Search

The Extreme Ultraviolet Imager (EUI) instrument for the Solar Orbiter mission will image the solar corona in the extreme ultraviolet (17.1 nm and 30.4 nm) and in the vacuum ultraviolet (121.6 nm). It is composed of three channels, each one containing a telescope. Two of these channels are high resolution imagers (HRI) at respectively 17.1 nm (HRI-EUV) and 121.6 nm (HRI-Ly∝), each one composed of two off-axis aspherical mirrors. The third channel is a full sun imager (FSI) composed of one single off-axis aspherical mirror and working at 17.1 nm and 30.4 nm alternatively. This paper presents the optical alignment of each telescope. The alignment process involved a set of Optical Ground Support Equipment (OGSE) such as theodolites, laser tracker, visible-light interferometer as well as a 3D Coordinates Measuring Machine (CMM). The mirrors orientation have been measured with respect to reference alignment cubes using theodolites. Their positions with respect to reference pins on the instrument optical bench have been measured using the 3D CMM. The mirrors orientations and positions have been adjusted by shimming of the mirrors mount during the alignment process. After this mechanical alignment, the quality of the wavefront has been checked by interferometric measurements, in an iterative process with the orientation and position adjustment to achieve the required image quality.

The Extreme Ultraviolet Imager (EUI) instrument for the Solar Orbiter mission will image the solar corona in the extreme ultraviolet (17.1 nm and 30.4 nm) and in the vacuum ultraviolet (121.6 nm) spectral ranges. The development of the EUI instrument has been successfully completed with the optical alignment of its three channels’ telescope, the thermal and mechanical environmental verification, the electrical and software validations, and an end-toend on-ground calibration of the two-units’ flight instrument at the operating wavelengths. The instrument has been delivered and installed on the Solar Orbiter spacecraft, which is now undergoing all preparatory activities before launch.

Large reflectors and antennas for the IR to mm wavelength range are being planned for many Earth observation and astronomical space missions and for commercial communication satellites as well. Scientific observatories require large telescopes with precisely shaped reflectors for collecting the electro-magnetic radiation from faint sources. The challenging tasks of on-ground testing are to achieve the required accuracy in the measurement of the reflector shapes and antenna structures and to verify their performance under simulated space conditions (vacuum, low temperatures). Due to the specific surface characteristics of reflectors operating in these spectral regions, standard optical metrology methods employed in the visible spectrum do not provide useful measurement results. The current state-of-the-art commercial metrology systems are not able to measure these types of reflectors because they have to face the measurement of shape and waviness over relatively large areas with a large deformation dynamic range and encompassing a wide range of spatial frequencies. 3-D metrology (tactile coordinate measurement) machines are generally used during the manufacturing process. Unfortunately, these instruments cannot be used in the operational environmental conditions of the reflector. The application of standard visible wavelength interferometric methods is very limited or impossible due to the large relative surface roughnesses involved. A small number of infrared interferometers have been commercially developed over the last 10 years but their applications have also been limited due to poor dynamic range and the restricted spatial resolution of their detectors. These restrictions affect also the surface error slopes that can be captured and makes their application to surfaces manufactured using CRFP honeycomb technologies rather difficult or impossible. It has therefore been considered essential, from the viewpoint of supporting future ESA exploration missions, to develop and realise suitable verification tools based on infrared interferometry and other optical techniques for testing large reflector structures, telescope configurations and their performances under simulated space conditions. Two methods and techniques are developed at CSL. The first one is an IR-phase shifting interferometer with high spatial resolution. This interferometer shall be used specifically for the verification of high precision IR, FIR and sub-mm reflector surfaces and telescopes under both ambient and thermal vacuum conditions. The second one presented hereafter is a holographic method for relative shape measurement. The holographic solution proposed makes use of a home built vacuum compatible holographic camera that allows displacement measurements from typically 20 nanometres to 25 microns in one shot. An iterative process allows the measurement of a total of up to several mm of deformation. Uniquely the system is designed to measure both specular and diffuse surfaces.

Proba-V payload is a successor of the Vegetation instrument, a multispectral imager flown on Spot-4 and subsequently on Spot-5, French satellites for Earth Observation and defence. The instrument, with its wide field of view, is capable of covering a swath of 2200 km, which, in combination with a polar low Earth orbit, guarantees a daily revisit. The lifetime of Spot-5 expires in early 2013, and to ensure the continuity of vegetation data, BELSPO, the Belgian Federal Science Policy Office, supported the development of an instrument that could be flown on a Proba type satellite, a small satellite developed by the Belgian QinetiQ Space (previously known as Verhaert Space). The challenge of this development is to produce an instrument responding to the same user requirements as Vegetation, but with an overall mass of about 30 kg, while the Vegetation instrument mass is 130 kg. This development had become feasible thanks to a number of new technologies that have been developed since the nineties, when Vegetation was first conceived, namely Single Point Diamond Turning fabrication of aspherical mirrors and efficient VNIR and SWIR detectors. The Proba-V payload is based on three identical reflective telescopes using highly aspherical mirrors in a TMA (Three Mirrors Anastigmat) configuration. Each telescope covers a field of view of 34° to reach the required swath. One of the challenges in the development of the PROBA-V instrument is the efficient reduction of stray light. Due to the mass and volume constraints it was not possible to implement a design with an intermediate focus to reduce the stray light. The analysis and minimization of the in-field stray light is an important element of the design because of the large FOV and the surface roughness currently achievable with the Single Point Diamond Turning. This document presents the preliminary baffle layout designed for the Three Mirrors Anastigmatic (TMA) telescope developed for the Proba-V mission. This baffling is used to avoid 1st order stray light i.e. direct stray light or through reflections on the mirrors. The stray light from the SWIR folding mirror is also studied. After these preliminary analyses the mechanical structure of the TMA is designed then verified in term of vignetting and stray light.

The “Association de Satellites Pour l'Imagerie et l'Interferometrie de la Couronne Solaire”, ASPIICS, selected by ESA for the PROBA-3 mission, heralds the next generation of coronagraph for solar research, exploiting formation flying to gain access to the inner corona under eclipse-like conditions for long periods of time. A detailed description of the ASPIICS instrument and of its scientific objectives can be found in [1]. ASPIICS is distributed on the two PROBA 3 spacecrafts (S/C) separated by 150 m. The coronagraph optical assembly is hosted by the “coronagraph S/C” protected from direct solar disk light by the occulting disk on the “occulter S/C”. The most critical issue in the design of a solar coronagraph is the reduction of the stray light due to the diffraction and scattering of the solar disk light by the occulter, the aperture and the optics. In the present article, we deal with two of these issues: - The analysis of the stray light inside the telescope. - The optimization of the external occulter edge, in order to eliminate the Poisson spot behind the occulter and to lower the stray light level going through the entrance pupil of the telescope. This work was performed in the framework of the ESA STARTIGER program which took place at the Laboratoire d’Astrophysique de Marseille (LAM) during a 6-month period from September 2009 to March 2010. In general, it is a very complicated task to combine the above two stray light issues together in the simulation and design phase as it requires to consider the propagation inside the telescope of the light diffracted by the external occulter. Actually, the present literature only reports diffraction calculations performed for simple occulting systems (i.e., two disks and serrated disk). A more pragmatic approach, also driven by the tight schedule of the STARTIGER program, is to separate the two contributions, and perform two different stray light analyses. This paper is dedicated to the description of both analyses: in particular, the first part is dedicated to the evaluation of the stray light inside the telescope, assuming a simple disk as occulter, and a preliminary baffle design is presented; the second part describes the investigation on the geometry of the external occulter, with a detailed description of the laboratory setup that has been designed and implemented to compare together several types of occulting systems.

International audience; The Extreme Ultraviolet Imager (EUI) is one of the remote sensing instruments on-board the Solar Orbiter mission. It will provide dual-band full-Sun images of the solar corona in the extreme ultraviolet (17.1 nm and 30.4 nm), and high-resolution images of the solar disk in both extreme ultraviolet (17.1 nm) and vacuum ultraviolet (Lyman-alpha 121.6 nm). The EUI optical design takes heritage of previous similar instruments. The Full Sun Imager (FSI) channel is a single-mirror Herschel design telescope. The two High Resolution Imager (HRI) channels are based on a two-mirror optical refractive scheme, one Ritchey-Chretien and one Gregory optical design for the EUV and the Lyman-alpha channels, respectively. The spectral performances of the EUI channels are obtained thanks to dedicated mirror multilayer coatings and specific band-pass filters. The FSI channel uses a dual-band mirror coating combined with aluminum and zirconium band-pass filters. The HRI channels use optimized band-pass selection mirror coatings combined with aluminum band-pass filters and narrow band interference filters for Lyman-alpha. The optical performances result from accurate mirror manufacturing tolerances and from a two-step alignment procedure. The primary mirrors are first co-aligned. The HRI secondary mirrors and focal planes positions are then adjusted to have an optimum interferometric cavity in each of these two channels. For that purpose a dedicated alignment test setup has been prepared, composed of a dummy focal plane assembly representing the detector position. Before the alignment on the flight optical bench, the overall alignment method has been validated on the Structural and Thermal Model, on a dummy bench using flight spare optics, then on the Qualification Model to be used for the system verification test and qualifications.

International audience; The Extreme Ultraviolet Imager (EUI) on-board the Solar Orbiter mission will provide full-sun and high-resolution image sequences of the solar atmosphere at selected spectral emission lines in the extreme and vacuum ultraviolet. After the breadboarding and prototyping activities that focused on key technologies, the EUI project has completed the design phase and has started the final manufacturing of the instrument and its validation. The EUI instrument has successfully passed its Critical Design Review (CDR). The process validated the detailed design of the Optical Bench unit and of its sub-units (entrance baffles, doors, mirrors, camera, and filter wheel mechanisms), and of the Electronic Box unit. In the same timeframe, the Structural and Thermal Model (STM) test campaign of the two units have been achieved, and allowed to correlate the associated mathematical models. The lessons learned from STM and the detailed design served as input to release the manufacturing of the Qualification Model (QM) and of the Flight Model (FM). The QM will serve to qualify the instrument units and sub-units, in advance of the FM acceptance tests and final onground calibration.

The Sun Watcher with Active Pixel System detector and Image Processing (SWAP) telescope was launched on 2 November 2009 onboard the ESA PROBA2 technological mission and has acquired images of the solar corona every one - two minutes for more than two years. The most important technological developments included in SWAP are a radiation-resistant CMOS-APS detector and a novel onboard data-prioritization scheme. Although such detectors have been used previously in space, they have never been used for long-term scientific observations on orbit. Thus SWAP requires a careful calibration to guarantee the science return of the instrument. Since launch we have regularly monitored the evolution of SWAP detector response in-flight to characterize both its performance and degradation over the course of the mission. These measurements are also used to reduce detector noise in calibrated images (by subtracting dark-current). Since accurate measurements of detector dark-current require large telescope off-points, we have also monitored straylight levels in the instrument to ensure that these calibration measurements are not contaminated by residual signal from the Sun. Here we present the results of these tests, and examine the variation of instrumental response and noise as a function of both time and temperature throughout the mission., 29 pages, 29 (colour) figures, 2 tables

PROBA-3 is a technology mission devoted to the in-orbit demonstration of formation flying techniques and technologies. PROBA-3 will implement a giant coronagraph (called ASPIICS) that will both demonstrate and exploit the capabilities and performances of formation flying. ASPIICS is distributed on two spacecrafts separated by 150m, one hosting the external occulting disk and the other the optical part of the coronagraph. This part implements a three-mirror-anastigmat (TMA) telescope. Its pupil is placed about 800mm in front of the primary mirror, a solution allowing an efficient baffling and a high reduction of the stray light inside the instrument. A complete stray light analysis of the TMA has been carried out to design the baffles and to establish the required roughness of the mirrors. The analysis has been performed in two steps: first, by calculating the diffraction pattern behind the occulter due to an extended monochromatic source having the diameter of the Sun; second, by propagating this diffraction pattern, through all the telescope optical components, to the prime focal plane. The results obtained are described in this article.

The next generation of infrared - sub mm space telescopes requires reflectors with large dimensions, high quality and, according to weight issues, are based on composite or new materials technology. The challenging tasks of on-ground testing are to achieve the required accuracy in the measurement of these reflectors shape and antenna structures and to verify their performance under simulated space conditions (vacuum, low-high temperatures). A holographic camera for the verification and validation of this type of reflector in a space environment is presented. A diffuser is implemented to measure the deformations of reflective surfaces in a more flexible way. The system has been made compatible with the vacuum conditions. Some elements of the holographic camera (camera lenses, CCD, crystal, optical fibre) have been adapted and tested under vacuum. The metrological certification of the whole system is realised by the measurement of a parabolic CFRP reflector with a 1.1 meter diameter. The results are compared to the one achieved with a high spatial resolution IR interferometer on the same reflector in laboratory conditions and under thermal vacuum conditions. This later test consists in measuring the deformations of the reflector between an initial state at a selected temperature and a final state at another temperature. The comparison between the high spatial resolution IR interferometer and this dynamic holographic method showed very good qualitative and quantitative agreement between the techniques, thus verifying the potential of this new Holographic approach.