Search

In this study, we developed a unique defect healing method for 3D printed ceramic compact via cold isostatic pressing (CIP) after debinding, and typical features of interlayer interface defects of 3D‐printed zirconia compact were characterized and found to be reduced significantly. The characteristic sintering kinetics window and microstructure evolution of the healed sintered bodies were systematically investigated, which was found to be quite different from conventional shaping methods. The three sintering stages are probed by their feature microstructure details such as the mechanically flattening surface at the early sintering stage, the heterogeneous microstructure and high porosity in the interlayer interface region at the middle stage, and the slightly ripple‐like structural features combined with the healed interlayer defects at the final stage. The evolution of the pore structure of the healed 3D printed bodies were traced and the mechanical properties such as the Young's modulus, hardness, and fracture toughness were measured to understand the significance of the heal effect. [ABSTRACT FROM AUTHOR]

In this work, a stereolithography-based method of 3D printing was successfully used to fabricate a complex-shaped triangular zirconia cutting tool with a tool withdrawal groove and a honeycomb ceramic component. The sintered bodies displayed significant shrinkage after sintering, with the maximum shrinkage being 35.26%. The XRD pattern indicated that the crystalline phase of the parts was the t-ZrO 2 phase, while SEM characterization revealed that the sintered bodies were composed of densely packed submicron-grade grains, without any discernible pores. The density of the parts was measured as 97.14% via Archimedes’ water displacement method, which is consistent with the results of SEM characterization. Additionally, the measured Vickers hardness and fracture toughness of the fabricated parts were 13.0597 GPa and 6.0380 MPa m 1/2 , respectively. These values are close to the structural properties of common zirconia ceramics prepared by conventional approaches. Hence, a novel DLP-stereolithography-based 3D printing process for the fabrication of complex and dense zirconia ceramic parts has been proposed in this work. [ABSTRACT FROM AUTHOR]

We report a novel approach to fabricate dense zirconia-toughened alumina (ZTA) ceramics with excellent properties via an additive manufacturing process based on stereolithography. The XRD patterns show the ZTA sample consists of α-Al 2 O 3 and t-ZrO 2 with the dominance of α-Al 2 O 3 . The zirconia grain with the average size of 0.35 µm is small enough to trigger the toughening behavior of zirconia in the ZTA. The prepared ceramics showed a density, Vickers hardness, bending strength, and fracture toughness of 4.26 g/cm 3 , 17.76 GPa, 530.25 MPa, and 5.72 MPa m 1/2 , respectively. These properties are comparable to those for ceramics obtained through conventional ceramic processing. [ABSTRACT FROM AUTHOR]

In this research, we creatively integrate the traditional methods of liquid precursor infiltration plus in-situ precipitation with stereolithography-based 3D printing for the fabrication of Al 2 O 3 -ZrO 2 ceramics to ensure the homogeneous distribution of ZrO 2 particle in the alumina matrix. Our characterization results shows that this combination leads to the materials with significantly better performance. The Al 2 O 3 specimen is soaked in a Zr 4+ ion solution to induce infiltration, in-situ precipitation and then sintered. X-ray diffraction analysis of the thus-treated sample indicated that Al 2 O 3 was the primary phase and t-ZrO 2 was the secondary phase. Microstructural and EDS analysis showed that the ZrO 2 particles were homogeneously distributed in the Al 2 O 3 matrix, leading to inhibited grain growth. The samples soaked in solutions for different Zr 4+ concentrations and sintered both at 1450 °C and 1550 °C showed improved mechanical properties as compared to those of pure alumina. Futhermore, the sample infiltrated using the solution with a concentration of 1.5 mol/L and sintered at 1450 °C showed similar fracture toughness (4.97 MPa m 1/2 ) with the sample sintered at 1550 °C (5.06 MPa m 1/2 ) but much better hardness (20.95 Gpa) than the sample sintered at 1550 °C (19.71 GPa). Therefore, this method could not only enhance the mechanical properties via introducing the second phase, but also lowers the sintering temperature by at least 100 °C, which would be beneficial for energy conservation and leads to significant advances in the 3D printing of ceramic components. [ABSTRACT FROM AUTHOR]

In this study, Al 2 O 3 ceramics were printed by stereolithography from particles with different particle size distributions, which are the micro-sized Al 2 O 3 , nano-sized Al 2 O 3 , and a mixture of both. The influence of the particle size and the debinding method on the density and morphology of the sintered bodies were investigated. The density of the samples containing both micro-sized and nano-sized alumina particles is highest among the three samples. Furthermore, the samples subjected to the vacuum debinding showed a higher density compared with the samples subjected to the traditional thermal debinding. The results suggest that the combination of a powder with a bimodal particle size distribution and the vacuum debinding process offers an effective way to print 3D ceramics with a good performance through stereolithography. [ABSTRACT FROM AUTHOR]