diode conduction. Moreover, it can be easily implemented without any auxiliary circuits. Therefore, it can improve the efficiency in light-load condition while keeping the advantages of DCM. The operating principle of PSFB converter in the DCM is first described. Thereafter, the proposed control method for SR is theoretically analyzed. Finally, its practical effectiveness is verified by experimental tests on the hardware implementation. [ABSTRACT FROM AUTHOR]

This article proposes a novel sawtooth-carrier based pulsewidth-modulation (SCPWM) method for quasi-Z-source inverter (qZSI) with the zero-voltage-switching (ZVS) operation to reduce the total harmonic distortion (THD) and inductor current ripple. The conventional variable-duty pulsewidth-modulation (VDPWM) method has been being used for qZSIs because it causes the low switching loss. However, this method has the limitation not only to improve the THD of output current but also to reduce the size of inductor when it is applied to the qZSI. To figure it out, the proposed SCPWM method uses the sawtooth-carrier signal while keeping the benefit from the use of variable duty. In particular, the ZVS operation occurs whenever the edge of sawtooth-carrier signal is located in the time interval of shoot-through state. This allows to increase the carrier frequency of qZSI without any additional switching loss. Thus, both the THD of output current and the inductor current ripple can be reduced while keeping the high efficiency of system. The operating principle of the proposed SCPWM method is first explained in detail. Thereafter, its performance is mathematically analyzed and compared with that of conventional VDPWM method. Finally, its practical effectiveness is verified by the hardware experimental test. [ABSTRACT FROM AUTHOR]

This paper describes the development of a new buck cascaded buck–boost power factor correction (PFC) converter of 2 kW with a soft-switching technique. For its wide range of input voltage, it operates in both buck and boost modes. The parameters are properly selected to endure voltage and current stress in all operating ranges. In addition, the electromagnetic interference (EMI) filter is used to reduce the EMI noise and guarantee continuous input current in buck operation. Moreover, the zero-voltage-transient pulse-width-modulation (ZVT-PWM) method is applied to improve the overall efficiency of the converter. The performance of the proposed PFC converter with the widest range of input voltage is evaluated by the hardware experimental test including harmonics analysis based on the International Electrotechnical Commission standard in all operating ranges. Also, the variations of power factor are theoretically analyzed in both buck and boost modes to determine the widest input range of the proposed PFC converter of 2 kW with an EMI filter. These are strongly required to commercialize it in practice. Finally, the efficiency of proposed PFC converter is compared with that of a conventional buck cascaded buck–boost PFC converter under various conditions. [ABSTRACT FROM PUBLISHER]

This paper describes the Hessian matrix estimation of nonsmooth nonlinear parameters by the identifier based on a feedforward neural network (FFNN) embedded in a hybrid system, which is modeled by the differential–algebraic–impulsive–switched (DAIS) structure. After identifying full dynamics of the hybrid system, the FFNN is used to estimate second-order derivatives of an objective function \bf J with respect to the nonlinear parameters from the gradient information, which are trajectory sensitivities. Then, the estimated Hessian matrix is applied to the optimal tuning of a saturation limiter used in a practical engineering system. [ABSTRACT FROM PUBLISHER]

This paper proposes the new clamping angle control (CAC) pulse width modulation (PWM) method to restore its maximum linear modulation range of voltage source inverters (VSIs) reduced by the duty ratio limitation in hardware implementation, which makes the VSIs to operate nonlinearly in the high modulation range. The deadtime and the bootstrap gate driver circuit mainly cause this duty ratio limitation in practice. In particular, the bootstrap gate driver circuit is used in many industrial applications by avoiding the additional power supply to apply the gate-source voltage of power switches, and therefore making the VSIs to be small size with the low cost. First, the proposed CACPWM method is theoretically analyzed. Then, it is applied in the high modulation range to overcome the limitation of the duty ratio due to the use of the bootstrap gate driver circuit. Thereafter, its practical effectiveness is verified by both simulation and experimental tests. Also, the resulting harmonic distortions are compared with those by the conventional PWM methods. [ABSTRACT FROM AUTHOR]

Like conventional two-switch leg converters, the three-switch leg converters also have short-circuit risks and a dangerous shoot-through current is generated if switches of the same leg are turned on simultaneously. In this article, a new dual-buck structure is proposed for three-switch leg converters. The proposed structure is reliable because of no shoot-through concerns and high quality of output waveforms can be obtained due to the reduction in pulsewidth modulation deadtime. Unlike the conventional dual-buck three-switch leg that uses many passive components such as four current limiting inductors and three external diodes, the new dual-buck three-switch leg uses only one current limiting inductor with two external diodes. To verify the performance, the proposed three-switch legs are used in single-phase dual-output inverter and detailed theoretical analysis, simulation, and experiments are performed. Both continuous and discontinuous modulation schemes are applied and it has been figured out that discontinuous modulation scheme can improve the dc-link voltage utilization in the common-frequency mode of operation. [ABSTRACT FROM AUTHOR]

This article proposes the new noninverting buck–boost ac–ac converter, which can minimize the reverse recovery loss by disabling the body diodes of switches and using the external fast recovery diodes for its current freewheeling. In particular, the proposed ac–ac converter takes advantages of metal-oxide semiconductor field effect transistors and external fast recovery diodes to achieve the high efficiency. Also, it has the high reliability without the shoot-through and dead-time considerations in the circuit. Moreover, it can be simply implemented without employing the conventional commutation control. This results in decreasing the control complexity. As its proper application, a new type of dynamic voltage restorer (DVR) based on the proposed noninverting buck–boost converter is described. It enables to solve the voltage sag and swell problems by utilizing both positive and negative gains of converter. Then, the hardware prototype of proposed ac–ac converter and DVR are implemented to verify their practical effectiveness. [ABSTRACT FROM AUTHOR]

In this article, we present a new type of Z-source inverter (ZSI) that replaces two inductors in the original quasi-ZSI with two transformers. It can produce a very high output voltage with the high value of the modulation index. Moreover, it enables both to provide a better power quality of output and to reduce the switching loss. In particular, the proposed quasi-clamped ZSI with two transformers give a unique solution to obtain high gain by reducing the turns ratio, rather than increasing it. Also, the leakage inductance of the transformer might cause huge voltage spikes across the inverter bridge. To deal with this problem, an effective clamping technique is proposed. As a result, this increases the overall efficiency of the system by utilizing the low-power switching devices. The characteristics of the proposed quasi-clamped ZSI with two transformers are comprehensively discussed with the detailed theoretical analysis. Thereafter, its performances are evaluated by both simulation and experimental tests. [ABSTRACT FROM AUTHOR]

This paper presents design and control methods for fault-tolerant operations with redundant converter modules, one of the most prominent features in modular multilevel converter (MMC) topology. In fully implementing MMC functionalities, a nearest level control is applied as a low-switching modulation method. A dual sorting algorithm is newly proposed for effectively reducing the switching commutations of each power module as well as for voltage balancing control. Built upon these primary MMC topological and control features, its redundant operation is comprehensively investigated for fail-safe energy transfer. In particular, a novel spare process is proposed to handle an emergency situation when the number of faulty power modules exceeds the module redundancy. Since topological redundancy may cause the switching commutations of power modules in an arm to be unevenly distributed, a practical and effective mitigation measure is incorporated to keep the energy balance while avoiding the undesired switching stresses. Rigorous simulation studies for MMC and its application for high-voltage direct current are performed to demonstrate the validity and effectiveness of the proposed spare process under normal and emergency conditions. [ABSTRACT FROM AUTHOR]