Search

Background: This study aims to determine phase transformation temperatures of EndoSequence Reciprocating System (ESR), Wave One Gold (WOG), and Reciproc Blue (RB) via differential scanning calorimetry (DSC). Further, to evaluate the cyclic fatigue behaviors by applying static (SF) and dynamic fatigue (DF) tests., Methods: All files' systems were evaluated using DSC (Netzch 200 F3, Germany) with scans ranging from 80°C to -80°C to compare phase transformation. Twenty files from each file system (n = 20) were tested by cyclic fatigue in SF (n = 10) and in DF (n = 10) and the number of cycles to failure (NCF) was calculated for all groups. The files were rotated in a clockwise motion in a metal tube at 350rpm. The NCF was calculated by multiplying the time until fracture in minutes by speed (350 rpm). The NCF was analyzed statistically using a One-Way Analysis of Variance (ANOVA) to determine if there were significant differences among the experimental groups., Results: All files exhibited a single peak in the cooling curve marking martensitic transformation with RB showing martensitic transformation start temperature at around 37 o C . ESR and WOG exhibited single endothermic peaks marking austenitic transformation. RB exhibited two endothermic peaks marking R-phase and austenitic transformations. In cyclic fatigue testing, WOG presented the lowest NCF in DF testing compared to ESR and RB (p < .05) with a nonsignificant difference between the latter two. In the SF, ESR showed a statistically significant larger NCF compared to RB, which also showed statistically significant larger NCF compared to WOG (p < .05)., Conclusions: RB shows martensite transformation start temperature close to body temperature. RB and ESR show improved cyclic fatigue resistance compared to WOG in the SF mode. In the DF mode, WOG showed the lowest cyclic fatigue resistance., Competing Interests: Declarations. Ethics approval and consent to participate: This study was approved by the Research Ethics Committee of the Faculty of Dentistry, King Abdulaziz University, proposal no. 195–12-20. Not Applicable. Competing interests: The authors declare no competing interests., (© 2025. The Author(s).)

This study aims to assess the in vitro durability of Nitinol retainers, manufactured using computer-aided methods with hydrophilic or superhydrophilic surfaces to reduce debonding, alongside a commonly used composite adhesive. The 112 lower incisor teeth were embedded in blocks in pairs. Retainer wires were made up of 0.018 × 0.018 inch Nickel Titanium alloy(G4™ Nickel Titanium G&H Orthodontics, USA) by bending a robot arm. A total of 16 teeth(8 blocks) were used for each of the mentioned 7 groups Ni-Ti Retainer; Laser Textured Ni-Ti Retainer; Laser Texturing and Atmospheric Plasma Applicated Ni-Ti Retainer; Atmospheric Plasma Applicated Ni-Ti Retainer; Laser Texturing and Atmospheric Plasma Applicated Ni-Ti Retainer*2; Laser Texturing and Atmospheric Plasma Applicated Ni-Ti Retainer*3; SS-0.0018"(Morelli, Brazil). Transbond LR(3 M Unitek, California) was used. The shear bond strength tests were conducted. The Kruskal-Wallis H test was employed, pairwise comparisons followed by Dunn's test with Bonferroni correction as a post-hoc analysis. There was no statistically significant difference between the groups for maximum force and maximum stress(p > 0.05). However, a significant difference was found in maximum elongation (p:0.0023). Pairwise comparisons highlighted significantly higher elongation values in the SS-0.0018" group. The stainless-steel wire demonstrated higher elongation values, which may offer clinical advantages in cases with higher occlusal forces and periodontal problems due to its material flexibility. Laser Texturing and Atmospheric Plasma Applied Ni-Ti Retainers exhibited higher test performance. Surface treatments applied to CAD/CAM retainers can provide an advantage by enhancing bond strength, potentially reducing the risk of debonding. These findings underline the importance of material selection and surface treatments in optimizing fixed retention strategies for long-term clinical success., Competing Interests: Declarations. Ethical approval: Here is the English translation of the consent form from Orginal language. Prior to participation, all individuals provided written informed consent after being fully informed about the study’s purpose, procedures, and potential risks. Participation was entirely voluntary, and individuals retained the right to withdraw at any point without penalty. Consent for publication: Not applicable. Competing interests: The authors declare no competing interests., (© 2025. The Author(s).)

Owing to the adverse consequences of excess glucose (Glu) and hydrogen peroxide (H 2 O 2 ) on humans, it is imperative to develop an electrochemical sensor for detection of these analytes with good selectivity and sensitivity. Herein, a nanohybrid comprising nickel cobaltite nanoparticles (NiCo 2 O 4 NPs) embedded on conductive Ti 3 C 2 T x nanosheets (NSs) has been prudently designed and employed for the electrochemical detection of Glu and H 2 O 2 . The developed nanohybrid has been systematically characterized using morphological and spectral techniques, and then immobilized on a glassy carbon electrode (GCE). Under optimized conditions, the developed NiCo 2 O 4 -Ti 3 C 2 T x /GCE based electrochemical sensor has demonstrated an impressive analytical response towards Glu and H 2 O 2 with good sensitivity and selectivity. The non-enzymatic sensor has demonstrated a broad linear range from 30 μM to 1.83 mM for Glu, and two linear ranges of 20-100 μM and 100 μM-2.01 mM for H 2 O 2 . The sensor has exhibited limits of detection (LOD) of 9 μM and 6 μM with sensitivities of 101.2 μA μM -1 cm -2 and 107.03 μA μM -1 cm -2 , respectively, for Glu and H 2 O 2 detection. The impressive analytical performance of the fabricated sensor in terms of linear range, LOD and sensitivity are ascribed to the (i) enhanced conductivity of Ti 3 C 2 T x NSs, (ii) mediated electrocatalytic activity of NiCo 2 O 4 NPs and (iii) large number of catalytically active sites on the NiCo 2 O 4 -Ti 3 C 2 T x heterostructure. Notably, the NiCo 2 O 4 -Ti 3 C 2 T x /GCE has demonstrated impressive stability and reproducibility, which is mainly due to the in situ uniform growth of NiCo 2 O 4 NPs over Ti 3 C 2 T x NSs.

This study investigates the moments generated when applying third-order bends to lingual brackets with different slot shapes and wires made of different materials. Three types of lingual brackets with different slot shapes: 0.018×0.018-inch square slot self-ligation bracket (AL-bracket); 0.018×0.025-inch slot self-ligation bracket (CL-bracket); 0.018×0.025-inch slot self-ligation bracket (ST-bracket). Wires of three different materials were measured. The torque value generated during torque application was measured using a torque gauge. The AL-bracket had a significantly larger torque moment than the CL- and ST-brackets at the same angles. The CL-bracket had the smallest torque moment of the three for the square wire; however, the CL-bracket revealed a larger torque moment than the ST-bracket for the rectangular wire. The torque moment of Ti-Ni wires was observed the smallest. In lingual orthodontic treatment, the results suggested the shape of the lingual bracket slot and the wire material should be considered when adjusting and applying third-order bends.

Nickel-titanium (NiTi) shape memory alloys are promising materials for orthopedic implants due to their unique mechanical properties, including superelasticity and shape memory effect. However, the high nickel content in NiTi alloys raises concerns about biocompatibility and potential cytotoxic effects. This review focuses on the recent advancements in surface modification techniques aimed at enhancing the properties of NiTi alloys for biomedical applications, with particular emphasis on low-temperature glow discharge plasma oxidation methods. The review explores various surface engineering strategies, including oxidation, nitriding, ion implantation, laser treatments, and the deposition of protective coatings. Among these, low-temperature plasma oxidation stands out for its ability to produce uniform, nanocrystalline layers of titanium dioxide (TiO 2 ), titanium nitride (TiN), and nitrogen-doped TiO 2 layers, significantly enhancing corrosion resistance, reducing nickel ion release, and promoting osseointegration. Plasma-assisted oxynitriding processes enable the creation of multifunctional coatings with improved mechanical and biological properties. The applications of modified NiTi alloys in orthopedic implants, including spinal fixation devices, joint prostheses, and fracture fixation systems, are also discussed. Despite these promising advancements, challenges remain in achieving large-scale reproducibility, controlling process parameters, and reducing production costs. Future research directions include integrating bioactive and antibacterial coatings, enhancing surface structuring for controlled biological responses, and expanding clinical validation. Addressing these challenges can unlock the full potential of surface-modified NiTi alloys in advanced orthopedic applications for safer, longer-lasting, and more effective medical implants.

Background: This study compared the torsional resistance, bending stiffness, and cyclic fatigue resistances of different heat-treated NiTi files for minimally invasive instrumentation., Methods: TruNatomy (TN) and EndoRoad (ER) file systems were compared with ProTaper Gold (PG). Torsional load, distortion angle, and bending stiffness were assessed using a custom device AEndoS, and toughness was calculated using the torsional data. Cyclic fatigue resistance was evaluated using another custom device (EndoC) with 45-degree curved canal in which file was rotated until fracture using dynamic pecking motion at 37 °C. One-way analysis of variance and Duncan's post-hoc comparison were conducted at a significance level of 95%. Scanning electron microscopy (SEM) analyzed fracture features and differential scanning calorimetry (DSC) analyzed phase transformation temperatures., Results: ER and TN showed significantly lower torsional strength than PG (p < 0.05). However, ER showed a significantly greater distortion angle and the highest toughness, followed by PG and TN (p < 0.05). Both ER and TN showed similar bending stiffness, which was lower bending stiffness than PG (p < 0.05). ER showed the highest cyclic fatigue resistance (p < 0.05). SEM revealed typical fracture features across all groups, with distinct milling grooves in PG and TN, not in ER. DSC indicated that PG and ER showed a peak of austenite (Ap) at temperatures higher than body temperature, 42 °C and 40 °C, respectively, while TN showed A p at 25 °C., Conclusion: Files for minimally invasive instrumentations typically exhibited high cyclic fatigue resistance but showed differences in the properties. The selection should depend on the root canal and tooth condition., Competing Interests: Declarations. Human ethics and consent to participate: Not applicable. Consent for publication: Not applicable. Competing interests: The authors declare no competing interests., (© 2025. The Author(s).)

The preservation of the original configurations of root canals during endodontic preparation is crucial for treatment success. Nickel-titanium (NiTi) rotary systems have been refined to optimize canal shaping while minimizing iatrogenic errors. This study aimed to evaluate and compare the shaping efficacy of the novel R-Motion (RM) and the established WaveOne Gold (WG) systems using micro-computed tomography (micro-CT). Twenty-four mesial canals of 12 double-rooted extracted mandibular first molars were randomly assigned to either the RM or WG groups, with the mesiobuccal (MB) and mesiolingual (ML) canals allocated accordingly. Root canals were prepared following the manufacturer's protocols. In the RM group, crown-down technique up to a 25/0.06 taper was employed. For the WG group, the preparation was completed with a WG primary file (25/0.07 taper). Specimens were scanned using micro-CT scans before and after instrumentation to establish baseline and post-instrumentation datasets. The following parameters were evaluated, and values were calculated to compare the shaping ability of the two files: percentage of untouched canal walls, changes in surface area, canal volume, dentin thickness, canal angulation, structure model index, canal transportation, and centering ability ratio. Data were analyzed using IBM SPSS Statistics for Windows, Version 23.0 (IBM Corp., Armonk, NY), with a statistical significance set at P ≤ 0.05. Micro-CT analysis demonstrated comparable untouched canal surface areas and changes in surface area and volume between both RM and WG systems. Both systems effectively straightened canal curvature without significant differences in canal angulation. The RM files exhibited a statistically lower reduction in dentin thickness, indicating better preservation of structural integrity. Both RM and WG files displayed similar effective shaping abilities. However, RM caused less dentin removal and canal transportation. Thus, RM is recommended for its ability to balance effective canal shaping with structural preservation in a conservative manner., Competing Interests: Declarations. Ethics approval and consent to participate: All methods were carried out in accordance with relevant guidelines and regulations. All experimental protocols were approved by the Research Ethics Committee of the Faculty of Dentistry, King Abdulaziz University (approval number: 37-02-24). Informed consent was obtained from all subjects and/or their legal guardian(s). Competing interests: The authors declare no competing interests., (© 2024. The Author(s).)

This study focuses on enhancing the performance of photodetector through the utilization of inorganic perovskite material. It emphasizes that the unique properties of perovskite materials contribute to the superior performance of the photodetector. The focus is on the design and enhancement of CsSnI 3 -based photodetector having graphene oxide (GO) and PCBM as charge transport layer, analysing their potential for improved operation. The design process involves a series of optimizations to the device layers, particularly the absorber layer's thickness and defects, which is critical for enhanced efficiency. The designed photodetector exhibits a better responsivity and detectivity in red and near infrared region and maximum responsivity of 0.68 A/W and detectivity of 9 × 10 12 Jones. The SCAPS-1D tool is employed to facilitate the design analysis, enabling the fine-tuning of the device parameters. The findings highlight the effectiveness of perovskite materials in boosting photodetector performance., (© 2025 John Wiley & Sons Ltd.)

Introduction: This study aimed to identify the link between alloy microstructures and the nanomechanical properties of different orthodontic archwires containing nickel-titanium (NiTi) by sensing sliced areas. Previous studies have focused on analyzing and contrasting physical properties such as microhardness, elasticity modulus, and resistance; therefore, the trend is to consider microstructural characteristics in detail., Methods: Thirty archwire samples from 3 different commercial brands, American Orthodontics (AO), 3M Unitek (3M), and Borgatta, were analyzed through scanning electron microscopy and energy-dispersive x-ray spectroscopy, transmission electron microscopy, atomic force microscopy, Berkovich nanoindentation, and microtensile microscopy to determine their chemical-crystallographic characteristics and nanomechanical and bending characteristics., Results: The identified formulations of AO and 3M had averages of 20 wt%, for Ni and 15.4 wt% for Ti, with lower concentrations for Borgatta. Alloys of Ni and Ti were distributed in different concentrates in the matrix of the archwires. The nanomechanical properties showed high values of the elastic modulus (82.8 ± 3.6 GPa) and hardness (6.4 ± 1.2 GPa) and a minor deformation degree of 0.38% for the AO wires, although the bending strength exhibited the highest values for 3M. No corrosion was observed with a prolonged hydrolytic attack on the surface of any of the wires (0.0-0.5 National Bureau of Standards units)., Conclusions: The highest nanomechanical properties and bending characteristics were observed for wires with higher NiTi precipitate contents, which were distributed differently in the alloy overall in the matrix. The nanoindentations sensed in different areas evidenced different mechanical properties for NiTi depending on its concentrations of Ti and enucleations., (Copyright © 2025 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.)

The rGO-based 5% Ni-doped Co 3 O 4 /TiO 2 (GNCT) p-n heterojunction nanocomposite was synthesized using hydrothermal method. The resulting nanocomposite's morphology, structure, surface area, elemental composition, electrical and optical properties were thoroughly examined using a variety of techniques. The GNCT nanomaterial achieved an impressive 99.11% degradation within 40 min, while GPCT closely followed with a 96.6% efficiency. Its smart nanomaterial also excels as a n-butanol sensor, with GNCT showing a sensitivity of 91.51%, and GPCT registering 86.51%. This dual-functionality highlights its potential as an advanced material for environmental and sensing applications. Additionally, GNCT exhibited excellent stability across multiple cycles, underscoring its potential for gas sensing and environmental applications. The remarkable performance of GNCT is a result of the synergistic effects of its morphology (nanosheet), surface area (540.215 m 2 /g), band gap (1.93 eV), and photosensitivity (36.92%), which collectively make it an ideal candidate for the photocatalytic and gas sensing applications., Competing Interests: Declarations. Ethical approval: This manuscript does not contain the studies with human participants or animals performed by any of the others. Consent to participate: Not applicable. Consent for publication: I give my consent for publication. Competing interests: The authors declare no competing interests., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

NiTi alloys are an important class of biomaterials with extensive clinical applications such as cardiovascular stents, orthodontic arch-wires, esophageal stents, orthopedic implants and more. However, the long-term implantation of NiTi alloys presents significant challenges due to their susceptibility to wear, corrosion and the excessive release of harmful nickel ions. These factors can severely compromise both the biocompatibility and the overall service life of the implants. To better meet the demands for safety, durability and superior biological performance after implantation, surface modification of NiTi alloys has become a focal point of current research. Based on the fundamental properties of the NiTi alloys and the challenges encountered in their practical applications, this article provides a focused review of recent advances in improving their corrosion resistance, wear resistance, antibacterial properties and biological performance through surface modification and coating techniques. In addition, the paper outlines current research challenges and proposes recommendations for future development directions., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2025 Elsevier B.V. All rights reserved.)

The purpose of this study was to develop a new instrument to measure the mechanical properties of rotary endodontic Ni-Ti files (ProTaper Gold F2, ProTaper Ultimate F2, and HyFlex EDM Onefile), and to evaluate the overall utility of the device. The instrument was capable of analyzing the 6-axis force/torque generated by the files during cyclic dynamic movement in a metal curved artificial root canal, and doing automatic cyclic dynamic filing in a resin root canal with a preset vertical force limit by adopting a negative feedback mechanism. By analyzing the 6-axis force/torque, we were able to estimate the position and contact points of the files in the curved root canal. ProTaper Gold showed the highest force/torque in all directions. HyFlex EDM had the highest hysteresis ratio, centering ratio value and NCF (number of cycles to fatigue fracture), while the lowest vertical force.

Despite major instrumental developments over the last decade, endodontic files are still not infallible. It is well known that NiTi rotary files can break without any visible sign of deformation. Instrument breakage under combined flexion-torsion loading is still common in clinical practice. Unfortunately, breakage of this type of instrument mainly occurs in narrow canals, through pinching in the apical region. When such an incident occurs, the endodontist must adopt a debris retrieval strategy that is both stressful and not guaranteed success. This study proposes a new method for experimental damage detection leading to the fracture of Ni-Ti shape memory alloy endodontic files. It is based on the acoustic emission (AE) technique and mechanical parameters measured in real-time and image analysis. It has been shown that the AE results correlate with the damage observations and torque and force measurements recorded during the tests. Having carried out numerous root canal treatment on resin blocks, it appears that this new detection and analysis technique can be used to analyze and anticipate the first signs of damage leading to endodontic file failure. The technological development of such a method, at the level of the engine itself, associated with the act in service procedure, would constitute a revolution in the field of endodontics., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Jeanne Davril reports equipment, drugs, or supplies was provided by Micro-Mega SA. Marin Vincent has patent #FR3127686 issued to Marin Vincent. If there are other authors, they declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

A photocurrent enhancing photoelectrochemical (PEC) immunosensor was developed for chloramphenicol (CAP) detection based on cation exchange reaction. The efficient split-type PEC immunosensor combined with controlled-release strategy was established using the ZnIn 2 S 4 /TiO 2 /Ti 3 C 2 MXene (ZIS/T/M) composite as the photoactive material and CuO as the signal response probe. In the presence of target CAP, CuO-labeled CAP antibody (CuO-mAb) was introduced onto the microplate via a competitive-type immunoassay. Under acidic conditions, a large amount of Cu 2+ released from CuO-mAb, which triggered a cation exchange reaction with the Zn 2+ in ZIS/T/M-modified photoelectrode to generate Cu x S, resulting in enhancing the photocurrent. As a result, the quantitative detection of CAP was achieved by detecting the photocurrent change. Under optimized conditions, the linear range of the sensor was 1 pg/mL to 50 ng/mL, and the detection limit was 0.24 pg/mL. The excellent PEC behavior of ZIS/T/M composite could be attributed to the fact that heterojunction formation improved the migration and separation of the photocarrier. Additionally, by virtue of the photocurrent-enhancing strategy via cation exchange reaction and the controlled releasing signal amplification method of ion, the PEC immunosensor has high sensitivity and satisfactory accuracy, offering great potential applications in the determination of CAP., Competing Interests: Declarations. Ethical approval: This research did not involve human or animal samples. Conflict of interest: The authors declare no competing interests., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Austria, part of Springer Nature.)

Devising of materials that afforded dual applicability in decontamination and pollutant detection were still a towering challenge owing to the increasing flux of discharge toxic contaminants over the years. Herein, the NiFe 2 O 4 nanoparticles-loaded on cube-like SrTiO 3 (NiFe 2 O 4 /SrTiO 3 ) composite was fabricated by a two-step hydrothermal approach providing remarkable photocatalytic treatment and electrochemical sensing of noxious pollutants in wastewater. The material traits of the fabricated composite were scrutinized by myriad characterization approaches. The NiFe 2 O 4 /SrTiO 3 hybrid material demonstrated high surface area of 19.81 m 2 /g, adequate band gap energy of 2.75 eV, and prominent photoluminescence characteristics. In the presence of visible light, the NiFe 2 O 4 /SrTiO 3 exhibited profound photocatalysis capability to eliminate sewage effluent-bearing chlortetracycline hydrochloride (CTCH) with 88.6% COD removal in 120 min, outperforming other pure materials. Meanwhile, the toxicity examination of effluent, the possible degradation pathway of CTCH and the proposed photocatalysis mechanism were also divulged. More importantly, the glassy carbon electrode was modified with synergized NiFe 2 O 4 /SrTiO 3 (NiFe 2 O 4 /SrTiO 3 -GCE) was adopted for the precise quantification of Hydrazine (Hz). The NiFe 2 O 4 /SrTiO 3 -GCE obeyed first-order response for the Hz detection within the range of 1-10 mM: cyclic voltametric: limit of detection (LOD) of 0.119 μM with sensitivity of 18.9 μA μM -1 cm -2 , and linear sweep voltametric: LOD of 0.222 μM with a sensitivity of 12.05 μA μM -1 cm -2 . The stability and interference of modified electrode were also inspected. This work furnished valuable insights to yield a composite with the prominent S-scheme heterojunction system for quenching of charge carrier recombination and consequently contributing to the future realization into the domains of environmental clean-up and toxic chemical detection., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Inc. All rights reserved.)

For the sustainable advancement of industrial expansion that is environmentally conscious, harmful dyes must be removed from wastewater. Untreated effluents containing colors have the potential to harm the ecosystem and pose major health risks to people, animals, and aquatic life. Here, we have fabricated Ni or Fe modified with BaTiO 3 materials and effectively utilized them for Reactive Red 120 (RR 120) dye degradation under UV-A light. The synthesized materials were characterized, and their structural, and photo-physical properties were reported. Phase segregation was not present in the XRD pattern, as evidenced by the absence of secondary phase peaks linked to iron, nickel, or oxides. Low metal ion concentrations may be the cause of this, and the presence of those elements was confirmed by XPS measurements. The Raman spectra of the BaTiO 3 /Ni and BaTiO 3 /Fe samples show a widened peak at 500 cm -1 , which suggests that Ni or Fe are efficiently loaded onto the BaTiO 3 . RR 120 dye photodegradation under UV light conditions was effectively catalyzed by BaTiO 3 /Fe, as evidenced by its superior performance in the UV irradiation technique over both BaTiO 3 and BaTiO 3 /Ni. Compared to bare BaTiO 3 , both metal-modified materials efficiently degraded the RR 120 dye. Acidic pH facilitated the degradation process, which makes sense given that the heterogeneous photo-Fenton reaction was the mechanism of degradation along with BaTiO 3 sensitization. High-acidity sewage can be dangerous and carcinogenic, and conventional biological treatment methods are not appropriate for managing it. In the current investigation, it may be used to treat color effluents with extremely low pH levels. Additionally, the ability of the produced nanocomposites to inhibit the growth of twenty pathogens was examined, along with two fungi, fifteen Gram-negative Bacilli (GNB), one Gram-positive Bacilli (GPB), and two Gram-positive Cocci (GBC)., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

Porous nickel-titanium (NiTi) manufactured using metal injection molding (MIM) has emerged as an innovative generation of drug-loaded stent materials. However, an increase in NiTi porosity may compromise its mechanical properties and cytocompatibility. This study aims to explore the potential of porous NiTi as a vascular drug delivery material and evaluate the impact of porosity on its drug loading and release, mechanical properties, and cytocompatibility. MIM, combined with the powder space-holder method, was used to fabricate porous NiTi alloys with three porosity levels. The mechanical properties of porous NiTi were assessed, as well as the surface cell growth capability. Furthermore, by loading rapamycin nanoparticles onto the surface and within the pores of porous NiTi, we evaluated the in vitro drug release behavior, inhibitory effect on cell proliferation, and inhibition of neointimal hyperplasia in vivo. The results demonstrated that an increase in porosity led to a decrease in the mechanical properties of porous NiTi, including hardness, tensile strength, and elastic modulus, and a decrease in the surface cell growth capability, affecting both cell proliferation and morphology. Concurrently, the loading capacity and release duration of rapamycin were extended with increasing porosity, resulting in enhanced inhibitory effects on cell proliferation in vitro and inhibition of neointimal hyperplasia in vivo. In conclusion, porous NiTi holds promise as a desirable vascular drug delivery material, but a balanced consideration of the influence of porosity on both mechanical properties and cytocompatibility is necessary to achieve an optimal balance among drug-loading and release performance, mechanical properties, and cytocompatibility., (© 2024. The Author(s) under exclusive licence to Biomedical Engineering Society.)

Introduction: This study aimed to compare a new multicolored rotary system with four heat-treated rotary instruments using the multimethod approach., Methods: Three-hundred instruments of RCS Rainbow, Rotate, RaCe EVO, OneCurve, and ProTaper Ultimate systems were evaluated regarding their design (stereomicroscopy, scanning electron microscopy, and 3D surface scanning), metallurgy, and mechanical performance (cyclic fatigue, torsional resistance, bending and buckling resistance, and cutting ability). Unprepared surfaces after canal preparation of maxillary molars were evaluated using micro-computed tomography. Kruskal-Wallis and one-way analysis of variance post hoc Tukey tests were used for statistical comparisons (α = 5%)., Results: Instruments exhibited variations in active blade length, number of spirals, and cross-sectional designs. RCS Rainbow showed specific phase transformation temperatures, highest bending (400.5gf) and buckling (286gf) resistance values, and lowest mean angle of rotation (529°) (P < .05). OneCurve exhibited superior cutting ability (8.4 mm) and longer time to fracture (112s). RaCe EVO displayed the lowest time to fracture (51s), maximum torque (1.2 N.cm), buckling (174gf), and bending resistance (261gf) values (P < .05). ProTaper Ultimate showed the highest torque (1.6 N.cm) and angle of rotation (611°) (P < .05), while its bending load (262gf) was comparable to RaCe EVO (P > .05). Rotate instrument showed intermediate values in the mechanical tests. No difference was observed regarding the unprepared canal surfaces (P > .05) CONCLUSIONS: RCS Rainbow demonstrates a trade-off between flexibility and other mechanical properties. Its dimensions exceeded those of other instruments, affording it higher torque resistance, yet concurrently reducing its flexibility, angle of rotation, and cutting ability. OneCurve stands out as a well-balanced choice by integrating geometric design and mechanical performance., (Copyright © 2024 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.)

Background: Manually bent, standard-of-care, Ti-6Al-4V, mandibular graft fixation devices are associated with a significant post-operative failure rate. These failures require the patient to endure stressful and expensive re-operation. The approach recommended in this report demonstrates the optimization of graft fixation device mechanical properties via "stiffness-matching" by varying the fixation device's location, shape, and material composition through simulation of the device's post-operative performance. This provides information during pre-operative planning that may avoid future device failure. Optimized performance may combine translation of all loading into compression of the bone graft with the adjacent bone segments and elimination or minimization of post-healing interruption of normal stress-strain (loading) trajectories., Results: This study reports a sheep mandibular graft model where four animals received virtually optimized, experimental nickel-titanium (NiTi) fixation plates fabricated using laser beam powder bed fusion (LPBF) additive manufacturing (AM). The last animal, our control, received a standard-of-care, manually bent, Ti-6Al-4V (aka Ti64) fixation plate. A 17.5-mm mandibular graft healed completely in all four animals receiving the experimental device. Experimental NiTi-implanted sheep experienced mandibular bone healing and restoration. The Ti64 plate, in the control animal, fractured and dislocated shortly after being implanted., Conclusion: The use of stiffness-matched implants, by means of plate material (NiTi) and geometry (porosity) enhanced bone healing and promoted better load transfer to the healed bone when compared to the bulk Ti64 found in the fixation plate that the Control animal received. The design technique and screw orientation and depth planning improved throughout the study leading to more rapid healing. The large animal model reported here provides data useful for a follow-on clinical trial., (© 2024. The Author(s).)

Objectives: To evaluate the effect of the universal and rapid autoclave cycles on the mechanical properties and surface roughness of nickel-titanium archwires following clinical use., Material and Methods: Thirty-six NiTi archwires (0.016 × 0.022 inch) were equally divided into a control group (Group A) and 2 experimental groups (Group B & C). Wires in group A were tested in the "as-received" form. Wires in the two other groups were installed in patients mouth for 4 weeks, and then autoclaved using the rapid-cycle (Group B) or the universal-cycle (Group C). All wires were subjected to 3-point bending test to calculate the elastic limit, modulus of elasticity, spring-back, yield strength, resilience and toughness. Atomic force microscopy (AFM) was used for surface roughness qualitative and quantitative analysis., Results: Group B showed significantly higher values of elastic limit, modulus of elasticity, resilience, yield strength and toughness than the other two groups. No significant differences were detected between groups A and C (P > 0.05). Group B showed significantly lower average surface roughness than the other two groups, but no significant differences were detected between groups A and C (P > 0.05)., Conclusions: The mechanical properties and surface roughness of clinically used NiTi wires were less affected by the universal-cycle than the rapid-cycle autoclaving. However, the difference between the effect of both autoclave cycles was diminutive., Clinical Relevance: The mechanical properties and surface roughness of the tested NiTi wires were not notably altered by clinical use and autoclaving., (© 2024. The Author(s).)

An extracellular matrix protein, fibronectin (Fn), was covalently immobilized on 316L stainless steel, L605 cobalt chromium (CoCr), and nickel titanium (NiTi) surfaces through an 11-mercaptoundecanoic acid (MUA) self-assembled monolayer (SAM) pre-formed on these surfaces. Polarization modulation infrared reflection adsorption spectroscopy (PM-IRRAS) confirmed the presence of Fn on the surfaces. The Fn monolayer attached to the SAM was found to be stable under fluid shear stress. Deconvolution of the Fn amide I band indicated that the secondary structure of Fn changes significantly upon immobilization to the SAM-functionalized metal substrate. Scanning electron microscopy and energy dispersive X-ray analysis revealed that the spacing between Fn molecules on a modified commercial stent surface is approximately 66 nm, which has been reported to be the most appropriate spacing for cell/surface interactions.

This study aimed to evaluate surface defects of Remover rotary Nickel-Titanium (NiTi) files after single and multiple uses in conventional endodontic retreatment procedures using scanning electron microscopy (SEM). Eighty acrylic blocks, simulating root canals with a 1.5 mm internal diameter, a 5 mm radius of curvature, and a 55° curvature, were utilized. After chemomechanical preparation and obturation, 24 new Remover files (N30, 7%, L23) were randomly assigned to three groups: single use, triple use, and six uses. The files were operated at 600 rpm with a torque of 2.5 Ncm, cleaned, and sterilized after each use. SEM analysis at magnifications of 100x, 250x, and 500x revealed surface defects, including tip deformation, microcracks, fracture, unwinding, surface pitting, and blade disruption. Deformation was observed in 75% of the files after a single use and in 100% of the files after three and six uses. Microcracks were absent after single use but appeared in 25% and 87.5% of files after three and six uses, respectively, showing a statistically significant increase (p < 0.001). Surface pitting also significantly increased among groups (p = 0.004). No fractures were observed in any group. The most common defects were tip deformation (91.7%) and surface pitting (70.8%). The findings suggest that repeated use of NiTi files significantly increases surface defects, elevating the risk of fatigue fractures. Thus, the results recommend limiting the reuse of Remover files to a maximum of 3x. Further research is needed to correlate defect types with anatomical factors and to assess file effectiveness in retreatment scenarios.

Objective: This study evaluated the force system generated by the Memory Titanol® spring (MTS) with different preactivation bends using an orthodontic force tester (OFT)., Methods: Three preactivations were tested using a 0.017 × 0.022-in stainless steel (SS) wire and a 0.018 × 0.025-in NiTi segment, with an activation of 30º in the posterior segment (β), with 0º (Group 1 [G1]), 45º (Group 2 [G2]), and 60º (Group 3 [G3]) in the anterior segment (α)., Results: The molars showed extrusion values of -1.33 N for G1 and -0.78 N for G2, and an intrusion value of 0.33 N for G3. The force in the premolars was intrusive with a variation of 1.34 N for G1 and 0.77 N for G2; and extrusive with a variation of -0.31 N for G3. Regarding the upright moment (Ty) of the molar, a distal moment was observed with values of 53.45 N.mm for G1 and 19.87 N.mm for G2, while G3 presented a mesial moment of -6.23 N.mm. G1, G2, and G3 all exhibited distal premolar moments (Ty) of 3.58, 2.45, and 0.68 N.mm, respectively., Conclusions: The tested preactivations exerted an extrusive force in G1 and G2 and an intrusive force in G3 during molar vertical movement. The premolar region in G1 and G2 showed intrusive force and distal moment.

The remarkable mechanical properties of nickel-titanium (NiTi) shape memory alloy, particularly its super-elasticity, establish it as the material of choice for fabricating self-expanding vascular stents, including the metallic backbone of peripheral stents and the metallic frame of stent-grafts. The super-elastic nature of NiTi substantially influences the mechanical performance of vascular stents, thereby affecting their clinical effectiveness and safety. This property shows marked sensitivity to the primary parameters of the heat treatment process used in device fabrication, specifically temperature and processing time. In this context, this study integrates experimental and computational analyses to explore the potential of designing the mechanical characteristics of NiTi vascular stents by adjusting heat treatment parameters. To reach this aim, differently heat-treated NiTi wire samples were experimentally characterized using calorimetric and uniaxial tensile testing. Subsequently, the mechanical response of a stent-graft model featuring a metallic frame made of NiTi wire was assessed in terms of radial forces generated at various implantation diameters through finite element analysis. The stent-graft served as an illustrative case of NiTi vascular stent to investigate the impact of the heat treatment parameters on its mechanical response. From the study a strong linear relationship emerged between NiTi super-elastic parameters (i.e., austenite finish temperature, martensite elastic modulus, upper plateau stress, lower plateau stress and transformation strain) and heat treatment parameters (R 2  > 0.79, p-value < 0.001) for the adopted ranges of temperature and processing time. Additionally, a strong linear relationship was observed between: (i) the radial force generated by the stent-graft during expansion and the heat treatment parameters (R 2  > 0.82, p-value < 0.001); (ii) the radial force generated by the stent-graft during expansion and the lower plateau stress of NiTi (R 2  > 0.93, p-value < 0.001). In conclusion, the findings of this study suggest that designing and optimizing the mechanical properties of NiTi vascular stents by finely tuning temperature and processing time of the heat treatment process is feasible., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier Ltd.. All rights reserved.)

The exploration of noble metal-free nanoarrays as high-activity catalytic electrodes for glucose biosensing holds great significance. Herein, we propose a Ni nanoparticle-decorated TiO 2 nanoribbon array on a titanium plate (Ni@TiO 2 /TP) as an effective non-enzymatic glucose biosensing electrode. The as-prepared Ni@TiO 2 /TP electrode demonstrates rapid glucose response, a wide linear response range (1 μM to 1 mM), a low detection limit (0.08 μM, S/N = 3), and high sensitivity (10 060 and 3940 μA mM -1 cm -2 ), with good mechanical flexibility and stability. Moreover, it proves efficient in glucose biosensing in real human blood serum and cell culture fluid. Thus, it is highly promising for practical applications.

Objective: Current standardized in vitro bending experiments for orthodontic archwires cannot capture friction conditions and load sequencing during multi-bracket treatment. This means that clinically relevant forces exerted by superelastic wires cannot be predicted. To address these limitations, this study explored a novel test protocol that estimates clinical load range., Methods: The correction of a labially displaced maxillary incisor was simulated using an in vitro model with three lingual brackets. Deflection force levels derived from four different protocols were designed to explore the impact of friction and wire load history. These force levels were compared in nickel-titanium (NiTi) archwires with three commonly used diameters. The unloading path varied between protocols, with single or multiple sequences and different load orders and initial conditions., Results: Deflection forces from the new protocol, employing multiple continuous load/unload cycles (CC incr ), consistently exceeded those from the conventional protocol using a single continuous unloading path (CU decr ). Mean differences in plateau force ranged from 0.54 N (Ø 0.014" wire) to 1.19 N (Ø 0.016" wire). The CC inr protocol also provided average force range estimates of 0.47 N (Ø 0.012" wire), 0.89 N (Ø 0.014" wire), and 1.15 N (Ø 0.016" wire)., Significance: Clinical orientation towards CU decr carries a high risk of excessive therapeutic forces because clinical loading situations caused by friction and load history are underestimated. Physiological tooth mobility using NiTi wires contributes decisively to the therapeutic load situation. Therefore, only short unloading sequences starting from the maximum deflection in the load history, as in CC incr , are clinically meaningful., Competing Interests: Declaration of Competing Interest The authors declare that there are no conflicts of interest regarding the publication of this article. No financial or personal relationships have influenced the outcomes of this work., (Copyright © 2024 The Authors. Published by Elsevier Inc. All rights reserved.)

In order to properly satisfy biomedical constraints for cardiovascular applications, additively manufactured NiTi scaffolds required further process and metallurgical engineering. Additively manufactured NiTi materials for cardiovascular use will have to undergo surface finishing in order to minimize negative surface interactions within the artery. In this study, we sought to understand biocompatibility from chemically etched additively manufactured NiTi scaffolds by laser powder bed fusion (LPBF). Although two distinct oxide films were created in the surface etching process (labeled CP-A and CP-B), no qualitative changes in microroughness were seen between the two conditions. CP-A possessed significantly less Ni at the surface (0.19 at. %) than the CP-B group (3.30 at. %), via x-ray photoelectron spectroscopy, alongside a concomitant shift in the O1 s peak presentation alluding to a greater formation of a Ni based oxide in the CP-B group. Our live dead staining revealed significant toxicity and reduced cellular attachment for the CP-B group, in addition to inducing more cell lysis (20.9 ± 5.1%), which was significantly increased when compared to CP-A (P < 0.01). Future practices of manufacturing NiTi scaffolds using LPBF should focus on producing surface films that are not only smooth, but free of cytotoxic Ni based oxides., (© 2024 Author(s). All article content, except where otherwise noted, is licensed under a Creative Commons Attribution (CC BY) license (https://creativecommons.org/licenses/by/4.0/).)

Background: To investigate the torque expression of conventional stainless steel (SS) brackets in combination with rectangular SS archwires and nickel-titanium (NiTi) V-slot brackets in combination with V-shaped NiTi archwires using finite element analysis (FEA)., Methods: CAD models were created for a conventional bracket and rectangular archwires with dimensions of 0.018″x0.025″ and 0.019″x0.025″, and for a V-slot bracket and V-shaped archwires with heights of 0.55 mm, 0.60 mm and 0.70 mm. FEA was performed using Ansys 2022R2 software to assess the forces and moments during simulated torsion of the archwires in the brackets between 0° and 25° with varying interbracket distances and free path lengths., Results: The V-slot bracket-archwire combination exhibited force transmission and moment generation within 1° of torsion. The transmissible force increased with the torsion angle, but showed an upper limit of about 13-14 Nmm. The SS bracket-archwire combination showed negligible forces and moments for simulated torsion between 0° and 15°. At torsions of 25°, moments of 12 Nmm and 14 Nmm occurred for the 0.018″x0.025″ and 0.019″x0.025″ archwire dimensions, respectively., Conclusions: The V-slot bracket-archwire combination is effective in expressing torque and preventing both over- and under-activation. Conventional bracket-archwire combinations showed torsional losses due to play between 10 and 15°, depending on the dimensions of the respective archwire, and no upper torsional moment limit., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: The author Prof. Dr. Andrea Wichelhaus codeveloped the RED bracket. The RED bracket is manufactured by Redsystem and she is a shareholder of said company. All other authors declare that they have no potential conflicts of interest., (Copyright © 2024 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Aim: This study was twofold: (i) it aimed to investigate the morphometric changes of three temperature-sensitive nickel-titanium (NiTi) instruments at different temperatures, and (ii) to conduct an in vivo real-time analysis of intracanal temperature changes., Methods: Changes in the shape and length of XP-Endo Shaper, XP-Endo Finisher, and XP-Endo Finisher-R were evaluated in real time whilst heated in a temperature-controlled water bath from 22 to 45°C. Instruments were fixed to a laminated water-resistant 1 mm graph paper attached to a stone block. Instruments were imaged whilst subjected to increasing temperature using a digital camera attached to an operating microscope. From recorded videos, still frames were extracted at 10-s intervals and changes in the length and shape of each instrument were measured and changes were plotted against time. Moreover, the intracanal temperature of distal roots of lower molars was measured in vivo for patients attending the clinic for non-surgical root canal treatments. The temperature was measured using a K-type thermocouple probe inserted into the mid-root level after irrigating the canal with a solution set at room temperature (22°C) or heated to 45°C. The intraoral and intracanal temperatures were recorded using a video camera for 180 s at 5-s intervals to plot the change in the intraoral and intracanal temperature, after both irrigation solution temperatures, with time., Results: The shape transformation of XP-Endo Shaper began at 31.5 ± 2.0°C and reached its optimal transformation at 35.1 ± 1.0°C. For the Finisher and Finisher-R, shape transformations began at 29.2 ± 1.9 and 26.9 ± 2.2°C reaching the optimal transformation at 33.9 ± 1.4 and 32.7 ± 1.7°C, respectively. The average decreases in lengths of XP-Endo Shaper, Finisher, and Finisher-R after full transformation were 0.43 ± 0.23, 1.07 ± 0.22, and 1.15 ± 0.22 mm, respectively. The intracanal temperature reached 32.9 ± 0.8 and 33.2 ± 1.0°C after 3 min of application of irrigation solutions set at 22 or 45°C, respectively., Conclusion: The tested instruments exhibited diverse changes in their shapes and lengths at varying temperatures. Despite the temperature of the irrigation solution, the intracanal temperature consistently remained lower than the intracanal temperature once equilibrium was reached. This highlights the importance of considering the temperature of irrigation solution during in vitro testing of endodontic instruments., (© 2024 British Endodontic Society. Published by John Wiley & Sons Ltd.)

Nickel-titanium (NiTi) instruments offer many advantages during endodontic instrumentation; however, the fracture risk within the canal remains a concern. Manufacturers continuously develop and introduce instruments to the market with supposedly enhanced cyclic fatigue resistance and increased flexibility, achieved through different proprietary manufacturing processes, the details of which have not been made public. In recent years, two rotary systems specially designed for deciduous teeth have been commercially available, but information about their performance is lacking. This investigation aimed to identify which manufacturing process provides better cyclic fatigue resistance: the AF-H Wire technology used in the AF baby rotary files (AF-f) or the CM-Wire technology used in the i3 Gold deciduous teeth rotary files (i3G-f). Forty rotary International Organization for Standardization (ISO) 25/04 files were tested in artificial canals with a standard geometry of 60° angle and 2.5 mm radius until fracture. The number of cycles to fracture was calculated, and the length of the fragments was measured. A scanning electron microscope (SEM) was used to examine the fracture surfaces and fragments. Energy dispersive spectroscopy (EDS) was used to determine the percentage weight of NiTi in each file. The statistical analysis (Mann-Whitney test) showed that the cyclic fatigue resistance of the AF-f was significantly higher ( p < 0.0001) than that of the i3G-f. Additionally, there was a significant difference ( p = 0.0419) in the length of the fractured fragments. All instruments showed one or more types of manufacturing defects and presented similar NiTi percentages by weight. The manufacturing process is critical to cyclic fatigue resistance, and there seems to be responsible for the difference in cyclic fatigue resistance between these similar instruments., Competing Interests: The authors declare no conflict of interest., (©2024 The Author(s). Published by MRE Press.)

Nickel-titanium (NiTi) rotary files used in root canal treatments experience fatigue and shear damage due to the complex curved geometries and operating conditions encountered within the root canal. This can lead to premature file fracture, causing severe complications. A comprehensive understanding of how different factors contribute to file damage is crucial for improving their functional life. This study investigates the combined effects of root canal curvature radius, file canal curvature, and rotational speed on the fatigue life and failure modes of NiTi endodontic files through an integrated computational and experimental approach. Advanced finite element simulations precisely replicating the dynamic motion of files inside curved canal geometries were conducted. Critical stress/strain values were extracted and incorporated into empirical fatigue models to predict the functional life of endodontic files. Extensive experiments with files rotated inside artificial curved canals at various canal curvatures and speeds provided validation. Increasing the canal curvature beyond 60 ∘ and shorter curvature radii below 5 mm dramatically reduced the functional life of the endodontic file, especially at rotational speeds over 360 rpm. The Coffin-Manson fatigue model based on strain amplitude showed the closest agreement with experiments. Shear stresses dominated damage at low canal curvatures, while the combined shear-fatigue loading effects were prominent at higher canal curvatures. This conclusive study elucidates how operational parameters like canal curvature radii, canal curvature, and rotational speed synergistically influence the fatigue damage processes in NiTi files. The findings offer valuable guidelines to optimize these factors, significantly extending the functional life of endodontic files and reducing the risk of intra-operative failures. The validated computational approach provides a powerful tool for virtual testing and estimation of the functional life of the new file designs before manufacturing., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Sahil Kalra has patent Scotch Yoke Mechanism Based Cyclic Fatigue Testing Device for Rotary Endodontic Files pending to 202311042833. If there are other authors, they declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

This study explores the synthesis, characterization, and photocatalytic performance of a SnO 2 /TiO 2 -Ni@rGO nanocomposite for tetracycline (TC) degradation under visible light irradiation. The nanocomposite was precisely designed to enhance structural stability, charge transfer efficiency, and catalytic activity. X-ray diffraction (XRD) analysis confirmed the structural integrity of the SnO 2 /TiO 2 -Ni@rGO composite, demonstrating excellent reusability and resistance to photo-corrosion after multiple cycles. Photocatalytic experiments revealed that the SnO 2 /TiO 2 -Ni@rGO nanocomposite significantly outperformed individual SnO 2 /TiO 2 -Ni and rGO catalysts, achieving a remarkable 94.6% degradation of TC within 60 min. The degradation process followed pseudo-first-order kinetics, with a rate constant (k) of 0.046 min -1 . The Z-scheme charge transfer mechanism facilitated efficient separation and migration of photogenerated charge carriers, generating reactive oxygen species such as superoxide (•O 2 - ) and hydroxyl (•OH) radicals crucial for the oxidation of TC. Radical scavenger studies confirmed that superoxide and hydroxyl radicals were the primary active species. The SnO 2 /TiO 2 -Ni@rGO composite also exhibited excellent reusability, maintaining high catalytic performance over four consecutive cycles. These findings suggest that the SnO 2 /TiO 2 -Ni@rGO nanocomposite is a promising candidate for the efficient and sustainable photocatalytic degradation of persistent organic pollutants like TC, offering significant potential for environmental remediation applications., (© 2024 John Wiley & Sons Ltd.)

This study investigated phytic acid (IP6) effect on chemical, structural, and mechanical characteristics of nickel-titanium (NiTi) files. The tested files were equally divided into groups according to the immersion protocol: sodium hypochlorite (NaOCl), ethylenediaminetetraacetic acid (EDTA), IP6, EDTA followed by NaOCl, and IP6 followed by NaOCl. These groups were then compared in terms of Ni, Ti, and chromium (Cr) ions release from the files. Microstructural changes using field emission scanning electron microscope (Fe-SEM) and energy dispersive X-ray spectroscopy (EDX) and surface roughness were analyzed. The mechanical characterization was conducted using cyclic fatigue resistance test. Fractured segments were scanned under SEM. Statistical analysis was performed using one-way ANOVA, Tukey test, Kruskal-Wallis test and Mann-Whitney U test. Results showed that NaOCl caused significant release of Cr, followed by IP6 and EDTA (P < 0.05). When files were pre-immersed in EDTA, NaOCl tended to induce less release of Ti and Cr. EDX evaluation revealed that the main surface elements were Ni, Ti, carbon, and oxygen. EDTA group contained the highest amount of carbon, while the control group showed the lowest. Surface roughness evaluation revealed no significant differences between groups despite the minor increases after immersion in certain groups. Black areas were observed in the NaOCl group which indicated corrosion. However, the cyclic fatigue test showed no significant differences between the groups., (© 2024. The Author(s).)

Background: The screw-in effect is a tendency of a nickel-titanium (NiTi) rotary endodontic file to be pulled into the canal, which can result in a sudden increase in stress leading to instrument fracture, and over-instrumentation beyond the apex. To reduce screw-in force, repeated up-and-down movements are recommended to distribute flexural stress during instrumentation, especially in curved and constricted canals. However, there is no consensus on the optimal number of repetitions. Therefore, this study aimed to examine how repeated up-and-down movements at the working length affect torque/force generation, surface defects, and canal shaping ability of JIZAI and TruNatomy instruments., Methods: An original automated root canal instrumentation device was used to prepare canals and to record torque/force changes. The mesial roots of human mandibular molars with approximately 30˚ of canal curvature were selected through geometric matching using micro-computed tomography. The samples were divided into three groups according to the number of up-and-down movements at the working length (1, 3, and 6 times; n = 24 each) and subdivided according to the instruments: JIZAI (#13/0.04 taper, #25/0.04 taper, and #35/0.04 taper) or TruNatomy (#17/0.02 taper, #26/0.04 taper, and #36/0.03 tape) (n = 12 each). The design, surface defects, phase transformation temperatures, nickel-titanium ratios, torque, force, shaping ability, and surface deformation were evaluated. Data were analyzed with the Kruskal-Wallis and Dunn's tests (α = 0.05)., Results: The instruments had different designs and phase transformation temperatures. The 3 and 6 up-and-down movements resulted in a smaller upward force compared to 1 movement (p < 0.05). TruNatomy generated significantly less maximum torque, force, and surface wear than JIZAI (p < 0.05). However, TruNatomy exhibited a larger canal deviation (p < 0.05). No statistical differences in shaping ability were detected between different up-and-down movements., Conclusions: Under laboratory conditions with JIZAI and TruNatomy, a single up-and-down movement at the working length increased the screw-in force of subsequent instruments in severely curved canals in the single-length instrumentation technique. A single up-and-down movement generated more surface defects on the file when using JIZAI. TruNatomy resulted in less stress generation during instrumentation, while JIZAI better maintained the curvature of root canals., (© 2024. The Author(s).)

Because nickel-titanium (NiTi) alloys have unique functions, such as superelasticity, shape memory, and hysteresis similar to bone in the loading-unloading cycles of their recoverable deformations. They likely offer good bone integration, a low loosening rate, individual customization, and ease of insertion. Due to the poor processability of NITI, traditional methods cannot manufacture NiTi products with complex shapes. Orthopedic NiTi implants need to show an adequate fracture elongation of at least 8%. Additive manufacturing can be used to prepare NiTi implants with complex structures and tunable porosity. However, as previously reported, additively manufactured NiTi alloys could only exhibit a maximum tensile fracture strain of 7%. In new reports, a selective laser melting (SLM)-NiTi alloy has shown greater tensile strain (15.6%). Nevertheless, due to the unique microstructure of additive manufacturing NiTi that differs from traditional NITI, the biocompatibility of SLM-NITI manufactured by this new process requires further evaluation In this study, the effects of the improved NiTi alloy on bone marrow mesenchymal stem cell (BMSC) proliferation, adhesion, and cell viability were investigated via in vitro studies. A commercial Ti-6Al-4V alloy was studied side-by-side for comparison. Like the Ti-6Al-4V alloy, the SLM-NiTi alloy exhibited low cytotoxicity toward BMSCs and similar effect on cell adhesion or cell viability. This study demonstrates that the new SLM-NiTi alloy, which has exhibited improved mechanical properties, also displays excellent biocompatibility. Therefore, this alloy may be a superior implant material in biomedical implantation., (© 2024. The Author(s).)

This study assessed the ability of Twisted File Adaptive (TFA), TruNatomy (TRN) and VDW.Rotate (VR) instruments activated by continuous rotation (CR) and adaptive motion (AM) to shape curved root canals. Thirty mandibular molars with two separate mesial canals 20°-40° curved were collected and scanned using micro-computed tomography (μCT). The canals were then randomly assigned into six groups (n = 10): TRN, VR or TFA instruments activated by CR or AM. TRN groups 17.02, 20.04 and 26.04; VR groups 15.04, 20.05 and 25.06; TFA groups were shaped consecutively using 15K-file, 20.04 and 25.06. After they were shaped, the canals were scanned again. The volume of removed dentin, canal transportation and centring ratio were calculated μCT images. All data were analysed using the Kruskal-Wallis test or one-way analysis of variance (p < 0.05). With both kinematics, the TRN instrument removed the least amount of dentin, the VR-CR and the TFA-AM removed the most (p < 0.05). The transportation and centring ratios among all groups were similar (p > 0.05). The volume of dentin removed, the diameter or design features of the instruments and different kinematics did not affect the centring ratio and the amount of transportation and remained within safe limits. All three instruments activated by either kinematics were found to have similar effectiveness in shaping curved root canals., (© 2024 Australian Society of Endodontology Inc.)

Introduction: Nickel-titanium rotary endodontic files have been commercially available for decades, but more recent innovations have introduced heat-treated and surface-treated files. This study investigated the corrosion properties of various nickel-titanium files in normal saline and sodium hypochlorite (NaOCl)., Methods: Ten different file brands of size 40 with a 0.04 taper were subjected to electrochemical testing in 0.9% NaCl (saline) and 5.25% NaOCl at room temperature. The Open Circuit Potential (OCP) was observed for 1 hour followed by a cyclic polarization test from -300 to 700 mV and back to -300 mV (vs OCP). Nonparametric ANOVA and a pairwise comparison (P < .05) were used for statistical analysis of the OCP at 1 hour and the corrosion current (Icorr) obtained via the cyclic polarization test., Results: Significant differences (P < .05) were found between files with respect to OCP and Icorr in both solutions. Nine files exhibited significantly greater (P < .05) Icorrs in NaOCl than in saline. Conversely, pitting corrosion was observed in the saline solution but not NaOCl. Weak and/or moderate correlations existed between OCP and Icorr measures in the 2 solutions., Conclusion: Significant differences in electrochemical properties were observed among the 10 brands of files. Overall, there was not a clear trend between conventional, heat-treated, or surface-treated files among OCP or Icorr in either solution., (Copyright © 2024 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.)

Introduction: In an effort to enhance the quality of mechanized endodontic instruments, various thermal treatment methods, and design modifications have been suggested. However, upon evaluation, these endodontic instruments may exhibit microscopic irregularities. The objective of this in vitro study was to analyze the cutting capacity, surface finish, and mechanical properties of Nickel-Titanium 25/.04 Rotate (VDW GmbH, Munich, Germany) and LOGIC 2 (Easy Equipamentos Odontológicos, Belo Horizonte, MG, Brazil) rotary instruments., Methodology: Twenty rotary instruments were divided into 2 groups: GR, the group with ROTATE instruments (n = 10); and GL2, the group with LOGIC 2 instruments (n = 10). They were evaluated for roughness, using a profilometer, for bending resistance, buckling resistance, and cutting capacity using a universal testing machine, as well as for torsional strength (torque and angular deflection) using a torquemeter. The instruments were visualized before and after the mechanical tests through scanning electron microscopy., Results: GR showed better surface finish in terms of roughness, greater cutting capacity, and greater angular deflection than GL2 (P < .05). However, GL2 showed better flexibility than GR (P < .05). GL2 and GR did not show statistically significant differences in terms of buckling and torque (P > .05)., Conclusion: The ROTATE and LOGIC 2 rotary instruments differed in their surface finish, cutting capacity, and mechanical properties, except for their buckling resistance and required fracture torque., (Copyright © 2024 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.)

Aim and Objective: To evaluate and compare the impact of nanocoatings made of oxides of Aluminum, Titanium, and Zirconium, on the frictional resistance on three types of superelastic orthodontics archwires namely; nickel titanium, copper nickel titanium and low hysteresis nickel titanium., Materials and Methods: There are120 archwire segments of equal dimensions were divided into four groups ( n = 30) with 10 samples each of low hysteresis superelastic archwires; NiTi archwires and CuNiTi archwires. While group A were uncoated, other groups were nanocoated with group B: Aluminum oxide; group C: Titanium dioxide; group D: Zirconium oxide respectively. Upper premolar metal brackets MBT 0.022 slot were used for testing. The frictional properties of the archwires were measured using a Universal testing machine equipped with a custom-made jig. Statistical tests including analysis of variance and post hoc tests were used for analysis., Results: The least frictional resistance among the three types of archwires was seen with low hysteresis(L&H) NiTi wires coated with ZrO 2 (3.1253 ± 0.45822 N ) and the highest with uncoated CuNiTi archwires (7.1113 ± 1.29031 N ). Among the nanocoatings, the least value was found for ZrO 2 nanocoatings followed by TiO 2 , Al2O 3 and highest with uncoated archwires across all three types of archwires., Conclusion: Low hysteresisNiTi have the least frictional resistance compared to CuNiTi and NiTi archwires. The findings also suggest that all the three metal oxide nanocoatings reduce frictional resistance significantly, among which, ZrO 2 nanocoatings were the most effective. This study underscores the potential efficacy of metal oxide nanocoatings in reducing archwire friction and, consequently, will improve orthodontic treatment efficiency and patient comfort. How to cite this article: Dilip S, Rajkumar K. The Effect of Three Metal Oxide Nanocoatings on the Frictional Resistance of Superelastic Orthodontic Archwires: A Comprehensive In vitro Analysis. J Contemp Dent Pract 2024;25(7):649-655.

Purpose: To evaluate the stress distribution along a premolar's root dentin, its post, and its post-luting agent when materials with different elastic moduli are used to fabricate one-piece post-and-cores in two different designs., Materials and Methods: Two 3D virtual models (for cylindrical and conical post designs) of a mandibular premolar restored with one-piece post-and-core restorations were obtained using a software. A total of eight post-and-core materials were tested: polyetheretherketone (PEEK), polyetherketoneketone (PEKK), glass fiber-reinforced polyetheretherketone (GFR-PEEK), carbon fiber-reinforced polyetheretherketone (CFR-PEEK), gold-palladium alloy (Au-Pd), titanium (Ti), zirconia (Zi), and chromium-nickel (Cr-Ni). Maximum principals stress (MPS) in the post, post-luting agent, and root dentin were determined. A load of 150 N was applied to the buccal cusp in the linguo-labial direction at an angle of 45 degrees oblique to the longitudinal axis of the crown., Results: The highest MPS value in post structure was observed with Cr-Ni material for both post designs. Similarly, the highest MPS value in the post-luting agent was observed for Cr-Ni, the material with the highest elastic modulus. However, in the root dentin, the highest value was observed in PEEK, the material with the lowest elastic modulus., Conclusions: Post material and design influenced the stress concentration in the post, post-luting agent, and root dentin. The stress at the root dentin was slightly higher for polymeric materials. Cylindrical post design revealed lower stresses than conical post design at root dentin for all post-and-core materials tested.

The aim of this study was to evaluate how preset torque settings influence the torque, vertical force, and root canal-centering ability of ProGlider and ProTaper NEXT nickel-titanium rotary instruments in canals with different curvature locations. Based on micro-computed tomography, mesial roots of human mandibular molars (25°-40° curvature) were allocated to the apical curvature (apical 1-5 mm) or the middle curvature (apical 5-9 mm) groups, and mandibular incisors (curvature <5°) to the straight canal group. Each group was subjected to automated instrumentation and torque/force measurement with the preset torque of 1, 2.5, or 5 N•cm. Canal-centering ratios were determined with micro-computed tomography. Instrument fracture occurred only in the 2.5 and 5 N•cm groups in curved canals. The preset torque setting and curvature location did not influence canal shaping ability.

Purpose: Altered hemodynamics caused by the presence of an endovascular device may undermine the success of peripheral stenting procedures. Flow-enhanced stent designs are under investigation to recover physiological blood flow patterns in the treated artery and reduce long-term complications. However, flow-enhanced designs require the development of customised manufacturing processes that consider the complex behaviour of Nickel-Titanium (Ni-Ti). While the manufacturing routes of traditional self-expanding Ni-Ti stents are well-established, the process to introduce alternative stent designs is rarely reported in the literature, with much of this information (especially related to shape-setting step) being commercially sensitive and not reaching the public domain, as yet., Methods: A reliable manufacturing method was developed and improved to induce a helical ridge onto laser-cut and wire-braided Nickel-Titanium self-expanding stents. The process consisted of fastening the stent into a custom-built fixture that provided the helical shape, which was followed by a shape-setting in air furnace and rapid quenching in cold water. The parameters employed for the shape-setting in air furnace were thoroughly explored, and their effects assessed in terms of the mechanical performance of the device, material transformation temperatures and surface finishing., Results: Both stents were successfully imparted with a helical ridge and the optimal heat treatment parameters combination was found. The settings of 500 °C/30 min provided mechanical properties comparable with the original design, and transformation temperatures suitable for stenting applications (A f  = 23.5 °C). Microscopy analysis confirmed that the manufacturing process did not alter the surface finishing. Deliverability testing showed the helical device could be loaded onto a catheter delivery system and deployed with full recovery of the expanded helical configuration., Conclusion: This demonstrates the feasibility of an additional heat treatment regime to allow for helical shape-setting of laser-cut and wire-braided devices that may be applied to further designs., (© 2024. The Author(s).)

This study examined the effects of liquid nitrogen vapor on osteogenesis in the rabbit femur. Cryotweezers made of porous nickel titanium alloy (nitinol or NiTi) obtained by self-propagating high temperature synthesis were used in this experiment. The porous structure of the cryotweezers allows them to hold up to 10 g of liquid nitrogen after being immersed for 2 min, which completely evaporates after 160 s. To study the effects of liquid nitrogen evaporation on osteogenesis, a rabbit femur was perforated. The formed holes were subjected to cryotherapy with varying exposure times. It was found that a 3 s exposure time stimulates osteogenesis, which was manifested in a greater number of osteoblasts in the regenerate compared to the control sample without liquid nitrogen. It was observed that increasing the exposure to 6, 9 or 12 s had a destructive effect, to varying degrees. The most severe damage was exerted by a 12 s exposure, which resulted in the formation of osteonecrosis areas. In the samples exposed to 6 and 9 s of cryotherapy, destruction of the cytoplasm of osteocytes and osteoclasts was observed., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Published by Elsevier Inc.)

Purpose: The fatigue resistance of mechanical nickel-titanium files was tested by phase-locked infrared flaw detection method, in order to timely detect instrument wear, providing reference for clinical safe use and timely abandonment of nickel-titanium files., Methods: Twenty sets of mechanical nickel-titanium files were selected from Reciproc-Blue(RB), MTWO and S3 respectively, and resin simulated root canals with 60° and 90° bending were prepared, which were divided into 6 subgroups. The fatigue value after use, the number of uses before breaking and the length of fracture of file 25# of each group of files were recorded and compared with SPSS 26.0 software package., Results: With the increase of the times of use, the fatigue value of the three kinds of files increased gradually. Among the two types of curved root canals, the number of uses before fracture in RB group was significantly increased compared with that in MTWO group and S3 group (P＜0.05). The number of uses of the three kinds of files in the 90° curved root canal were significantly less than in the corresponding groups in the 60° curved root canal(P＜0.05). There was no significant difference in the length of fracture among the three kinds of files(P＞0.05)., Conclusions: Phase-locked infrared flaw detection method can be used for non-destructive testing and quantitative analysis of the fatigue degree of nickel-titanium files.

Objectives: This study aimed to compare the surface roughness and friction of different orthodontic archwires after exposure to salbutamol sulphate inhalation, an anti-asthmatic medication., Methods: Orthodontic archwires (stainless-steel [StSt], nickel-titanium [NiTi], beta-titanium [β-Ti], and copper-NiTi [Cu-NiTi]) were equally divided into two groups. The exposed groups were subjected to 20 mg salbutamol sulphate for 21 days and kept in artificial saliva. The control groups were only kept in artificial saliva. Surface changes were visualized using scanning electron microscopy (SEM). The average surface roughness (Ra) was evaluated using atomic force microscopy (AFM), and friction resistance forces were assessed using a universal testing machine. Statistical analyses were performed using t-tests and ANOVA followed by post hoc tests., Results: Salbutamol sulphate did not change the surface roughness of StSt and NiTi archwires (p > .05). However, the change in the surfaces of β-Ti and Cu-NiTi archwires was significant (p < .001). The frictional forces of exposed StSt, NiTi, and Cu-NiTi archwires did not change (p > .05). However, the frictional forces of β-Ti archwires increased significantly after exposure to salbutamol sulphate (p = .021). Brushing with fluoride after exposure to salbutamol sulphate increased the frictional forces of β-Ti only (p = .002)., Conclusions: Salbutamol sulphate inhalation significantly affected the surface texture of β-Ti and Cu-NiTi orthodontic archwires and increased the friction of β-Ti archwires. These deteriorating effects were not detected on the surface of StSt and NiTi archwires. Therefore, we suggest that β-Ti and copper titanium archwires should be used cautiously in individuals under salbutamol sulphate inhalation treatment., (© 2024 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.)

Recently developed Nickel-Titanium (NiTi) instruments with practical changes have resulted in safer instrumentation. In addition, topographical features on the file surface are a contributing factor to clinical durability. Therefore, this study aimed to investigate both the cyclic fatigue resistance and the roughness change of MTwo and Rotate instruments (VDW, Munich, Germany). Each instrument (n = 6/each group) was scanned with an atomic force microscopy prior to and after instrumentation. In addition, cyclic fatigue testing was conducted for each instrument (n = 11/each group) with stainless-steel blocks, including 45°-60°-90° degrees of curvature milled to the instruments' size. The roughness parameters increased for both systems after instrumentation (p<0.05). Both systems presented an increased roughness following instrumentation (p<0.05). The cyclic fatigue resistance was lowest at 90° for both systems (p<0.05), whereas the Rotate files presented a higher resistance than that of the Mtwo files (p<0.05). Compared to the Mtwo files, Rotate files presented better resistance, while the resistance decreased as the curvature increased., Competing Interests: The authors have declared that no competing interests exist., (Copyright: © 2024 Özel et al. This is an open access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.)

The current study presents the synergistic effects of fibrillated cellulose (FC) and nickel-titanium (NiTi) alloy on the performance properties of smart composites. Epoxy resin was reinforced with loadings of 1 %, 3 %, and 5 % FC and 3 % NiTi. The composites were produced using the casting method. The morphological properties have been analyzed using scanning electron microscopy (SEM). For mechanical properties, yield strength, modulus of elasticity, hardness, and impact energy were determined. The corrosion rate was determined via electrochemical corrosion testing. The recovery test was used to measure the shape-memory of the composites. The self-healing of the artificial defect in the composites was observed using a thermal camera. The yield strength, modulus of elasticity, hardness, and impact energy of composites reinforced with 5 % FC and 3 % NiTi increased by 168.2 %, 290 %, 33.3 %, and 114.3 %, respectively, compared to pure epoxy resin. There has been a 56.3 % decrease in the corrosion rate. The percentage of composites that returned from the final state to the original state after a deformation was 4 %. Self-healing analysis revealed that the scratch defect in composites was healed after 24 h. It is concluded that smart composites can be used in the aviation and automotive industries., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

The construction of assays is capable of accurately detecting cytokeratin-19 (CYFRA 21-1), which is critical for the rapid diagnosis of nonsmall cell lung cancer. In this work, a novel electrochemiluminescence (ECL) immunosensor based on the co-reaction promotion of luminol@Au@Ni-Co nanocages (NCs) as ECL probe by Ti 3 C 2 T x MXene@TiO 2 -MoS 2 hybrids as co-reaction accelerator was proposed to detect CYFRA 21-1. Ni-Co NCs, as a derivative of Prussian blue analogs, can be loaded with large quantities of Au NPs, luminol, and CYFRA 21-1 secondary antibodies due to their high specific surface area. To further improve the sensitivity of the developed ECL immunosensor, Ti 3 C 2 T x MXene@TiO 2 -MoS 2 hybrids were prepared by in situ growth of TiO 2 nanosheets on highly conductive Ti 3 C 2 T x MXene, and MoS 2 was homogeneously grown on Ti 3 C 2 T x MXene@TiO 2 surfaces by the hydrothermal method. Ti 3 C 2 T x MXene@TiO 2 -MoS 2 hybrids possess excellent catalytic performance on the electro-redox of H 2 O 2 generating more O 2 ·- and obtaining optimal ECL intensity of the luminol/H 2 O 2 system. Under the appropriate experimental conditions, the quantitative detection range of CYFRA 21-1 was from 0.1 pg mL -1 to 100 ng mL -1 , and the limit of detection (LOD) was 0.046 pg mL -1 . The present sensor has a lower LOD with a wider linear range, which provides a new analytical assay for the early diagnosis of small-cell-type lung cancer labels.

Formamide condensation with Ni can generate the NC structure, widely recognized as an efficient catalyst for electrocatalytic CO 2 reduction reaction (CO 2 RR). To improve the utilization efficiency of Ni atoms, we introduced metal oxides as substrates to modulate the growth of a formamide-Ni (FA-Ni) condensate. FA-Ni@TiO 2 demonstrated 2.8 times higher partial CO current density and Ni turnover frequency than FA-Ni, which were also higher than those of other FA-Ni@metal oxides, including ZrO 2 , Al 2 O 3 , Fe 2 O 3 , and ZnO. The improved performance of CO 2 RR can be attributed to the Ni content exposed on FA-Ni@TiO 2 being twice that of the raw FA-Ni condensate. The Fourier transform infrared results suggested that formamide was adsorbed on TiO 2 via the -CHO group, exposing -NH 2 for potential interaction with Ni. As a result, Ni atoms were predispersed on the TiO 2 surface. By contrast, the dispersion of Ni atoms was not enhanced by other metal oxides, such as Al 2 O 3 , Fe 2 O 3 , and ZnO, owing to the robust acidity of their surface sites. These metal oxides adsorbed formamide via -NH 2 , leading to the absence of extra -NH 2 available for binding to Ni atoms. This study provides new insights into the development of appropriate substrates for single-atom catalysts., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier B.V.)

Background: The aim of this study was to evaluate the phase composition, phase transformation temperatures, bending property, and cyclic fatigue resistance of different heat-treated nickel-titanium (NiTi) rotary instruments with the same tip diameter and taper at room (RT; 25 ± 1 °C) and body (BT; 37 ± 1 °C) temperatures., Methods: Five heat-treated NiTi rotary instruments, HyFlex EDM (EDM), HyFlex CM (CM), Vortex Blue (VB), RE file CT (RE) and JIZAI, and a non-heat-treated NiTi rotary instrument (Mtwo) with a size 40, 0.04 taper were investigated. Temperature-dependent phase transformation was examined with differential scanning calorimetry (DSC). The bending loads of the instruments at RT and BT were evaluated using a cantilever-bending test. Cyclic fatigue resistance at RT and BT was measured using a dynamic test, during which the instruments were rotated in combination with a 2-mm back-and-forth motion in an artificial curved canal, and the number of cycles to failure (NCF) was determined. The results were analyzed using two-way repeated measures analysis of variance, a simple main effect test, and the Bonferroni test (α = 0.05)., Results: DSC results indicated that EDM and Mtwo were primarily composed of martensite/R-phase and austenite, respectively, while the other heat-treated instruments were composed of a mix of martensite/R-phase and austenite at the tested temperatures. Regardless of the temperature setting, the bending loads of heat-treated instruments were significantly lower than those of Mtwo (p < 0.05). EDM showed the lowest bending loads and highest NCF at both temperatures (p < 0.05). CM, VB, and JIZAI showed significantly higher bending loads at BT than at RT (p < 0.05). The NCF of all the heat-treated instruments, except VB, was lower at BT than at RT (p < 0.05). At BT, the NCF of CM, VB, RE, and JIZAI were not significantly higher than that of Mtwo (p > 0.05)., Conclusions: Heat-treated NiTi instruments exhibited lower bending loads and higher NCF values than Mtwo. However, this tendency was less pronounced at BT than at RT, especially in the NCF values of instruments with a mixture of martensite/R-phase and austenite phases at the tested temperatures., (© 2023. The Author(s).)