Search

Objective: To evaluate the effect of chest size on coronary calcium score (CCS) as assessed with new-generation CT systems from 4 major vendors., Methods: An anthropomorphic, small-sized (300 × 200 mm) chest phantom containing 100 small calcifications (diameters, 0.5-2.0 mm) was evaluated with and without an extension ring on state-of-the-art CT systems from 4 vendors. The extension ring was used to mimic a patient with a large chest size (400 × 300 mm). Image acquisition was repeated 5 times with small translations and/or rotations. Routine clinical acquisition and reconstruction protocols for small and large patients were used. CCS was quantified as Agatston and mass scores with vendor software., Results: The small-sized phantom resulted in median (interquartiles) Agatston scores of 10 (9-35), 136 (123-146), 34 (30-37), and 87 (85-89) for Philips, GE, Siemens, and Toshiba, respectively. Mass scores were 4 mg (3-9 mg), 23 mg (21-27 mg), 8 mg (8-9 mg), and 20 mg (20-20 mg), respectively. Adding the extension ring resulted in reduced Agatston scores for all vendors (17%-48%) and mass scores for 2 vendors (11%-49%). Median Agatston scores decreased to 9 (5-10), 79 (60-80), 27 (24-32), and 45 (29-53) units, and median mass scores remained similar for Philips at 4 mg (4-6 mg) and Siemens at 8 mg (7-8 mg) and decreased for the other vendors to 13 mg (11-14 mg) and 10 mg (8-13 mg), respectively., Conclusion: This multivendor phantom study showed that CCS can be underestimated up to 50% (49%-66%) for Agatston scores and 49% (36%-59%) for mass scores at a larger chest size, which may be relevant for women and large patients. However, CCS underestimation by chest size differs considerably by vendor., (Copyright © 2015 Society of Cardiovascular Computed Tomography. Published by Elsevier Inc. All rights reserved.)

Objectives: Typical streak artifacts known as metal artifacts occur in the presence of strongly attenuating materials in computed tomography (CT). Recently, vendors have started offering metal artifact reduction (MAR) techniques. In addition, a MAR technique called the metal deletion technique (MDT) is freely available and able to reduce metal artifacts using reconstructed images. Although a comparison of the MDT to other MAR techniques exists, a comparison of commercially available MAR techniques is lacking. The aim of this study was therefore to quantify the difference in effectiveness of the currently available MAR techniques of different scanners and the MDT technique., Materials and Methods: Three vendors were asked to use their preferential CT scanner for applying their MAR techniques. The scans were performed on a Philips Brilliance ICT 256 (S1), a GE Discovery CT 750 HD (S2) and a Siemens Somatom Definition AS Open (S3). The scans were made using an anthropomorphic head and neck phantom (Kyoto Kagaku, Japan). Three amalgam dental implants were constructed and inserted between the phantom's teeth. The average absolute error (AAE) was calculated for all reconstructions in the proximity of the amalgam implants., Results: The commercial techniques reduced the AAE by 22.0±1.6%, 16.2±2.6% and 3.3±0.7% for S1 to S3 respectively. After applying the MDT to uncorrected scans of each scanner the AAE was reduced by 26.1±2.3%, 27.9±1.0% and 28.8±0.5% respectively. The difference in efficiency between the commercial techniques and the MDT was statistically significant for S2 (p=0.004) and S3 (p<0.001), but not for S1 (p=0.63)., Conclusions: The effectiveness of MAR differs between vendors. S1 performed slightly better than S2 and both performed better than S3. Furthermore, for our phantom and outcome measure the MDT was more effective than the commercial MAR technique on all scanners.

Radiotherapy and particle therapy treatment planning require accurate knowledge of the electron density and elemental composition of the tissues in the beam path to predict the local dose deposition. We describe a method for the analysis of dual energy computed tomography (DECT) images that provides the electron densities and effective atomic numbers of tissues. The CT measurement process is modelled by system weighting functions, which apply an energy dependent weighting to the parameterization of the total cross section for photon interactions with matter. This detailed parameterization is based on the theoretical analysis of Jackson and Hawkes and deviates, at most, 0.3% from the tabulated NIST values for the elements H to Zn. To account for beam hardening in the object as present in the CT image we implemented an iterative process employing a local weighting function, derived from the method proposed by Heismann and Balda. With this method effective atomic numbers between 1 and 30 can be determined. The method has been experimentally validated on a commercially available tissue characterization phantom with 16 inserts made of tissue substitutes and aluminium that has been scanned on a dual source CT system with tube potentials of 100 kV and 140 kV using a clinical scan protocol. Relative electron densities of all tissue substitutes have been determined with accuracy better than 1%. The presented DECT analysis method thus provides high accuracy electron densities and effective atomic numbers for radiotherapy and especially particle therapy treatment planning.

Iterative reconstruction techniques for coronary CT angiography have been introduced as an alternative for traditional filter back projection (FBP) to reduce image noise, allowing improved image quality and a potential for dose reduction. However, the impact of iterative reconstruction on the coronary artery calcium score is not fully known. In 112 consecutive stable patients with suspected coronary artery disease, the coronary calcium scores were assessed. Comparisons were made between the Agatston, volume and mass scores obtained with traditional FBP, and by using adaptive statistical iterative reconstruction (ASIR). A significant reduction of the Agatston score, volume score and mass score was observed for ASIR when compared to FBP, with median differences of resp. 26, 5 mm(3) and 1 mg. Using the ASIR reconstruction, the number of patients with a calcium score of zero increased by 13 %. Iterative CT reconstruction significantly reduces the Agatston, volume and mass scores. Since the calcium score is used as a prognostic tool for coronary artery disease, caution must be taken when using iterative reconstruction.

The aim of this study was to compare the summing method (A) with the complement method (B) for calculating the cumulative lifetime-attributable-risk (LAR(tot)) of tumor incidence and mortality of multiple CT exposures. Method A defines LAR(tot) as the summation of the risk of each separate exposure. Method B was defined as the complement of the probability of inducing no cancer in N separate exposures. The risk of each separate exposure was estimated using dose, gender, and age at exposure (BEIR VII phase 2). Both methods were compared in a simulation and applied to a database of 11,884 patients exposed to multiple CTs. The relative difference between the methods was defined as ΔP%. Simulation confirmed that Method A always overestimates LAR(tot). ΔP% was proportional to the dose per exposure and the number of exposures. The differences between Methods A and B were small. Average LAR(tot) of tumor incidence was 0.140% (Method A) and 0.139% (Method B) with maxima of 5.70% and 5.56%, respectively. Average LAR(tot) of mortality was 0.085% for both methods, with maxima of 2.20% and 2.18%, respectively. ΔP% was highest (2.43%) for a female patient (3-y old) exposed to eight recurrent scans and a cumulative dose of 144 mSv. Although Method B is more accurate, both methods can be used to estimate the cumulative risk of multiple CT exposures. These results have to be interpreted, however, in the perspective of the uncertainties in the cancer risk model, which have been estimated at a factor of 2 or 3.

Computed tomography (CT) scans are indispensable in modern medicine; however, the spectacular rise in global use coupled with relatively high doses of ionizing radiation per examination have raised radiation protection concerns. Children are of particular concern because they are more sensitive to radiation-induced cancer compared with adults and have a long lifespan to express harmful effects which may offset clinical benefits of performing a scan. This paper describes the design and methodology of a nationwide study, the Dutch Pediatric CT Study, regarding risk of leukemia and brain tumors in children after radiation exposure from CT scans. It is a retrospective record-linkage cohort study with an expected number of 100,000 children who received at least one electronically archived CT scan covering the calendar period since the introduction of digital archiving until 2012. Information on all archived CT scans of these children will be obtained, including date of examination, scanned body part and radiologist's report, as well as the machine settings required for organ dose estimation. We will obtain cancer incidence by record linkage with external databases. In this article, we describe several approaches to the collection of data on archived CT scans, the estimation of radiation doses and the assessment of confounding. The proposed approaches provide useful strategies for data collection and confounder assessment for general retrospective record-linkage studies, particular those using hospital databases on radiological procedures for the assessment of exposure to ionizing or non-ionizing radiation.

Objective: The purpose of this study is to evaluate observer detection and volume measurement of small irregular solid artificial pulmonary nodules on 64-MDCT in an anthropomorphic thoracic phantom., Materials and Methods: Forty in-house-made solid pulmonary nodules (lobulated and spiculated; actual volume, 5.1-88.4 mm3; actual CT densities, -51 to 157 HU) were randomly placed inside an anthropomorphic thoracic phantom with pulmonary vasculature. The phantom was examined on two 64-MDCT scanners, using a scan protocol as applied in lung cancer screening. Two independent blinded observers screened for pulmonary nodules. Nodule volume was evaluated semiautomatically using dedicated software and was compared with the actual volume using an independent-samples t test. The interscanner and interobserver agreement of volumetry was assessed using Bland-Altman analysis., Results: Observer detection sensitivity increased along with increasing size of irregular nodules. Sensitivity was 100% when the actual volume was at least 69 mm3, regardless of specific observer, scanner, nodule shape, and density. Overall, nodule volume was underestimated by (mean±SD) 18.9±11.8 mm3 (39%±21%; p<0.001). The relative interscanner difference of volumetry was 3.3% (95% CI, -33.9% to 40.4%). The relative interobserver difference was 0.6% (-33.3% to 34.5%)., Conclusion: Small irregular solid pulmonary nodules with an actual volume of at least 69 mm3 are reliably detected on 64-MDCT. However, CT-derived volume of those small nodules is largely underestimated, with considerable variation.

Objective: To evaluate the diagnostic performance of computed tomography angiography (CTA) and contrast-enhanced magnetic resonance angiography (CE-MRA) in detecting haemodynamically significant arterial stenosis or occlusion in patients with critical limb ischaemia (CLI) or intermittent claudication (IC)., Methods: Medline and Embase were searched for studies comparing CTA or CE-MRA with digital subtraction angiography as a reference standard, including patients with CLI or IC. Outcome measures were aortotibial arterial stenosis of more than 50 % or occlusion. Methodological quality of studies was assessed using QUADAS., Results: Out of 5,693 articles, 12 CTA and 30 CE-MRA studies were included, respectively evaluating 673 and 1,404 participants. Summary estimates of sensitivity and specificity were respectively 96 % (95 % CI, 93-98 %) and 95 % (95 % CI, 92-97 %) for CTA, and 93 % (95 % CI, 91-95 %) and 94 % (95 % CI, 93-96 %) for CE-MRA. Regression analysis showed that the prevalence of CLI in individual studies was not an independent predictor of sensitivity and specificity for either technique. Methodological quality of studies was moderate to good., Conclusion: CTA and CE-MRA are accurate techniques for evaluating disease severity of aortotibial arteries in patients with CLI or IC. No significant differences in the diagnostic performance of the two techniques between patients with CLI and IC were found., Key Points: • Computed tomography and contrast-enhanced magnetic resonance angiography can both demonstrate arterial disease. • CTA and CE-MRA can both accurately evaluate arteries in peripheral arterial disease. • Diagnostic performances of critical limb ischaemia and intermittent claudication are not different. • Separate imaging technique of tibial arteries by CE-MRA is preferred. • CTA and CE-MRA can distinguish confidently between high-grade stenoses and occlusions.

Objectives: To evaluate the diagnostic accuracy of computed tomography angiography (CTA) in detecting arterial lesions in patients with suspected arterial injury of the upper or lower extremity due to trauma., Methods: A systematic review and meta-analysis was carried out. Medline and Embase were searched on August 13, 2012, for studies comparing CTA with surgery, digital subtraction angiography (DSA), or follow-up, which allowed extraction of data into two-by-two tables. The methodological quality of included studies was assessed using the QUADAS tool. Summary estimates of sensitivity and specificity of CTA in identifying or excluding arterial lesions were obtained using a bivariate model., Results: This review included 11 studies making up a total of 891 trauma patients. The included studies were of moderate methodological quality and at risk of misclassification and verification bias. Some 4.2% of all CTA studies were non-diagnostic. The summary estimates of sensitivity and specificity of CTA were 96.2% (95% CI 93.5-97.8%) and 99.2% (95% CI 96.8-99.8%), respectively., Conclusion: Despite methodological flaws, the excellent estimates of sensitivity and specificity indicate that CTA is an accurate modality for evaluating arterial lesions in patients with extremity trauma and can replace DSA., (Copyright © 2013 European Society for Vascular Surgery. Published by Elsevier Ltd. All rights reserved.)

Objective: To assess inter- and intrascanner variability in volumetry of solid pulmonary nodules in an anthropomorphic thoracic phantom using low-dose CT., Methods: Five spherical solid artificial nodules [diameters 3, 5, 8, 10 and 12 mm; CT density +100 Hounsfield units (HU)] were randomly placed inside an anthropomorphic thoracic phantom in different combinations. The phantom was examined on two 64-row multidetector CT (64-MDCT) systems (CT-A and CT-B) from different vendors with a low-dose protocol. Each CT examination was performed three times. The CT examinations were evaluated twice by independent blinded observers. Nodule volume was semi-automatically measured by dedicated software. Interscanner variability was evaluated by Bland-Altman analysis and expressed as 95% confidence interval (CI) of relative differences. Intrascanner variability was expressed as 95% CI of relative variation from the mean., Results: No significant difference in CT-derived volume was found between CT-A and CT-B, except for the 3-mm nodules (p<0.05). The 95% CI of interscanner variability was within ±41.6%, ±18.2% and ±4.9% for 3, 5 and ≥8 mm nodules, respectively. The 95% CI of intrascanner variability was within ±28.6%, ±13.4% and ±2.6% for 3, 5 and ≥8 mm nodules, respectively., Conclusion: Different 64-MDCT scanners in low-dose settings yield good agreement in volumetry of artificial pulmonary nodules between 5 mm and 12 mm in diameter. Inter- and intrascanner variability decreases at a larger nodule size to a maximum of 4.9% for ≥8 mm nodules., Advances in Knowledge: The commonly accepted cut-off of 25% to determine nodule growth has the potential to be reduced for ≥8 mm nodules. This offers the possibility of reducing the interval for repeated CT scans in lung cancer screenings.

Purpose: Coronary artery calcium score, traditionally based on electrocardiography (ECG)-triggered computed tomography (CT), predicts cardiovascular risk. However, nontriggered CT is extensively utilized. The study-purpose is to evaluate the in vitro agreement in coronary calcium score between nontriggered thoracic CT and ECG-triggered cardiac CT., Methods: Three artificial coronary arteries containing calcifications of different densities (high, medium, and low), and sizes (large, medium, and small), were studied in a moving cardiac phantom. Two 64-detector CT systems were used. The phantom moved at 0-90 mm∕s in nontriggered low-dose CT as index test, and at 0-30 mm∕s in ECG-triggered CT as reference. Differences in calcium scores between nontriggered and ECG-triggered CT were analyzed by t-test and 95% confidence interval. The sensitivity to detect calcification was calculated as the percentage of positive calcium scores., Results: Overall, calcium scores in nontriggered CT were not significantly different to those in ECG-triggered CT (p>0.05). Calcium scores in nontriggered CT were within the 95% confidence interval of calcium scores in ECG-triggered CT, except predominantly at higher velocities (≥50 mm∕s) for the high-density and large-size calcifications. The sensitivity for a nonzero calcium score was 100% for large calcifications, but 46%±11% for small calcifications in nontriggered CT., Conclusions: When performing multiple measurements, good agreement in positive calcium scores is found between nontriggered thoracic and ECG-triggered cardiac CT. Agreement decreases with increasing coronary velocity. From this phantom study, it can be concluded that a high calcium score can be detected by nontriggered CT, and thus, that nontriggered CT likely can identify individuals at high risk of cardiovascular disease. On the other hand, a zero calcium score in nontriggered CT does not reliably exclude coronary calcification.

Objective: To retrospectively investigate whether optimisation of volume-doubling time (VDT) cutoff for fast-growing nodules in lung cancer screening can reduce false-positive referrals., Methods: Screening participants of the NELSON study underwent low-dose CT. For indeterminate nodules (volume 50-500 mm(3)), follow-up CT was performed 3 months after baseline. A negative baseline screen resulted in a regular second-round examination 1 year later. Subjects referred to a pulmonologist because of a fast-growing (VDT <400 days) solid nodule in the baseline or regular second round were included in this study. Histology was the reference for diagnosis, or stability on subsequent CTs, confirming benignity. Mean follow-up of non-resected nodules was 4.4 years. Optimisation of the false-positive rate was evaluated at maintained sensitivity for lung cancer diagnosis with VDT <400 days as reference., Results: Sixty-eight fast-growing nodules were included; 40 % were malignant. The optimal VDT cutoff for the 3-month follow-up CT after baseline was 232 days. This cutoff reduced false-positive referrals by 33 % (20 versus 30). For the regular second round, VDTs varied more among malignant nodules, precluding lowering of the VDT cutoff of 400 days., Conclusion: All malignant fast-growing lung nodules referred after the 3-month follow-up CT in the baseline lung cancer screening round had VDT ≤232 days. Lowering the VDT cutoff may reduce false-positive referrals., Key Points: • Lung nodules are common in CT lung cancer screening, most being benign • Short-term follow-up CT can identify fast-growing intermediate-size lung nodules • Most fast-growing nodules on short-term follow-up CT still prove to be benign • A new volume-doubling time (VDT) cut-off is proposed for lung screening • The optimised VDT cutoff may decrease false-positive case referrals for lung cancer.

Introduction: Multi detector computed tomography (MDCT) underestimates the coronary calcium score as compared to electron beam tomography (EBT). Therefore clinical risk stratification based on MDCT calcium scoring may be inaccurate. The aim of this study was to assess the feasibility of a new phantom which enables establishment of a calcium scoring protocol for MDCT that yields a calcium score comparable to the EBT values and to the physical mass., Materials and Methods: A phantom containing 100 small calcifications ranging from 0.5 to 2.0mm was scanned on EBT using a standard coronary calcium protocol. In addition, the phantom was scanned on a 320-row MDCT scanner using different scanning, reconstruction and scoring parameters (tube voltage 80-135 kV, slice thickness 0.5-3.0mm, reconstruction kernel FC11-FC15 and threshold 110-150 HU). The Agatston and mass score of both modalities was compared and the influence of the parameters was assessed., Results: On EBT the Agatston and mass scores were between 0 and 20, and 0 and 3mg, respectively. On MDCT the Agatston and mass scores were between 0 and 20, and 0 and 4 mg, respectively. All parameters showed an influence on the calcium score. The Agatston score on MDCT differed 52% between the 80 and 135kV, 65% between 0.5 and 3.0mm and 48% between FC11 and FC15. More calcifications were detected with a lower tube voltage, a smaller slice thickness, a sharper kernel and a lower threshold. Based on these observations an acquisition protocol with a tube voltage of 100 kV and two reconstructions protocols were defined with a FC12 reconstruction kernel; one with a slice thickness of 3.0mm and a one with a slice thickness of 0.5mm. This protocol yielded an Agatston score as close to the EBT as possible, but also a mass score as close to the physical phantom value as possible, respectively., Conclusion: With the new phantom one acquisition protocol and two reconstruction protocols can be defined which produces Agatston scores comparable to EBT values and to the physical mass., (Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.)

Objective: To assess the sensitivity of detection and accuracy of volumetry by manual and semi-automated quantification of artificial pulmonary nodules in an anthropomorphic thoracic phantom on low-dose CT., Methods: Fifteen artificial spherical nodules (diameter 3, 5, 8, 10 and 12 mm; CT densities -800, -630 and +100 HU) were randomly placed inside an anthropomorphic thoracic phantom. The phantom was examined on 16- and 64-row multidetector CT with a low-dose protocol. Two independent blinded observers screened for pulmonary nodules. Nodule diameter was measured manually, and volume calculated. For solid nodules (+100 HU), diameter and volume were also evaluated by semi-automated software. Differences in observed volumes between the manual and semi-automated method were evaluated by a t-test., Results: Sensitivity was 100 % for all nodules of >5 mm and larger, 60-80 % for solid and 0-20 % for non-solid 3-mm nodules. No false-positive nodules but high inter-observer reliability and inter-technique correlation were found. Volume was underestimated manually by 24.1 ± 14.0 % for nodules of any density, and 26.4 ± 15.5 % for solid nodules, compared with 7.6 ± 8.5 % (P < 0.01) semi-automatically., Conclusion: In an anthropomorphic phantom study, the sensitivity of detection is 100 % for nodules of >5 mm in diameter. Semi-automated volumetry yielded more accurate nodule volumes than manual measurements.

Objectives: The purpose of this study was to assess the thermal sensitivity of CT during heating of ex-vivo animal liver., Methods: Pig liver was indirectly heated from 20 to 90 °C by passage of hot air through a plastic tube. The temperature in the heated liver was measured using calibrated thermocouples. In addition, image acquisition was performed with a multislice CT scanner before and during heating of the liver sample. The reconstructed CT images were then analysed to assess the change of CT number as a function of temperature., Results: During heating, a decrease in CT numbers was observed as a hypodense area on the CT images. In addition, the hypodense area extended outward from the heat source during heating. The analysis showed a linear decrease of CT number as a function of temperature. From this relationship, we derived a thermal sensitivity of CT for pig liver tissue of -0.54±0.03 HU °C(-1) with an r(2) value of 0.91., Conclusions: The assessment of the thermal sensitivity of CT in ex-vivo pig liver tissue showed a linear dependency on temperature ≤90 °C. This result may be beneficial for the application of isotherms or thermal maps in CT images of liver tissue.

Purpose: To evaluate the feasibility and accuracy of a model for tissue characterization with dual source computed tomography (DSCT)., Methods and Materials: A model for tissue characterization in CT was used with a parameterization of linear attenuation coefficients. Sixteen chemical substances with effective atomic numbers between 5.21 and 13.08 and electron densities between 2.20 and 4.12 x10(23) electrons/cm(3) were scanned at energies of 80 and 140 kV on a DSCT. From the reconstructed dual energy data sets, effective atomic numbers and electron densities of the substances were calculated., Results: Our presented model using DSCT approximated the effective atomic numbers and effective electron densities of 16 substances very well. The measured effective atomic numbers deviated 3.4 ± 6.8% (R(2) = 0.994) from theoretical effective atomic numbers. In addition, measured effective electron densities deviated -0.6 ± 2.2% (R(2) = 0.999) from theoretical effective electron densities., Conclusion: Effective atomic numbers and effective electron densities can be determined with a high accuracy with DSCT. Therefore the model can be of potential benefit for clinical applications of quantitative tissue characterization with DSCT., (Copyright © 2011 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.)

Objectives: To assess the feasibility of computed tomography (CT) based thermometry during interstitial laser heating in the bovine liver., Methods: Four freshly exercised cylindrical blocks of bovine tissue were heated using a continuous laser of Nd:YAG (wavelength: 1064 nm, active length: 30 mm, power: 10-30 W). All tissues were imaged at least once before and 7 times during laser heating using CT and temperatures were simultaneously measured with 5 calibrated thermal sensors. The dependency of the average CT numbers as a function of temperature was analysed with regression analysis and a CT thermal sensitivity was derived., Results: During laser heating, the growing hypodense area was observed around the laser source and that area showed an increase as a function of time. The formation of hypodense area was caused by declining in CT numbers at increasing temperatures. The regression analysis showed an inverse linear dependency between temperature and average CT number with -0.65 ± 0.048 HU/°C (R(2) = 0.75) for the range of 18-85°C in bovine liver., Conclusions: The non-invasive CT based thermometry during interstitial laser heating is feasible in the bovine liver. CT based thermometry could be further developed and may be of potential use during clinical LITT of the liver.

Purpose: The purpose of this study was to assess the feasibility of noninvasive thermometry using high-resolution computer tomography (CT) for the monitoring of bovine liver during radiofrequency (RF) ablation., Methods: Radiofrequency probes were used to ablate bovine livers from 20°C to 98°C. During the heating process, images were acquired using a multidetector CT scanner with simultaneous measurement of temperature using calibrated thermal sensors. The CT scanner's thermal sensitivity was derived from the correlation between the CT numbers and temperature. The CT scanner's thermal sensitivity was used to compute a temperature map, and this temperature map was overlaid on the original CT scan using a dedicated software application., Results: The CT numbers of the bovine liver showed a linear decline with an increase in temperature and a CT thermal sensitivity of -0.60 ± 0.026 Hounsfield unit/°C (R² = 0.87). Temperature maps were calculated using this correlation and were superimposed onto the CT scans presenting temperature distribution around the RF probe in the bovine liver., Conclusions: Noninvasive temperature determination is feasible during RF ablation of bovine liver using a high-resolution CT system. Therefore, the proposed method can be of potential use in clinical practice for noninvasive temperature mapping during ablation.

Purpose: To compare coronary computed tomographic (CT) angiography with first-pass magnetic resonance (MR) myocardial perfusion imaging in patients with chest pain and low to intermediate probability of coronary artery disease (CAD)., Materials and Methods: Local ethics committee approval and patient written informed consent were obtained. Patients with chest pain and low to intermediate pretest probability of CAD underwent both coronary CT angiography and MR myocardial perfusion imaging. Coronary CT angiographic and MR myocardial perfusion images were analyzed qualitatively by blinded observers. Obstructive CAD was defined as more than 50% diameter stenosis at coronary CT angiography. Data were expressed with 95% confidence intervals (CIs) calculated from binomial expression., Results: In 145 (94.2%) of 154 eligible patients, both coronary CT angiography and MR myocardial perfusion imaging were performed successfully. Mean age was 57 years +/- 10 (standard deviation), and 45.5% of patients were male. Mean interval between coronary CT angiography and MR myocardial perfusion imaging was 4.6 days +/- 3.0; median was 5.0 days. CT coronary angiography revealed obstructive CAD in 52 (35.9%) patients and 78 (17.9%) coronary arteries. At MR myocardial perfusion imaging, myocardial ischemia was demonstrated in 33 (22.8%) patients and 59 (13.6%) vessel territories. Of patients without CAD at coronary CT angiography, 90.5% (57 of 63; 95% CI: 82.6%, 95.0%) had normal myocardial perfusion at MR myocardial perfusion imaging. Of patients with nonobstructive CAD, 83.3% (25 of 30; 95% CI: 69.5%, 91.6%) had normal myocardial perfusion at MR myocardial perfusion imaging. Myocardial ischemia was detected at MR myocardial perfusion imaging in 42.3% (22 of 52; 95% CI: 29.5%, 56%) of patients with obstructive CAD at coronary CT angiography., Conclusion: MR myocardial perfusion imaging and coronary CT angiography have complementary roles in evaluation of patients who are suspected of having CAD. Coronary CT angiography can be used to reliably rule out CAD, but its capability to demonstrate hemodynamically significant CAD is limited. The combination of both techniques enables the clinician to evaluate morphology and functional relevance of CAD comprehensively and noninvasively., ((c) RSNA, 2010.)

To assess whether absolute mass scores are comparable or differ between identical 64-slice MDCT scanners of the same manufacturer and to compare absolute mass scores to the physical mass and between scan modes using a calcified phantom. A non-moving anthropomorphic phantom with nine calcifications of three sizes and three densities was scanned 30 times on three 64-slice MDCT scanners of manufacturer A and on three 64-slice MDCT scanners of manufacturer B in both sequential and spiral scan mode. The mean mass scores and mass score variabilities of seven calcifications were determined for all scanners; two non-detectable calcifications were omitted. It was analyzed whether identical scanners yielded similar or significantly different mass scores. Furthermore mass scores were compared to the physical mass and mass scores were compared between scan modes. The mass score calibration factor was determined for all scanners. Mass scores obtained on identical scanners were similar for almost all calcifications. Overall, mass score differences between the scanners were small ranging from 1.5 to 3.4% for the total mass scores, and most differences between scanners were observed for high density calcifications. Mass scores were significantly different from the physical mass for almost all calcifications and all scanners. In sequential mode the total physical mass (167.8 mg) was significantly overestimated (+2.3%) for 4 out of 6 scanners. In spiral mode a significant overestimation (+2.5%) was found for system B and a significant underestimation (-1.8%) for two scanners of system A. Mass scores were dependent on the scan mode, for manufacturer A scores were higher in sequential mode and for manufacturer B in spiral mode. For system A using spiral scan mode no differences were found between identical scanners, whereas a few differences were found using sequential mode. For system B the scan mode did not affect the number of different mass scores between identical scanners. Mass scores obtained in the same scan mode are comparable between identical 64-slice CT scanners and identical 64-slice CT scanners on different sites can be used in follow-up studies. Furthermore, for all systems significant differences were found between mass scores and the physical calcium mass; however, the differences were relatively small and consistent.

Purpose: The objective of this study is to quantify the influence of linear motion, calcification density, and temporal resolution on coronary calcium determination using multidetector computed tomography (MDCT), dual source CT (DSCT), and electron beam tomography (EBT) and to find a quantitative method which corrects for the influences of these parameters using a linear moving cardiac phantom., Methods: On a robotic arm with artificial arteries with four calcifications of increasing density, a linear movement was applied between 0 and 120 mm/s (step of 10 mm/s). The phantom was scanned five times on 64-slice MDCT, DSCT, and EBT using a standard acquisition protocol. The average Agatston, volume, and mass scores were determined for each velocity, calcification, and scanner. Susceptibility to motion was quantified using a cardiac motion susceptibility (CMS) index. Resemblance to EBT and physical volume and mass was quantified using a Delta index., Results: Increasing motion artifacts were observed at increasing velocities on all scanners, with increasing severity from EBT to DSCT to 64-slice MDCT. The calcium score showed a linear dependency on motion from which a correction factor could be derived. This correction factor showed a linear dependency on the mean calcification density with a good fit for all three scoring methods and all three scanners (0.73 < or = R2 < or = 0.95). The slope and offset of this correction factor showed a linear dependency on temporal resolution with a good fit for all three scoring methods and all three scanners (0.83 < or = R2 < or = 0.98). CMS was minimal for EBT and increasing values were observed for DSCT and highest values for 64-slice MDCT. CMS was minimal for mass score and increasing values were observed for volume score and highest values for Agatston score. For all densities and scoring methods DSCT showed on average the closest resemblance to EBT calcium scores. When using the correction factor, CMS index decreased on average by 15% and Delta index decreased by 35%., Conclusions: Calcium scores determined on DSCT and 64-slice MDCT are highly susceptible to motion as compared to EBT. The mass score is less susceptible to motion compared to volume and Agatston score. Calcium scores determined on DSCT bear a closer resemblance to EBT obtained calcium scores than 64-slice MDCT. In addition, the calcium score is highly dependent on the average density of individual calcifications and the dependency of the calcium score on motion showed a linear behavior on calcification density. From these relations, a quantitative method could be derived which corrects the measured calcium score for the influence of linear motion, mean calcification density, and temporal resolution.

Purpose: ECG-gated CT enables the visualization of motions caused by the beating of the heart. Although ECG gating is frequently used in cardiac CT imaging, this technique is also very promising for evaluating vessel wall motion of the aortic artery and the motions of (stent grafts inside) abdominal aortic aneurysms (AAA). Late stent graft failure is a serious complication in endovascular repair of aortic aneurysms. Better understanding of the motion characteristics of stent grafts will be beneficial for designing future devices. In addition, these data can be valuable in predicting stent graft failure in patients. To be able to reliably quantify the motion, however, it is of importance to know the performance and limitations of ECG gating, especially when the motions are small, as is the case in AAA. Since the details of the reconstruction algorithms are proprietary information on the CT manufacturers and not in the public domain, empirical experiments are required. The goal of this study is to investigate as to what extent the motions in AAA can be measured using ECG-gated CT. The authors quantitatively investigate four aspects of motion in ECG-gated CT: The detectability of the motion of objects at different amplitudes and different periodic motions, the temporal resolution, and the volume gaps that occur as a function of heart rate., Methods: They designed an experiment on a standard static phantom to empirically determine temporal resolution. To investigate motion amplitude and frequency, as well as patient heart rate, they designed dynamic experiments in which a home-made phantom driven by a motion unit moves in a predetermined pattern., Results: The duration of each ECG-gated phase was found to be 185 ms, which corresponds to half of the rotation time and is thus in accordance with half scan reconstruction applied by the scanner. By using subpixel localization, motions become detectable from amplitudes of as small as 0.4 mm in the x direction and 0.7 mm in the z direction. With the rotation time used in this study, motions up to 2.7 Hz can be reliably detected. The reconstruction algorithm fills volume gaps with noisy data using interpolation, but objects within these gaps remain hidden., Conclusions: This study gives insight into the possibilities and limitations for measuring small motions using ECG-gated CT. Application of the experimental method is not restricted to the CT scanner of a single manufacturer. From the results, they conclude that ECG-gated CTA is a suitable technique for studying the expected motions of the stent graft and vessel wall in AAA.

Purpose: To assess the influence of temporal resolution on image quality of computed tomographic (CT) coronary angiography by comparing 64-row Dual Source CT (DSCT) and Single Source CT (SSCT) at different heart rates., Methods: An anthropomorphic moving heart phantom was scanned at rest, and at 50 beats per minute (bpm) up to 110 bpm, with intervals of 10 bpm. 3D volume rendered images and curved multi-planar reconstructions (MPRs) were acquired and image quality of the coronary arteries was rated on a 5-points scale (1=poor image quality with many artefacts, 5=excellent image quality) for each heart rate and each scanner by 3 observers. Paired sample t-test and Wilcoxon Signed Ranks test were used to assess clinically relevant differences between both modalities., Results: The mean image quality scores at 70, 100 and 110 bpm were significantly higher for DSCT compared to SSCT. The overall mean image quality scores for DSCT (4.2+/-0.6) and SSCT (3.0+/-1.1) also differed significantly (p<0.001)., Conclusion: These initial results show a clinically relevant overall higher image quality for DSCT compared to SSCT, especially at heart rates of 70, 100 and 110 bpm. With its comparatively high image quality and low radiation dose, DSCT appears to be the method of choice in CT coronary angiography at heart rates above 70 bpm.

To compare magnetic resonance imaging (MRI), 64-slice multi-detector computed tomography (MDCT) and dual-source computed tomography (DSCT) in assessing global function parameters using a moving heart phantom. A moving heart phantom with known volumes (215-258 ml) moving at 50-100 beats per minute was examined by three different imaging modalities using clinically implemented scanning protocols. End-diastolic and end-systolic volumes were calculated by two experienced observers using dedicated post-processing tools. Ejection fraction (EF) and cardiac output (CO) were calculated and mutually compared using Bland-Altman plots. MRI underestimated the ejection EF by 16.1% with a Bland-Altman interval (B-A) of [-4.35 (-2.48) -0.60]. Sixty-four-slice MDCT overestimated the EF by 2.6% with a relatively wide B-A interval of [-3.40 (0.40) 4.20]. DSCT deviated the least from the known phantom volumes, underestimating the volumes by 0.8% with a B-A interval of [-1.17 (-0.13) 0.91]. CO analysis showed similar results. Furthermore, a good correlation was found between DSCT and MRI for EF and CO results. MRI systematically underestimates functional cardiac parameters, ejection fraction and cardiac output of a moving heart phantom. Sixty-four-slice MDCT underestimates or overestimates these functional parameters depending on the heart rate because of limited spatial resolution. DSCT deviates the least from these functional parameters compared to MRI, EBT and 64-slice MDCT.

The purpose of this paper is to investigate calcium scoring on computed tomography (CT) using an adjusted threshold depending on the maximum Hounsfield value within the calcification (HU(peak)). The volume of 19 calcifications was retrospectively determined on 64-slice multidetector CT and dual source CT (DSCT) at different thresholds and the threshold associated with the physical volume was determined. In addition, approximately 10 000 computer simulations were done simulating the same process for calcifications with mixed density. Using these data a relation between the HU(peak) and the threshold could be established. Hereafter, this relation was assessed by scanning six calcifications in a phantom at 40-110 beats per minute using DSCT. The influence of motion was determined and the measured calcium scores were compared to the physical volumes and mass. A positive linear correlation was found between the scoring threshold and the HU(peak) of the calcifications both for the phantom measurements as for the computer simulations. Using this relation the individual threshold for each calcification could be calculated. Calcium scores of the moving calcifications determined with an adjusted threshold were approximately 30% less susceptible to cardiac motion compared to standard calcium scoring. Furthermore, these scores approximated the physical volume and mass at least 10% better than the standard calcium scores. The threshold in calcium scoring should be adjusted for each individual calcification based on the HU(peak) of the calcification. Calcium scoring using an adjusted threshold is less susceptible to cardiac motion and more accurate compared to the physical values.

Context: Computed tomography angiography (CTA) is an increasingly attractive imaging modality for assessing lower extremity peripheral arterial disease (PAD)., Objective: To determine the accuracy of CTA compared with intra-arterial digital subtraction angiography (DSA) in differentiating extent of disease in patients with PAD., Data Sources and Study Selection: Search of MEDLINE (January 1966-August 2008), EMBASE (January 1980-August 2008), and the Database of Abstracts of Reviews of Effectiveness for studies comparing CTA with intra-arterial DSA for PAD. Eligible studies compared multidetector CTA with intra-arterial DSA, included at least 10 patients with intermittent claudication or critical limb ischemia, aimed to detect more than 50% stenosis or arterial occlusion, and presented either 2 x 2 or 3 x 3 contingency tables (< or = 50% stenosis vs > 50% stenosis or occlusion), or provided data allowing their construction., Data Extraction: Two reviewers screened potential studies for inclusion and independently extracted study data. Methodological quality was assessed by using the QUADAS instrument., Data Synthesis: Of 909 studies identified, 20 (2.2%) met the inclusion criteria. These 20 studies had a median sample size of 33 (range, 16-279) and included 957 patients, predominantly with intermittent claudication (68%). Methodological quality was moderate. Overall, the sensitivity of CTA for detecting more than 50% stenosis or occlusion was 95% (95% confidence interval [CI], 92%-97%) and specificity was 96% (95% CI, 93%-97%). Computed tomography angiography correctly identified occlusions in 94% of segments, the presence of more than 50% stenosis in 87% of segments, and absence of significant stenosis in 96% of segments. Overstaging occurred in 8% of segments and understaging in 15%., Conclusion: Computed tomography angiography is an accurate modality to assess presence and extent of PAD in patients with intermittent claudication; however, methodological weaknesses of examined studies prevent definitive conclusions from these data.

Purpose: Assessment of calcium scoring (Ca-scoring) on a 64-slice multi-detector computed tomography (MDCT) scanner, a dual-source computed tomography (DSCT) scanner and an electron beam tomography (EBT) scanner with a moving cardiac phantom as a function of heart rate, slice thickness and calcium density., Methods and Materials: Three artificial arteries with inserted calcifications of different sizes and densities were scanned at rest (0 beats per minute) and at 50-110 beats per minute (bpm) with an interval of 10 bpm using 64-slice MDCT, DSCT and EBT. Images were reconstructed with a slice thickness of 0.6 and 3.0 mm. Agatston score, volume score and equivalent mass score were determined for each artery. A cardiac motion susceptibility (CMS) index was introduced to assess the susceptibility of Ca-scoring to heart rate. In addition, a difference (Delta) index was introduced to assess the difference of absolute Ca-scoring on MDCT and DSCT with EBT., Results: Ca-score is relatively constant up to 60 bpm and starts to decrease or increase above 70 bpm, depending on scoring method, calcification density and slice thickness. EBT showed the least susceptibility to cardiac motion with the smallest average CMS-index (2.5). The average CMS-index of 64-slice MDCT (9.0) is approximately 2.5 times the average CMS-index of DSCT (3.6). The use of a smaller slice thickness decreases the CMS-index for both CT-modalities. The Delta-index for DSCT at 0.6 mm (53.2) is approximately 30% lower than the Delta-index for 64-slice MDCT at 0.6 mm (72.0). The Delta-indexes at 3.0 mm are approximately equal for both modalities (96.9 and 102.0 for 64-slice MDCT and DSCT respectively)., Conclusion: Ca-scoring is influenced by heart rate, slice thickness and modality used. Ca-scoring on DSCT is approximately 50% less susceptible to cardiac motion as 64-slice MDCT. DSCT offers a better approximation of absolute calcium score on EBT than 64-slice MDCT when using a smaller slice thickness. A smaller slice thickness reduces the susceptibility to cardiac motion and reduces the difference between CT-data and EBT-data. The best approximation of EBT on CT is found for DSCT with a slice thickness of 0.6 mm.

We determined the efficiency of a screening protocol based on coronary calcium scores (CCS) compared with exercise testing in patients with suspected coronary artery disease (CAD), a normal ECG and troponin levels. Three-hundred-and-four patients were enrolled in a screening protocol including CCS by electron beam computed tomography (Agatston score), and exercise testing. Decision-making was based on CCS. When CCS>or=400, coronary angiography (CAG) was recommended. When CCS<10, patients were discharged. Exercise tests were graded as positive, negative or nondiagnostic. The combined endpoint was defined as coronary event or obstructive CAD at CAG. During 12+/-4 months, CCS>or=400, 10-399 and <10 were found in 42, 103 and 159 patients and the combined endpoint occurred in 24 (57%), 14 (14%) and 0 patients (0%), respectively. In 22 patients (7%), myocardial perfusion scintigraphy was performed instead of exercise testing due to the inability to perform an exercise test. A positive, nondiagnostic and negative exercise test result was found in 37, 76 and 191 patients, and the combined endpoint occurred in 11 (30%), 15 (20%) and 12 patients (6%), respectively. Receiver-operator characteristics analysis showed that the area under the curve of 0.89 (95% CI: 0.85-0.93) for CCS was superior to 0.69 (95% CI: 0.61-0.78) for exercise testing (P<0.0001). In conclusion, measurement of CCS is an appropriate initial screening test in a well-defined low-risk population with suspected CAD.

The objective of our study was the determination of the influence of the sequential and spiral acquisition modes on the concordance and deviation of the calcium score on 64-slice multi-detector computed tomography (MDCT) scanners in comparison to electron beam tomography (EBT) as the gold standard. Our methods and materials were an anthropomorphic cardio CT phantom with different calcium inserts scanned in sequential and spiral acquisition modes on three identical 64-slice MDCT scanners of manufacturer A and on three identical 64-slice MDCT scanners of manufacturer B and on an EBT system. Every scan was repeated 30 times with and 15 times without a small random variation in the phantom position for both sequential and spiral modes. Significant differences were observed between EBT and 64-slice MDCT data for all inserts, both acquisition modes, and both manufacturers of MDCT systems. High regression coefficients (0.90-0.98) were found between the EBT and 64-slice MDCT data for both scoring methods and both systems with high correlation coefficients (R2>0.94). System A showed more significant differences between spiral and sequential mode than system B. Almost no differences were observed in scanners of the same manufacturer for the Agatston score and no differences for the Volume score. The deviations of the Agatston and Volume scores showed regression dependencies approximately equal to the square root of the absolute score. The Agatston and Volume scores obtained with 64-slice MDCT imaging are highly correlated with EBT-obtained scores but are significantly underestimated (-10% to -2%) for both sequential and spiral acquisition modes. System B is more independent of acquisition mode to calcium score than system A. The Volume score shows no intramanufacturer dependency and its use is advocated versus the Agatston score. Using the same cut points for MDCT-based calcium scores as for EBT-based calcium scores can result in classifying individuals into a too low risk category. System information and scanprotocol is therefore needed for every calcium score procedure to ensure a correct clinical interpretation of the obtained calcium score results.

A model is presented that describes the image quality of coronary arteries with multidetector computer tomography. The results are discussed in the context of rotation time of the scanner, heart rate, and number of sectors used in the acquisition process. The blurring of the coronary arteries was calculated for heart rates between 50 and 100 bpm for rotation times of 420, 370, and 330 ms, and one-, two-, three-, and four-sector acquisition modes and irregular coronary artery movement is included. The model predicts optimal timing within the RR cycle of 45+/-3% (RCA), 44+/-4% and 74+/-6% (LCX), and 35+/-4% and 76+/-5% (LAD). The optimal timing shows a negative linear dependency on heart rate and increases with the number of sectors used. The RCA blurring decreases from 0.98 cm for 420 ms, one-sector mode to 0.27 cm for 330 ms, four-sector mode. The corresponding values are 0.81 cm and 0.29 cm for LCX and 0.42 cm and 0.17 cm for LAD. The number of sectors used in a multisector reconstruction and the timing within the cardiac cycle should be adjusted to the specific coronary artery that has to be imaged. Irregular coronary artery movement of 1.5 mm justifies the statement that no more than two sectors should be used in multisector acquisition processes in order to improve temporal resolution in cardiac MDCT.

Cardiac morbidity and mortality are closely related to cardiac volumes and global left ventricular (LV) function, expressed as left ventricular ejection fraction. Accurate assessment of these parameters is required for the prediction of prognosis in individual patients as well as in entire cohorts. The current standard of reference for left ventricular function is analysis by short-axis magnetic resonance imaging. In recent years, major extensive technological improvements have been achieved in computed tomography. The most marked development has been the introduction of the multidetector CT (MDCT), which has significantly improved temporal and spatial resolutions. In order to assess the current status of MDCT for analysis of LV function, the current available literature on this subject was reviewed. The data presented in this review indicate that the global left ventricular functional parameters measured by contemporary multi-detector row systems combined with adequate reconstruction algorithms and post-processing tools show a narrow diagnostic window and are interchangeable with those obtained by MRI.

Objective: Evaluation of the image quality of coronary artery stents at various heart rates using Multi Detector Computed Tomography (MDCT)., Methods: Nine different coronary stents were attached to a moving heart phantom and scanned using a 64-MDCT with a rotation time of 330 milliseconds (ms). The heart rate of the phantom was varied between 0 and 115 beats per minute (bpm). Two independent methods were used to investigate image quality. After reconstruction the average Houndsfield Unit (HU) value in the stent lumen was measured in the longitudinal and the cross-sectional plane. The stent images were then presented to two radiologists. The radiologists were asked to rank the images from good to bad based on lumen visibility and overall image quality. A second ranking was obtained using the CT density values. Finally two rankings were compared., Results: Compared to the value for air, the HU-values measured in the lumen increased by 50 to 700 HU. Average slope value in the longitudinal plane was 1.7 +/- 0.6 HU/bpm, and the average slope value in the cross-sectional plane was 1.7 +/- 0.8 HU/bpm. This shows increased attenuation with increasing heart rate and thus a negative correlation between image quality and heart rate in both planes for all stents. The ranking acquired from the radiologists resembled the measured results as they also showed a negative correlation between the two variables. Using the results of the CT density measurements an analysis was done on multi-segment reconstruction (MSR)., Conclusion: A negative correlation between the heart rate and image quality of coronary stents was found by two independent methods. MSR showed no benefit for image quality in this study.

Acquisition time plays a key role in the quality of cardiac multidetector computed tomography (MDCT) and is directly related to the rotation time of the scanner. The purpose of this study is to examine the influence of heart rate and a multisector reconstruction algorithm on the image quality of coronary arteries of an anthropomorphic adjustable moving heart phantom on an ECG-gated MDCT unit. The heart phantom and a coronary artery phantom were used on a MDCT unit with a rotation time of 500 ms. The movement of the heart was determined by analysis of the images taken at different phases. The results indicate that the movement of the coronary arteries on the heart phantom is comparable to that in a clinical setting. The influence of the heart rate on image quality and artifacts was determined by analysis of several heart rates between 40 and 80 bpm where the movement of the heart was synchronized using a retrospective ECG-gated acquisition protocol. The resulting reformatted volume rendering images of the moving heart and the coronary arteries were qualitatively compared as a result of the heart rate. The evaluation was performed on three independent series by two independent radiologists for the image quality of the coronary arteries and the presence of artifacts. The evaluation shows that at heart rates above 50 bpm the influence of motion artifacts in the coronary arteries becomes apparent. In addition the influence of a dedicated multisector reconstruction technique on image quality was determined. The results show that the image quality of the coronary arteries is not only related to the heart rate and that the influence of the multisector reconstruction technique becomes significant above 70 bpm. Therefore, this study proves that from the actual acquisition time per heart cycle one cannot determine an actual acquisition time, but only a mathematical acquisition time.