Search

The high fraction of runaway current conversion following disruptions has an important effect on the first wall for next-generation tokamaks. Because of the potentially severe consequences of a large full current runaway beam on the first wall in an unmitigated disruption, runaway suppression is given a high priority. The behavior of runaway currents both in spontaneous disruptions and in D2 massive gas injection (MGI) shutdown experiments is investigated in the KSTAR tokamak. The experiments in KSTAR show that the toroidal magnetic field threshold, BT > 2 T, for runaway generation is not absolute. A high fraction of runaway current conversion following spontaneous disruptions is observed at a much lower toroidal magnetic field of BT = 1.3 T. A dedicated fast valve for high-pressure gas injection with 39.7 bar is developed for the study of disruptions. A study of runaway current parameters shows that the conversion efficiency of pre-disruptive plasma currents into runaway current can reach over 80% both in spontaneous disruptions and in D2 MGI shutdown experiments in KSTAR. [ABSTRACT FROM AUTHOR]

The Korea Superconducting Tokamak Advanced Research (KSTAR) device is aimed at advanced tokamak (AT) research. Three years have passed since it achieved its first plasma in 2008. Because it is a superconducting machine and is working toward AT research, it has unique features in terms of the machine engineering and operation. The toroidal field (TF) magnet coils are made of \Nb3\Sn, which provide high TFs up to 3.5 T, and have been fully tested. The poloidal field (PF) magnet coils, consisting of both \Nb3\Sn and NbTi, which have a maximum current of 25 kA in their design, were tested up to 15 kA. A thermal hydraulic analysis is being conducted for PF magnet coil operation. All plasma-facing components (PFCs) are equipped with water cooled graphite tiles and have the capability of being baked up to 350 ^\circ\C. A startup scenario, which considered both the effect of the ferromagnetic material in the cable in conduit conductor jacket of the magnet coils as well as a nonferromagnetic up-down asymmetry in the cryostat structure, was developed and demonstrated its effectiveness by the last two year's reliable operations. Passive stabilizers and in-vessel control coils (IVCCs) are key components to realize AT operation in KSTAR. The segmented IVCC coils were connected to form circular coils for internal vertical control in 2010, and diverted plasmas with high elongation (\kappa \sim 1.8,\ \delta > 0.6) were achieved. A neutral beam injection (NBI) system was developed aiming at 2 MW, 300 s per ion source which meets the long-pulse requirement of KSTAR. An NBI ion source with a power of 1.7 MW at 100 kV has been commissioned for 10 s. Finally, ELMy H-modes were successfully produced with 1.3-MW NBI power at a plasma current of 0.6 MA in the 2010 campaign. The first H-mode discharge (#4200) in KSTAR was achieved one year earlier than officially planned and was done at BT = 2\ \T with Ip = 0.6\ \MA in a well-balanced double null configuration after boronization on the PFC. Successful operations in the early days of KSTAR including H-mode experiments revealed the capability of advanced and steady-state operation which is essential for the international thermonuclear experimental reactor (ITER) and future fusion reactors. [ABSTRACT FROM PUBLISHER]

To detect quenches in the Poloidal Field (PF) magnet system is more difficult than the Toroidal Field (TF) magnet system due to excessively high inductive voltages generated by PF pulse-currents and plasma currents. According to reference scenarios being considered so far, the maximum voltage across the PF coils is inductively generated up to about 3.5 kV during the start of plasma (SoP) stage in a very short time period. The voltage measured by compensation of the inductive voltage should be below a certain level which is called as the quench voltage threshold. However, the compensated voltage might be higher than the threshold even with the well-designed compensation schemes. Accordingly, the quench voltage threshold and the quench protection delay time should be properly determined for the quench detection not to take a false action which could cause the fast energy discharge. From the quench simulation using the calculation of hot spot temperature and the resistive voltage growth as a function of time, the proper values of the quench detection parameters of the PF magnet system were derived for the maximum hot temperature rise to be limited within 150 K. [ABSTRACT FROM AUTHOR]

In the Korea Superconducting Tokamak Advanced Research(KSTAR) device, the Toroidal Field (TF) coils were manufactured with Nb3Sn, and the bus lines with NbTi, and all the coils are cooled by supercritical helium. During the first campaign, the TF coils were operated with a steady state current of 15 kA. In case of a quench the conductor is being developed due to an unexpected effect on the superconducting strands, the current should be discharged into an external dump resistor for protection of the magnet. The development or recovery of the quench is related to the protection triggering delay time and the quench voltage. The thermo-hydraulic phenomena were simulated by the GANDALF code and the initial quench propagation condition was found from the minimum quench energy and the initial quench zone. In this paper, we determined the quench voltage level and trigger time by analysis of temperature, voltage, and pressure growth, in the magnet and bus lines, with triggering delays of t = 2 s, 3 s, 4 s, and 5 s, by analysing the effects of a temperature and voltage growth of the magnet and bus lines. [ABSTRACT FROM AUTHOR]

To protect the KSTAR (Korea Superconducting Tokamak Advanced Research) superconducting coils against a quench, the quench detection system based on voltage measurement was fabricated. It used a detect/dump scheme which detects the presence of non-recovering normal zones and activates a dump circuit that transfers most of the stored energy into a dump resistor. Even though it is desirable to discharge the coil energy as fast as possible after quench detection, a time delay between the quench detection and the complete dump circuit actuation will be necessary in order that the quench voltage is to be distinguished from various noises. The quench threshold voltage and the delay time should be set before operation for quench voltage detection so that the maximum hot-spot temperature could be limited to 150 K. This paper describes the hardware techniques to prevent the malfunction of the quench detection due to voltage noises arising from the KSTAR operating scenarios. During the first operation of the KSTAR machine, the inductive voltages and other voltage noises were measured and effectively compensated below voltage thresholds. A quench did not occur and the quench detection system was well operated without any false activation. [ABSTRACT FROM AUTHOR]

KSTAR (Korea Superconducting Tokamak Advanced Research) superconducting magnet consists of a CICC (Cable-In-Conduit Conductor) and is cooled down less than 5 K using supercritical helium. The length of CICC is 610 m for TF coil and maximum about 2,500 m for PF coil respectively, especially the cooling channel is about maximum 300 m in PF coil because of continuous winding scheme. There are many cooling channels in KSTAR coils especially 84 channels in TF magnet system and 100 channels in PF magnet system. Flow imbalance affects cool down of magnet and leads to a difficulty of flow control. The pressure drop between CICC terminals has a close relationship with CICC hydraulic characteristic, helium refrigerator's performance and efficiency. The friction factor which is a representative parameter can be obtained under cryogenic operation condition. We attempt to find out the friction factor of KSTAR CS and PF CICC according to the test result of KSTAR CSMC (Central Solenoid Model Coil) 2nd campaign and compare the results with previous tests. The hydraulic characteristics of KSTAR superconducting magnet system like mass flow distribution, friction factor in conductor, pressure drop and etc during CSMC test and initial commissioning of KSTAR are presented. We can confirm the KSTAR CICC's unique hydraulic behavior in states of cool down and current charging period. Also, we expect that measured data will help to operate KSTAR and be a reference for thermo-hydraulic simulation. [ABSTRACT FROM AUTHOR]

An in-situ measurement of the magnetic field generated by the assembled superconducting magnet coils was held by using precision Hall sensors during the commissioning of the Korea Superconducting Tokamak Advanced Research (KSTAR) device. This was done in order to investigate the magnetic influence of Incoloy 908, which is the jacket material for the cable-in-conduit conductors (CICCs) of the Nb3 Sn coils. After the PF coils were discharged from 1 kA the vertical remanent field at the plasma center was more than 10 G, while the TF coils were not energized. The vertical magnetic field generated by the PF coils had a discrepancy of up to 50 G between measurement and the calculation assuming no magnetic influence of Incoloy 908. Thus, non-negligible ferromagnetism was identified and attributed to Incoloy 908. In contrast, most of the hysteresis observed in the magnetic measurements was eliminated when the Incoloy 908 of the TF windings was saturated by the TF coil charging. [ABSTRACT FROM AUTHOR]

To achieve the first plasma of the Korea superconducting tokamak advanced research (KSTAR), the KSTAR superconducting coils were tested in advance. As they should operate in excessively low temperature of 4.5 K and high magnetic field environment of 7.5 T, it is crucial to monitor the cryogenic and the structural behaviors of KSTAR device during the commissioning period including a cool-down. The temperatures of the KSTAR toroidal field (TF) coil and the poloidal field (PF) coils were measured during the entire operating period. The mechanical stresses on the TF and PF structures were continuously monitored to check if they go beyond the limiting value calculated through the simulation. The alignment of the KSTAR device was checked by using displacement sensors. The TF coils were successfully supplied with 15 kA DC current for 8 hours, and the maximum 5 kA/s current variation of the PF coils were tested. For the main experiment, the interlock test of the quench detection system for the KSTAR coils was carried out at reduced currents of 1 kA. From these results the quench protection circuit, and the current-flow of the KSTAR superconducting coils proved to be well performed for the first plasma operation. [ABSTRACT FROM AUTHOR]

The KSTAR Central Solenoid Model Coils (CSMC), which are in the form of split coils with same dimension, have been tested. The CSMC were successfully charged up to 20 kA and down to zero with different ramp rates. Various pulse waveforms were applied to the CSMC to analyse the AC-loss characteristics of the coils. The measurement method was a gas-flow calorimetry. In this work, two types of waveforms, the DC-biased sinusoidal wave (Idc = 2, 4 kA; ΔIac = 1 kA; ƒ = 0.08 ∼ 0.67 Hz) and a single triangular pulse (Imax = 6 ∼ 10 kA; dI/dt = 0.5 ∼ 2 kA/s), are selected and analysed. From the measured data at the one outlet where helium channel 3 and 4 are merged, the AC loss parameters, related with the hysteresis loss and the coupling loss, are calculated. The B-field strength differs depending on the position within the cooling channels. The spatial field variation and the ramp rate were 0.048∼ 1.9T and 8.1∼ 71 mT/s for the DC-biased sinusoidal waves, while 0.29∼ 4.3 T and 0.024∼ 0.86 T/s for the triangular pulses. The measured AC losses are compared with estimated values and the behavior agrees well. The coupling time constant (nτ) varies with the field strength. In case of the triangular pulses, nτ increases by increasing the field amplitude and the maximum value of nτ is 41 ms with Imax = 10 kA. [ABSTRACT FROM AUTHOR]