Search

This investigation is centered around the application of warm mix asphalt (WMA) technologies to address workability concerns linked to rubberized asphalt binders. The primary aim of incorporating crumb rubber (CR) and WMA additives is to establish a robust paving method that fosters energy conservation, efficient waste management, noise reduction, and improved overall performance. The current study aims to comprehensively characterize and differentiate the physical attributes of rubberized asphalt binders by employing three distinct WMA additives: Sasobit, Cecabase RT and Rediset WMX. These additives are introduced into eight unique asphalt binders. Laboratory assessments are carried out to evaluate the workability and physical properties of these binders. The evaluation encompasses penetration, softening point, penetration index, penetration viscosity number, storage stability, ductility, viscosity, and stiffness modulus analyses. The findings indicate that the rubberized asphalt binder enhanced with Sasobit demonstrates the highest levels of both hardness and softening point in comparison to asphalt binders supplemented with alternative WMA additives. The evaluation of storage stability underscores the satisfactory stability across all modified asphalt binders. Both the unmodified and modified binders meet the requirements stipulated by the ductility test; the rubberized asphalt binder modified with Rediset falls short. The rubberized asphalt binder improved with Sasobit displays the most notable enhancement in workability. Furthermore, the blend of crumb rubber and Sasobit binder reveals the highest stiffness modulus values under conditions of intermediate and high temperatures with 1.88 and 0.46 MPa, respectively. In summation, the rubberized asphalt binder incorporating crumb rubber with Sasobit showcases superior improvements in both stiffness and workability compared to counterparts modified with Cecabase RT and Rediset WMX.

Researchers across the globe have explored several alternatives to recycling natural rubber and have identified several challenges. Therefore, this study evaluates the feasibility of recycling waste latex rubber gloves (WLRG) as a bitumen modifier to enhance the bitumen’s physical, thermal, and morphological characteristics. The study adds varying percentages of WLRG (3%, 5%, 7%, and 9%) to the 60/70 bitumen and analyzes them to determine the optimum WLRG percentage. The penetration, softening point, ductility, and viscosity tests of the modified binders show a consistent pattern. All WLRG-modified bitumens are stable storage blends at high temperatures. The thermal characteristics of the WLRG particles in the modified bitumen are examined through thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The ogive graph shows that the weight loss of the bitumen modified with 3%, 5%, 7%, and 9% WLRG occurred at 457.5, 464.3, 462.2, and 459.5°C. The maximum weight loss of the control sample occurred at 465.6°C when the environment switched from nitrogen (N2) to air. The DSC graph reveals the changes in the structure or physiochemical processes of the WLRG. The melting point for the binders modified with 3%, 5%, 7%, and 9% WLRG is 133.6, 132.1, 103.5, and 133.2°C. The morphological characteristics were determined using atomic force microscopy (AFM). The bee structure gives a scientific explanation of the microstructural characteristics. A contact angle test was performed to identify the wettability of the sessile drop device by using three types of solvent, namely distilled water, formamide, and glycerol. The contact angle of water showed a decreasing trend, where the binder containing 9% WLRG had the lowest contact angle. For the control sample, the contact angles of formamide and glycerol are 73.95° and 71.85°, respectively. In summary, WLRG is a suitable bitumen modifier and can enhance the physical, thermal, and morphological characteristics of the asphalt binder.

The compacting and mixing processes involving hot mix asphalt during asphalt production can lead to air pollution as a result of a high volatile organic compound. An alternative solution that can reduce greenhouse gas emissions is by using warm mix asphalt (WMA). A proper application of additives to the WMA can improve the asphalt mixture's strength, durability, and workability. In this study, a 60/70 grade asphalt binder was added with 5% of crumb rubber (CR) and three different WMA additives at the recommended dosages, namely Sasobit, Cecabase, and Rediset. The wet method was used to blend the additives with virgin asphalt binders. The mixing and compacting temperatures were set at 135°C and 125°C, respectively, to mix the asphalt mixture. Mechanical performance tests were performed to evaluate the impact of WAM additives with CR on asphalt mixture. Based on the results, all the modified asphalt mixtures showed a better mechanical performance than the virgin asphalt mixture in terms of indirect tensile strength, moisture resistance, permanent deformation, and stiffness. Among all the WMA additives, Sasobit with CR showed the most significant impact on the asphalt mixture's performance.

This study was conducted to investigate the effect of ageing on bitumen, before and after modification. Nano-clay modified bitumen (NCMB) was produced by adding nano-clay (NC) to 60/70 penetration grade bitumen; then, the binder was tested using conventional tests for properties such as penetration, softening point and viscosity. These tests were carried out on the modified binder before and after ageing. A rolling thin film oven (RTFO) was used to simulate short-term ageing (STA), and a pressure ageing vessel (PAV) was used to simulate long-term ageing (LTA) for the modified binder. After initial results showed an improvement for the modified bitumen regarding the effect of ageing, the investigation continued using Fourier transform infrared spectroscopy (FTIR), where the microstructure distribution of the modified binder before and after ageing was observed. Finally, there was no doubt that the effect of ageing on mixtures should be investigated. For this step, the indirect tensile strength (ITS) test, which highlights the strength changes that occur for the mixtures after ageing, was selected. The results indicated that the tensile strength of mixtures made with modified bitumen showed better resistance against ageing when NC was added, which is in good agreement with the results of previous binder tests. The results of this study show that the modification of bitumen using nano-clay as an additive improves the ageing resistance of the binder, which is consequently reflected in the strength of the asphalt mixture.

The reclaimed asphalt pavement (RAP) has become a moderately common practice in most countries; Hence, rejuvenating materials with RAP have earned publicity in the asphalt manufacturers, mainly due to the increasing raw material costs. In this study, the crumb rubber (CR) and waste frying oil (WFO) utilized as waste materials to restore the properties and enhance the rutting resistance of the RAP. Several physical, rheological, chemical properties of bituminous binders were tested. The result showed that the RAP bituminous binders incorporating WFO and CR decreased softening points and the increased penetration value; these translate to an increase in penetration index. Moreover, the viscosity of the WFO/CR combination reclaimed asphalt pavement binder showed better workability and stiffness, as well as a low storage stability temperature (less than 2.2 °C) with an acceptable loss upon heating. Without chemical reaction was observed between the waste-frying oil with the rubberized binder and the reclaimed asphalt pavement binder. Additionally, the WFO/CR rheological properties combined with the reclaimed asphalt pavement binder were comparable to the control sample. The incorporation of CR with WFO as a hybrid rejuvenator enhanced the rutting resistance. Therefore, the presence of WFO/CR has a considerable influence on the RAP binder properties while preserving a better environment and reducing pollution by reusing waste materials.

Researchers are exploring the utilisation of reclaimed asphalt pavement (RAP) as a recycled material to determine the performance of non-renewable natural aggregates and other road products such as asphalt binder, in the construction and rehabilitation stage of asphalt pavements. The addition of RAP in asphalt mixtures is a complex process and there is a need to understand the design of the asphalt mixture. Some of the problems associated with adding RAP to asphalt mixtures are moisture damage and cracking damage caused by poor adhesion between the aggregates and asphalt binder. There is a need to add rejuvenators to the recycled mixture containing RAP to enhance its performance, excepting the rutting resistance. This study sought to improve asphalt mixture performance and mechanism by adding waste frying oil (WFO) and crumb rubber (CR) to 25 and 40% of the RAP content. Moreover, the utilisation of CR and WFO improved pavement sustainability and rutting performance. In addition, this study prepared five asphalt mixture samples and compared their stiffness, moisture damage and rutting resistance with the virgin asphalt. The results showed enhanced stiffness and rutting resistance of the RAP but lower moisture resistance. The addition of WFO and CR restored the RAP properties and produced rutting resistance, moisture damage and stiffness, which were comparable to the virgin asphalt mixture. All waste and virgin materials produce homogeneous asphalt mixtures, which influence the asphalt mixture performance. The addition of a high amount of WFO and a small amount of CR enhanced pavement sustainability and rutting performance.