Search

Although LLC converters are attractive in industrial applications due to its advantages of soft switching, high efficiency, and simple control, in wide voltage gain range applications, large switching frequency operating range is required, which may cause the loss of soft switching operation and existence of control instability issue. In this article, a novel LLC converter with two LLC resonant tanks is proposed. The proposed converter has three operation modes, namely, dual full-bridge operation mode, full-bridge operation mode, and half-bridge operation mode, which can cover the high voltage gain range, medium voltage gain range, and low voltage gain range operations, respectively. The operational principles of the proposed converter are presented, and brief design considerations are discussed. A 250 W experimental prototype with six times input voltage range (50–300 V) was built to validate the theoretical analysis of the proposed converter. Comparisons among different LLC topologies for wide voltage gain range applications are made. [ABSTRACT FROM AUTHOR]

Hold-up time operation is a crucial requirement for distributed power systems and server power supplies. LLC resonant converter is widely used in these applications due to its high efficiency and power density characteristics. Conventional pulse frequency modulation (PFM)-controlled inductor-inductor-capacitor (LLC) resonant converter requires a wide switching frequency operation range to satisfy the hold-up requirement. In this article, a novel control scheme is proposed for stacked structure LLC resonant converter. During the normal operation, the frequency doubler modulation strategy is adopted to reduce the switching loss and driving loss, and the output is regulated by PFM. During the hold-up time operation, the pulsewidth modulation is adopted to increase the system voltage gain, where the switching frequency is fixed during this operation stage. For the proposed converter, the resonant tank parameters are designed at the nominal operation point, and the only design consideration for the magnetizing inductor is the zero-voltage switching for primary switches. Therefore, compared with PFM-LLC, both the switching frequency operating range and the circulating current are reduced, and high efficiency feature is obtained. Finally, a 100-W experimental prototype with input voltage range of 160–340 V was built to validate the advantages of the proposed converter. [ABSTRACT FROM AUTHOR]

The cascaded H-bridge (CHB) inverter is one of the most attractive multilevel topologies for renewable energy applications. Due to the fact that CHB inverters employ a large number of components, they suffer from a higher probability of fault, which reduces the system reliability. A fault-tolerant operation for a CHB inverter is described in this article. New features ensure reliable and robust operation of the converter in the event of a fault. The proposed strategy uses an additional cross-coupled CHB (X-CHB) unit in companion with the existing CHB units to support the output voltage and ensure continuity of operation in the event of an open/short-circuit fault. The operation of the proposed X-CHB inverter is described in detail. Simulation and experimental verification of the proposed concept are demonstrated using a seven-level CHB. Both simulation and experimental results confirm the fault-tolerant operation of the X-CHB for a battery energy storage system in case of switch faults. [ABSTRACT FROM AUTHOR]

In order to realize power flow control among photovoltaic (PV) panel port, battery port, and load port in the distributed photovoltaic power generation system, integrated three-port dc–dc converters (TPCs) are widely adopted. The objective of this article is to provide a comprehensive, comparative, and insightful analysis and overview of these TPCs. First, based on the power transmission and control requirements of the system, five topological structures of three-port dc–dc conversion system (TPCS) composed of two or three two-port dc–dc converters are presented. And the five structures are comparatively analyzed. Second, based on these topological structures, and combing with the basic two-port dc–dc converters, three groups of typical TPCs with different galvanic isolation requirements are derived, respectively, by sharing switches, combining branches, etc., And comprehensive analysis, comparisons, and reviews of these TPCs with different structures of each isolation type are presented with tables and figures. Finally, the comparison results of the three isolation groups are summarized, which leads to a guidance for the selection of TPCs in different applications, and then some suggestions for the future research on TPCs are given. [ABSTRACT FROM AUTHOR]

In this paper, a dual half-bridge LLC resonant converter with magnetic control is proposed for the battery charger application. The primary switches are shared by two LLC resonant networks, and their outputs are connected in series. One of the LLC resonant converters is designed to operate at the series resonant frequency, which is also the highest efficiency operating point, and the constant output voltage characteristic is achieved at this operating point. The second LLC resonant converter adopts magnetic control to regulate the total output current and voltage during both constant current charge mode and constant voltage charge mode. Meanwhile, the function decoupling idea is adopted to further improve the system efficiency. The significant amount of the power is handled by the LLC resonant converter operating at the series resonant frequency, whereas the second LLC resonant converter fulfills the responsibility to achieve closed-loop control. By carefully designing the resonant networks, the zero-voltage switching for primary switches and zero-current switching for secondary diodes can be achieved for whole operation range. A 320-W experimental prototype is built to verify the theoretical analysis, and the maximum efficiency is measured about 95.5%. [ABSTRACT FROM AUTHOR]

High step-up boost converters with coupled inductor have attracted much attention in the fuel cell or photovoltaic grid-connected generation system, however, there are few literatures elaborated on the construction ideas and derivation methods of them. Accordingly, in order to obtain a clear roadmap on the derivation and inner connection of these converters, a comprehensive review and analysis are presented in this paper. First, the basic boost converter with coupled inductor is regarded as the basic topology, and its merits and demerits are analyzed in detail. Then, in order to address these demerits, various step-up techniques are introduced, such as the rectifier circuit, the active-clamped circuit, the multi-winding coupled inductor, and the voltage doubler rectifier; and numerous new topologies are continuously proposed by combinations and equivalent simplifications. In addition to a detailed synthesis of each topology, a comparative and quantitative analysis among some important converters is presented, and the optimal one is chosen to build a 250 W prototype. Finally, based on comparisons and analysis, the main characteristics and inner connections of these high step-up boost converters with coupled inductor are identified and clarified. [ABSTRACT FROM AUTHOR]