Search

From Obsidian silicate, in its natural form, pellets were manufactured adding Teflon to the material in powder. These pellets were exposed to the gamma radiation beams of a 60Co source in a dose interval from 10 Gy to 10 kGy. The Obsidian in powder was investigated in relation to its physical and chemical characteristics, by means of the X-ray diffraction, scanning electronic microscopy and energy-dispersive X-ray spectroscopy techniques. After the irradiation procedure, the signal of the samples was evaluated by means of three techniques: thermoluminescence (TL), optically stimulated luminescence (OSL) and thermally stimulated exoelectron emission (TSEE). The objective of this work was to verify the TL, OSL and TSEE response of the Obsidian+Teflon pellets after exposure to high doses of gamma radiation. Different response characterization tests were performed, as TL and TSEE emission curves, OSL signal decay, reproducibility, dose-response curves, lower detection limits and fading. From these results, it can be observed that the Obsidian+Teflon pellets present good conditions to be used as high dose gamma radiation detectors; the results obtained with the OSL technique were the most adequate in terms of response in function of absorbed dose. The fading of the signals, varying from about 26% (TSEE) to 44% (OSL), in a time interval of 360 h post-irradiation, also showed favorable results for the use of this material as radiation detector, when the measurements are taken after a defined time interval.

Spectrolite + Teflon and Opal + Teflon pellets were studied in this work in relation to their dosimetric properties, using the thermally stimulated exoelectron emission (TSEE) phenomenon. The purpose of this work was to study these materials to be used in high-dose dosimetry of 60Co irradiators, which are employed for several industrial applications. The basic physical principle of this technique is the emission of low energy electrons from the surface of different crystals. For this reason, it is very employed in work with specially radiation sources of low penetrating power, as alpha and beta radiation, but also with gamma sources. Both materials had already their dosimetric chatacteristics verified in previous works after exposure to high doses of a 60Co source and measurements by means of thermoluminescence (TL) and optically stimulated luminescence (OSL) techniques. The TSEE response was investigated in terms of the following tests: TSEE emission curves, reproducibility, minimum detectable doses and dose-response curves.

In this work, the response of the natural material Opal was studied in relation to its thermoluminescence (TL) and optically stimulated luminescence (OSL), after exposure to the gamma radiation of a 60 Co source. The structure of the powdered Opal was verified using the X-ray diffraction, scanning electronic microscopy and energy-dispersive X-ray spectroscopy techniques. The material, in its stone form, was turned into powder and mixed to Teflon (also in powder) in three different concentrations, and then pellets were manufactured. The aim of this work was to evaluate the response of these pellets in high-doses of gamma radiation beams, and to observe their possible application as dosimeters, using the TL and OSL techniques. The dosimetric properties of the samples were analyzed by means of different tests, as: TL emission curves and OSL signal decay curves, reproducibility of TL and OSL response, minimum detectable dose, TL and OSL dose–response curves (5 Gy–10 kGy), and fading. The results obtained in this work, for the TL and OSL phenomena, demonstrated that the pellets of Opal + Teflon present an adequate performance e possibility of use as dosimeters in beams of high-dose gamma radiation.

The Spectrolite, from the silicate family, a variety of Labradorite, was already studied in relation to its thermoluminescence (TL) and optically stimulated luminescence (OSL) responses, in high-dose gamma radiation fields; the results indicated their good application as gamma radiation detectors. In the present work, the analyses performed to investigate powdered Spectrolite are presented, by means of the XRD, SEM and EDX techniques. The luminescent behavior of Spectrolite + Teflon samples, in the concentration of 1:1, was studied in beta radiation beams (90Sr + 90Y), using the luminescent phenomena of TL and OSL. The results showed adequate TL and OSL reproducibility of the samples; the dose–response curves for both techniques presented a linear behavior in a range from 0.5 Gy to 1 kGy, and the fading showed that after 150 h there were 46.7% and 31.6% of the remaining signal of samples for TL and OSL responses, respectively. Therefore, the Spectrolite + Teflon pellets may be used in beta radiation dosimetry.

The thermoluminescence (TL) and infrared stimulated luminescence (IRSL) responses of in-house produced CaF2:Tm dosimeters are investigated in this work, envisaging their application in electron beam (EB) radiation processing. The irradiations were performed at an industrial EB accelerator (1.5 MeV) covering a dose rate range of 2–8 kGy/s and dose up to 10 kGy. In general, the TL glow curves display four peaks, termed as peaks 2, 3, 4, and 5, corresponding to temperatures at ~150, 200, 240, and 300 °C, respectively. The intensity of the low-temperature peaks (2 and 3) grows with the dose, while the others remain constant (saturated). Nevertheless, an evident dose effect on the glow curves manifests in decreased peak3/peak2 ratio with increasing doses. The CW-IRSL curves exhibit similar patterns with an initial signal increase, followed by an exponential decay. Instead of the normal monotonic decays, these peak-shaped curves might be due to the charge capture competition between empty shallow traps and recombination centers. Both TL and IRSL intensities increase linearly with doses up to 6 kGy, and for higher doses, they become sub-linear with a saturation trend around 10 kGy. Another common feature of TL/IRSL response is its dose rate dependence, being more sensitive at higher dose rates. Despite being dose-rate dependent, the CaF2:Tm dosimeters might be suitable for EB processing dosimetry. However, for their use as routine dosimeters, relevant dosimetric characteristics, such as fading and response reproducibility, have to be investigated. Work in this direction is underway.

A natural material called spectrolite, from Finland, was studied in this work. The purpose was to test it in gamma radiation beams to verify its performance as a high-dose detector. From this material, pellets were manufactured with two different concentrations of Teflon and spectrolite, and their responses were verified using two luminescent techniques: thermoluminescence (TL) and optically stimulated luminescence (OSL). The TL and OSL signals were evaluated by means of characterization tests of the material response, after exposure to a nominal absorbed dose interval of 5 Gy to 10 kGy. The results obtained, for both concentrations, showed a good performance of this material in beams of high-dose gamma radiation. Both techniques were utilized in order to investigate the properties of the spectrolite+Teflon samples for different applications.

MgB4O7 doped with lanthanides such as Dy3+ and Tm3+ are phosphors with very well established use in routine personal dosimetry. Certain characteristics, for example linearity in a broad dose range, low energy dependence, Z(eff)=8.5, high sensitivity and a relatively simple thermoluminescent (TL) emission curve make MgB4O7 a good material for thermoluminescent dosimetry. With the aim of analyzing other doping possibilitis, this paper presents some preliminary results on the use of Nd3+ as a dopant in the MgB4O7 matrix. Furthermore, we evaluated the effect of using two different lanthanides, Nd and Dy, in the host matrix. In the present work, the phosphors were produced through solid state synthesis and X-ray diffraction confirmed the success of the technique. The TL behavior of MgB4O7:Nd was assessed when irradiated with gamma (Co-60) and beta radiation, to determine the effect of the dopant concentration and the dose-response over a broad dose range. We also evaluated the dose-response of MgB4O7:Nd,Dy when irradiated with Co-60. The TL responses of the phosphors were compared with that of MgB4O7:Dy. These preliminary studies show that for the absorbed dose range studied, the sensitivity of MgB4O7:Nd,Dy was 3.8 and 28 times higher than that of MgB4O7:Dy and MgB4O7:Nd. The materials also presented linearity from 5 to 40 Gy. Above this value, the dose response curve exhibited sublinear behavior. These preliminary results will assist in developing a new temperature sensor based on a MgB4O7 dosimeter. (C) 2014 Elsevier B.V. All rights reserved.

This work evaluates the dosimetric properties of crystals of CaSO 4 doped with unusual elements, such as europium (Eu) and silver (Ag), including their nanoparticle forms, after the incorporation of glass or Teflon and compares them with well-known thermoluminescent dosimeters (TLD). X-ray diffraction analyses showed that samples of doped CaSO 4 exhibit only a single phase corresponding to the crystal structure of anhydrite. Optical spectroscopy confirmed the presence of Eu 3+ in the crystal matrix and a luminescent gain due the presence of silver nanoparticles. The composites showed thermoluminescent emission glow curves, with a single peak centered at approximately 200 °C for pellets with Teflon and at 230 °C for pellets with glass. The dosimeters based on calcium sulfate doped with europium and silver nanoparticles provided the most intense thermoluminescent (TL) emission of the composites studied. In comparison with commercial TLD, such as LiF:Mg,Ti and CaSO 4 :Dy, the CaSO 4 :Eu,Ag(NP)+glass produced in this work presented similar low detection limits and higher sensitivity. The new methods for the preparation of dosimeters and the incorporation of glass are shown to be viable because all of the samples presented a linear, reproducible and first order kinetic TL emission.

MgB4O7 is a promising matrix host for use in radiation dosimetry due to its low effective atomic number (Zeff = 8.2). The present work aims to investigate dosimetric and luminescent properties of the MgB4O7:Ce0,5%,Li0.5%, produced through solid-state synthesis, using the optically stimulated luminescence (OSL) technique. The first part of this work discusses the luminescent aspects of this phosphor, such as thermoluminescent emission spectra, photoluminescence emission, lifetime of emission centers and the effect of different lithium concentrations as co-dopant. In the second part, the basic OSL properties were evaluated, including dose-response curve, minimum detectable dose (MDD), step annealing, and best bleaching set-up for reuse of MgB4O7:Ce0,5%Li0.5% composites. The photoluminescence and thermoluminescence emission spectra of the composites present an emission peak at UV-VIS range centered around 370 nm, which is the most suitable for OSL dosimetry; this emission is related to Ce3+ electronic transitions and has a luminescence center lifetime of 0.003 ms. From the step-annealing analyses, it can be seen that the OSL emission is related to different depth trap centers in the band gap. The OSL dose-response curve is linear from 0.1 Gy to 100 Gy, with a MDD around 1 mGy. These properties make this material a strong candidate for different applications in radiation dosimetry field.

Beta radiation emitters have been intensively used in therapeutic protocols, causing the increase of the radiation exposure of the workers. The thermoluminescent (TL) technique is largely utilized for the monitoring of beta radiation doses of workers. However, recently, the optical stimulated luminescence (OSL) technique has been shown useful for individual dosimetry and for beta radiation. In this study, the results obtained using Al2O3:C (OSL) and CaSO4:Dy (TL) detectors to measure beta absorbed doses inside a glove box at a radiopharmacy laboratory were compared.

Devido à inexistência de um laboratório de padronização primária na América Latina, para calibração e dosimetria de fontes de radiação beta, neste trabalho uma câmara de extrapolação Böhm foi caracterizada e estabelecida como um sistema padrão primário no Laboratório de Calibração de Instrumentos (LCI) do IPEN. Como objetivo principal deste trabalho, a câmara de extrapolação Böhm foi caracterizada com relação à sua resposta em feixes padrões secundários de radiação beta de fontes de 90Sr+90Y, com duas janelas de entrada diferentes: Mylar aluminizado e Hostaphan grafitado, e com dois métodos de determinação de taxa de dose absorvida, para verificação do seu desempenho com cada material. Embora se trate do instrumento mais adequado para a calibração de detectores e fontes de radiação beta, a câmara de extrapolação deve ser utilizada apenas em laboratórios de calibração e não em programas de controle de qualidade, pois ela tem 7 kg e é de alto custo. Assim, é importante ter sistemas considerados padrões de trabalho e métodos alternativos para substituir a câmara de extrapolação em medições realizadas em campo, como em hospitais ou clínicas. Por este motivo, foram caracterizadas três câmaras de ionização de placas paralelas, com o objetivo de se verificar a possibilidade de seu uso como sistemas padrões de trabalho em programas de controle de qualidade, e também foram estudados materiais dosimétricos diferentes, em campos de radiação beta de 90Sr+90Y, utilizando-se os fenômenos da termoluminescência (TL) e da luminescência opticamente estimulada (LOE), como métodos alternativos na calibração de fontes de radiação beta. Inclui-se aqui o desenvolvimento de um sistema postal dosimétrico para a calibração de aplicadores clínicos de 90Sr+90Y. Os resultados obtidos com a câmara de extrapolação Böhm permitiram o seu estabelecimento como sistema padrão primário na calibração de fontes de 90Sr+90Y, pois a câmara com as duas janelas de entrada diferentes permitiram a determinação de taxas de dose absorvida no ar e no tecido, à profundidade nula e a 0,07 mm. A caracterização das três câmaras de ionização de placas paralelas mostraram que elas podem ser usadas em programas de controle de qualidade de fontes de radiação beta, pois suas respostas se apresentaram adequadas para esta finalidade. Os materiais dosimétricos testados com relação às suas respostas TL e LOE também se mostraram adequados para uso em campos de radiação beta, pois suas respostas foram satisfatórias. O sistema dosimétrico, utilizando dosímetros TL, foi testado em hospitais e, posteriormente, foi enviado na forma postal a um laboratório, contendo detectores TL e LOE, e o resultado da calibração dos aplicadores clínicos foi adequado. Due to the lack of a primary standard laboratory at the Latin America, for the calibration and dosimetry of beta radiation sources, it was decided to establish the Böhm extrapolation chamber at the Calibration Laboratory (LCI) at IPEN as a primary standard. As a main objective of this work, the Böhm extrapolation chamber was characterized in relation to its response in beta radiation secondary standard beams of 90Sr+90Y sources, using two different entrance windows: aluminized Mylar and graphited Hostaphan, and using two methods of determination of absorbed dose rates, to verify its performance in each material. Although it is the most adequate instrument for the calibration of beta radiation detectors and sources, the extrapolation chamber should only be used at calibration laboratories, and not in quality control programs, because it weights 7 kg, and it is expensive. Thus, it is important to have systems considered work standards and alternative methods to replace the extrapolation chamber in measurements performed outside laboratories, such as in hospitals and clinics. For this reason, three parallel plate ionization chambers were characterized, with the objective to verify the possibility of their use as work standard systems, and different dosimetric materials were also studied, in beta radiation fields, using the thermoluminescence (TL) and optically stimulated luminescence (OSL) phenomena, as alternative methods for the calibration of beta radiation sources. The development of a dosimetric postal system for the calibration of 90Sr+90Y clinical applicators was included in this objective. The results obtained using the Böhm extrapolation chamber allowed its establishment as a primary standard system at the calibration of 90Sr+90Y sources, because it was possible to determine the absorbed dose rates in air and in the tissue, at null depth and 0.07 mm using the chamber with the two different entrance windows. The characterization of the three parallel plate ionization chambers showed that they can be used in quality control programs of beta radiation sources, because their responses were adequate to this purpose. The dosimetric materials were tested in relation to their TL and OSL response, and their use showed also to be adequate in beta radiation fields. The dosimetric postal system, using TL dosimeters, was tested in hospitals, and afterwards, it was sent to a laboratory, by conventional mail, with TL and OSL detectors, and the results of the calibration of the clinical applicators was adequate.

Clinical applicators are used in brachytherapy to treat superficial lesions of skin and eye. They should be periodically calibrated according to quality control programs and international recommendations. Thin CaSO4:Dy thermoluminescent dosimeters were used to calibrate various applicators with a dermatological applicator as a reference. The obtained absorbed dose rates were compared with those quoted in their calibration certificates. Depth-dose curves were constructed for all the applicators. A mail dosimetry system was developed for calibration of clinical applicators.