Search

Boundary conduction mode or critical conduction mode is characterized by an inductor current that operates in the boundary between continuous conduction modes (CCM) and discontinuous conduction modes, making the converter switching frequency dependent on the converter operating conditions. The advantage of this operation mode versus CCM is achieving zero current switching (ZCS) conditions for the converter rectifier, which makes it possible to use silicon diode rectifiers without having a penalty due to reverse recovery issues. Moreover, the main switch turn-on loss is decreased due to ZCS conditions and valley switching operation. However, the penalty is an increased current stress in the circuit and an increased main switch turn-off energy loss. Implementation of the synchronous rectifier in boundary conduction mode (BCM) converters makes it possible to achieve zero voltage switching (ZVS) conditions by extending the synchronous rectifier conduction time after zero current condition in the inductor. High power density and high-efficiency MHz implementations have already been demonstrated in the literature; however, none of the proposed solutions solves the controllability issues of the synchronous rectifier switch. This paper proposes and validates a ZVS self-regulating control method for BCM converters operating in the MHz switching frequency range. [ABSTRACT FROM AUTHOR]

High efficiency and low cost power converters for interfacing energy storage have become critical in renewable energy systems. In this paper, a fractional charging converter (FCC) is proposed to reduce power rating as well as cost of the dc–dc converter for hydrogen production by alkaline electrolyzer cells. The FCC configuration only processes the partial power resulting from the voltage difference between the source and the energy storage element.  Moreover, the converter employed in such configuration can be either isolated or non-isolated, which simplifies topology selection. An analysis and comparison of two dc–dc topologies using a high-frequency transformer based on component stress factor (CSF) is performed to determine the optimal solution for the evaluated application. Based on the results of the CSF analysis, and due to its capability of handling wide input voltage, the isolated full-bridge boost converter is designed, built, and tested. Experimental results prove the feasibility of the fractional charging configuration with a reduction of 80% of the power rating compared to the traditional interconnection, which implies a reduction in cost, weight, and an increase in efficiency. The converter's maximum voltage gain achieved is 25 and the highest measured system efficiency is 98.2%. [ABSTRACT FROM AUTHOR]

The increasing transistor power loss brought by the high switching frequency places a limit to the future high power density converter design. A review of resonant gate drivers is given in this paper to provide a vision for its future application. Various resonant gate driver topologies from the prior-art research is categorized and thoroughly compared in terms of the implementation frequency and the percentage gate driver loss reduction. Moreover, a case study of two representative resonant gate driver topologies is given. The conventional gate drive and two resonant gate drivers are implemented to driver Silicon MOSFETs and Gallium Nitride transistors, respectively. The feasibility and effectiveness of implementing resonant gate drivers in wide-bandgap semiconductor transistors is discussed according to a detailed comparison of loss decomposition. [ABSTRACT FROM AUTHOR]

This paper presents design of an isolated high-step-down dc–dc converter based on a class-DE power stage, operating at a 10-MHz switching frequency using enhancement-mode gallium nitride transistors. The converter operating principles are discussed, and the power stage design rated for 20 W is presented for a step down from 200–300 V input to 0–28 V output. Commercially available magnetic materials were explored and the high-frequency resonant inductor and transformer designs using a low-loss Fair-Rite type 67 material are presented. Finite-element simulations have been performed to estimate the parameters of magnetics at 10-MHz. Experimental results are presented at 12 W, 254 V input to 22 V output and 5 W, 254 V input to 14 V output on a laboratory prototype operating at 10-MHz. At 20 W, the experimental prototype achieved an efficiency of 85.2%. [ABSTRACT FROM AUTHOR]

It is well known that multilevel converters can offer significant benefits in terms of harmonic performance and reduced switching losses compared to their two-level counterparts. However, for lower voltage applications the neutral-point-clamped inverter suffers from relatively large semiconductor conduction losses because the output current always flows through two switching devices. In contrast, the T-type multilevel inverter has less conduction losses because only a single outer loop switching device is required to connect the converter output to the upper and lower dc buses, albeit at the expense of increased switching losses since these outer switches must now block the full dc link voltage. Silicon carbide (SiC) mosfet devices potentially offer substantial advantage in this context with their lower switching losses, but the benefit of replacing all switching devices in a T-type inverter with SiC mosfets is not so clear-cut. This paper now explores this issue by presenting a detailed comparison of the use of Si and SiC devices for a three-level T-type inverter operating in grid-tie applications. The study uses datasheet values, switching loss measurements, and calibrated heat sink thermal measurements to precisely compare semiconductor losses for these two alternatives for a T-type inverter operating at or near unity power factor. The results show that replacing only the dc bus connection switches with SiC devices significantly reduces the semiconductor losses, allowing either the converter power level or the switching frequency to be significantly increased for the same device losses. Hence, the use of SiC mosfets for T-type inverters can be seen to be an attractive and potentially cost-effective alternative, since only two switching devices per phase leg need to be upgraded. [ABSTRACT FROM AUTHOR]

This paper presents a comparative evaluation of the loss and thermal performance of two advanced three-level inverter topologies, namely the partial silicon carbide (SiC) T-Type and the Hybrid-neutral-point-clamped (NPC), both of which are aimed at reducing the high switching losses associated with a conventional Si T-Type inverter. The first solution directly replaces the 1200 V primary Si IGBT switches with lower loss 1200 V SiC MOSFETs. The second solution strategically adds 600 V CoolMos FET devices to the conventional Si T-Type inverter to reduce the primary commutation losses. Semiconductor loss models, experimentally verified on calibrated heat sinks, are used to show that both variations can significantly reduce the semiconductor losses compared with the Si T-Type inverter. The results show that both alternatives are attractive if high efficiencies and reduced thermal stress are major requirements for the converter design. [ABSTRACT FROM PUBLISHER]

This paper presents the design, modeling, and control of an isolated dc-dc three-port converter (TPC) based on an interleaved-boost full-bridge converter with pulsewidth modulation (PWM) and phase-shift control for hybrid renewable energy systems. In the proposed topology, the switches are driven by phase-shifted PWM signals, where both phase angle and duty cycle are the controlled variables. The power flow between the two inputs is controlled through the duty cycle, whereas the output voltage can be regulated effectively through the phase shift. The primary-side MOSFETs can achieve zero-voltage-switching (ZVS) operation without additional circuitry. Additionally, due to the ac output inductor, the secondary-side diodes can operate under zero-current-switching (ZCS) conditions. In this study, the operation principles of the converter are analyzed and the critical design considerations are discussed. The dynamic behavior of the proposed ac-inductor-based TPC is investigated by performing state-space modeling. Moreover, the derived mathematical models are validated by simulation and measurements. In order to verify the validity of the theoretical analysis, design, and power decoupling control scheme, a prototype is constructed and tested under the various modes, depending on the availability of the renewable energy source and the load consumption. The experimental results show that the two decoupled control variables achieve effective regulation of the power flow among the three ports. [ABSTRACT FROM PUBLISHER]

This paper deals with a thorough analysis of zero-voltage switching, especially for bidirectional inductorless piezoelectric transformer-based switch-mode power supplies with a half-bridge topology. Practically, obtaining zero-voltage switching for all of the switches in a bidirectional piezoelectric power converter is a difficult task. However, the analysis in this paper will be convenient for overcoming this challenge. The analysis defines the zero-voltage region indicating the operating points whether or not soft switching can be met over the switching frequency and load range. For the first time, a comprehensive analysis is provided, which can be used as a design guideline for applying control techniques in order to drive switches in piezoelectric transformer-based converters. This study further conveys the proposed method to the region where all the switches can obtain soft switching. Moreover, the analysis can be applied to other types of resonant converters with or without piezoelectric transformers. Experimental and simulation results are provided verifying the performed analysis. [ABSTRACT FROM AUTHOR]

Power electronics is a fast-developing technology within the electrical engineering field. This paper presents the results and experiences gained from applying design-oriented project-based learning to switch-mode power supply design in a power electronics course at the Technical University of Denmark (DTU). Project-based learning (PBL) is known to be a motivating problem-centered teaching method that not only places students at the core of teaching and learning activities but also gives them the ability to transfer their acquired scientific knowledge into industrial practice. Students choose a specification to implement from various power converter application projects, such as a fuel cell power conditioning converter, a light-emitting diode (LED) driver or a battery charger. The students select the topology, design magnetic components, calculate input/output filters and design closed-loop controllers necessary to fulfill the requirements listed in the chosen specification and thus meet the project's goals. This paper presents the course teaching plan and teaching methods, assessment method and student feedback. [ABSTRACT FROM PUBLISHER]

Light-emitting diode (LED) illumination is getting more and more common; as LED’s performance is rising, the price is falling and is getting competitive. Some of the challenges of ac mains supplied illumination are the requirement of power factor correction (PFC) and the competitiveness of a low priced market. In this paper, a new forward conduction mode (FCM) control method for piezoelectric transformer (PT)-based power converters is proposed. A PT-based LED drive facilitating passive PFC is developed, utilizing and validating the FCM control method. The drive utilizes an inductorless half-bridge topology and for circuit minimization and simplicity it has no load regulation and has a 100-Hz output modulation. The proposed FCM control method ensures that the PT is operated at its optimal operation frequency, which ensures soft-switching operation and a constant gain. As a result a 6.5-W PT-based PFC LED drive has been developed, supplied from 230-V 50-Hz ac mains, achieving a power factor of 0.96. [ABSTRACT FROM AUTHOR]