Search

As applications move to the edge, efficiency in computing power and power/energy consumption is required. Heterogeneous computing promises to meet these requirements through application-specific hardware accelerators. Runtime adaptivity might be of paramount importance to realize the potential of hardware specialization, but further study is required on workload retargeting and offloading to reconfigurable hardware. This article presents our framework for the exploration of both offloading and hardware generation techniques. The framework is currently able to process instruction sequences from MicroBlaze, ARMv8, and riscv32imaf binaries, and to represent them as Control and Dataflow Graphs for transformation to implementations of hardware modules. We illustrate the framework's capabilities for identifying binary sequences for hardware translation with a set of 13 benchmarks. [ABSTRACT FROM AUTHOR]

Summary: This paper presents an automatic procedure for the design and optimization of switched‐capacitor (SC) filters, including the automatic sizing of transistors in the amplifiers and switches. The optimization procedure is based on genetic algorithms (GAs) where the circuit's fitness is first computed using equations describing the filter's transfer function and then using transient simulations. These equations are obtained using a fast numerical methodology that takes into consideration the electrical behavior of all components in the circuit. The poles and zeros of the SC filter's transfer function are computed using a system of differential equations, obtained from the inspection of the circuit. This system describes the filter's behavior for all switch combinations, including the non‐ideal effects of the transistors in the switches and amplifiers. Due to the low computational effort and accuracy of this methodology, it is possible to use a large population in the GA. After finding a solution through equations, the more computationally intensive SPICE transient simulations are used to fine‐tune the solution, with a much smaller population in the GA. Taking advantage of the equations' low computational load and accuracy, process, voltage, temperature (PVT) corners and mismatch errors optimizations are also performed, allowing the chromosomes fitness to be calculated taking into consideration multiple cases, thus resulting in a low sensitivity design. [ABSTRACT FROM AUTHOR]

This brief presents a programmable second-order bandpass switched-capacitor filter implemented for an Internet-of-Things water management sensor node. The filter circuit, which is based on the Sallen-Key topology, is implemented using a low-gain amplifier (<2), avoiding designing high-gain high-bandwidth opamps, which can be difficult to design in advanced CMOS technologies, due to the reduction of the supply voltage and of the intrinsic gain of the transistors. Without the high gain, the circuit becomes sensitive to the effects of parasitic capacitances, which have to be minimized and compensated during the design process. The filter circuit was designed and fabricated in a 130-nm CMOS technology, using a supply voltage of only 0.9 V, to reduce the power dissipation, and a clock frequency of 1 MHz. Measurement results show that the filter’s central frequency can be tuned between 3.9 kHz and 7.1 kHz, the gain between −6.4 dB and 12.6 dB, and the quality factor between 0.9 and 6.9. In the default digital control code of the capacitor banks, the circuit has an IM3 of −66.5 dB. The total power consumption is 257 ${\boldsymbol \mu }\text{W}$. [ABSTRACT FROM AUTHOR]

The two projects presented in this paper can be used either as two separate assignments in two different semesters or as a final assignment for undergraduate students of electrical engineering. They have two main objectives: first, to teach basic electronic circuit design concepts and, second, to motivate the students to learn more about analog circuit design. The two projects are: 1) the design of an audio power amplifier, and 2) the design of an amplitude-modulated optical link with a pulsed light-emitting diode (LED) at the emitter and a photodiode and a transimpedance amplifier at the receiver. An audio signal is used to modulate the oscillator that drives the LED, and the receiver demodulates this signal to produce an audio signal (music, for example) that can be sent to a loudspeaker. The intent of this optical communication system was to allow students to design and build various electronic circuits that have an overall objective and a clear practical application. Students are motivated by using this system to transmit, receive, and listen to their own music. [ABSTRACT FROM PUBLISHER]