Search

In this work, we present a systematic study of the effect of the stoichiometry of BaTiO3 (BTO) films grown on the Ge(001) substrate by molecular-beam-epitaxy using different characterization methods relying on beam diffraction, including reflection high-energy electron diffraction (RHEED), X-ray diffraction (XRD), and selected-area electron diffraction in transmission electron microscopy. Surprisingly, over a wide range of [Ba]/[Ti] ratios, as measured by the Rutherford backscattering spectrometry, all the BTO layers exhibit the same epitaxial relationship h100iBTO(001)// 〈110〉Ge(001) with the substrate, describing a 45° lattice rotation of the BTO lattice with respect to the Ge lattice. However, varying the [Ba]/[Ti] ratio does change the diffraction behavior. From RHEED patterns, we can derive that excessive [Ba] and [Ti] generate twinning planes and a rougher surface in the non-stoichiometric BTO layers. XRD allows us to follow the evolution of the lattice constants as a function of the [Ba]/[Ti] ratio, providing an option for tuning the tetragonality of the BTO layer. In addition, we found that the intensity ratio of the 3 lowest-order Bragg peaks I(001)/ I(002), I(101)/I(002), and I(111)/I(002) derived from ω-2θ scans characteristically depend on the BTO stoichiometry. To explain the relation between observed diffraction patterns and the stoichiometry of the BTO films, we propose a model based on diffraction theory explaining how excess [Ba] or [Ti] in the layer influences the diffraction response. [ABSTRACT FROM AUTHOR]

The three-dimensional (3D) distribution of carbon nanotubes (CNTs) grown inside semiconductor contact holes is studied by electron tomography. The use of a specialized tomography holder results in an angular tilt range of ±90°, which means that the so-called "missing wedge" is absent. The transmission electron microscopy (TEM) sample for this purpose consists of a micropillar that is prepared by a dedicated procedure using the focused ion beam (FIB) but keeping the CNTs intact. The 3D results are combined with energy dispersive X-ray spectroscopy (EDS) to study the relation between the CNTs and the catalyst particles used during their growth. The reconstruction, based on the full range of tilt angles, is compared with a reconstruction where a missing wedge is present. This clearly illustates that the missing wedge will lead to an unreliable interpretation and will limit quantitative studies. [ABSTRACT FROM AUTHOR]

The impact of the Ge fraction ( x), on the leakage current of recessed Si1− x Ge x p+-n source/drain junctions has been investigated, for a fixed recess depth of 70 nm. It is found that both the bulk and the peripheral leakage current density increase approximately exponentially with increasing Ge content in the range 10–30%. Roughly speaking, the leakage current density increases one decade for every 5% increase in Ge. In case of the bulk leakage current density, this enhancement is shown to be related to the increase in extended defects penetrating the depletion region in the n-type silicon substrate. Transmission Electron Microscopy demonstrates a higher density of dislocations at the epitaxial interface for a higher Ge fraction, which are most likely generated by strain relaxation, induced by the implantation and activation of B in the p+ S/D regions. [ABSTRACT FROM AUTHOR]

Dark-field holography, a new transmission electron microscopy technique for mapping strain distributions at the nanoscale, is used to characterize strained-silicon n-type transistors with a channel width of 65 nm. The strain in the channel region, which enhances electron mobilities, is engineered by recessed Si0.99C0.01 source and drain stressors. The strain distribution is measured across an array of five transistors over a total area of 1.6 μm wide. The longitudinal tensile strain reaches a maximum of 0.58%±0.02% under the gate oxide. Theoretical strain maps obtained by finite element method agree well with the experimental results. [ABSTRACT FROM AUTHOR]

The density of hafnium oxide films grown by atomic layer deposition for high-κ gate dielectric applications was investigated for films with thickness in the nanometer range. The density, measured by combining the film thickness from transmission electron microscopy with the amount of hafnium deposited from Rutherford backscattering, decreased with decreasing film thickness. The dielectric constant of hafnium oxide remained constant with decreasing film thickness, however. The main reason for the decrease in the measured density seemed not to be a decrease in the inherent material density. Instead, the relative importance of interface roughness in the density measurement increased with decreasing film thickness. [ABSTRACT FROM AUTHOR]

Ultrathin lanthanide (Nd, Pr, Eu, Sm) oxide films with functional dielectric properties down to 3.3 nm thickness were deposited by aqueous chemical solution deposition (CSD) onto hydrophilic SiO2/Si substrates. Precursor solutions were prepared from the oxides via an intermediate, solid Ln(III)citrate. A film heat treatment scheme was derived from thermogravimetric analysis of the precursor gels, showing complete decomposition by 600 °C. Crystalline phase formation in the films depended on the lanthanide, annealing temperature, and citric acid content in the precursor. Through variation of the precursor concentration and number of deposited layers, thickness series of uniform films were obtained down to ~3 nm. The film uniformity was demonstrated both by atomic force microscopy and cross-section transmission electron microscopy. The lanthanide oxide films possessed good dielectric properties. It was concluded that aqueous CSD allows deposition of uniform ultrathin films and may be useful for the evaluation of new high-k candidate materials. [ABSTRACT FROM AUTHOR]

The reaction of a Ti (8 nm) capped Co film (15 nm) with a Si[sub 3]N[sub 4] layer (150 nm) is studied after rapid thermal annealing at 660 °C for 120 s in a N[sub 2] ambient. X-ray photoelectron spectroscopy, transmission electron microscopy, electron energy-loss spectroscopy, and Auger electron spectroscopy are used to study the reaction products. Combining the results of the different analyses yields a layer stack consisting of: TiO[sub 2]/TiO/unreacted Co/(Ti,Co)[sub 2]N/Co[sub 2]Si, followed by amorphous Si[sub 3]N[sub 4]. The reaction mechanisms are discussed. Conclusions concerning the risk for degradation of nitride spacers in advanced devices are drawn. © 2000 American Institute of Physics. [ABSTRACT FROM AUTHOR]

Abstract: We propose an empirical law correlating the average number of walls and the average diameter in a population of multi-wall carbon nanotubes grown by catalytic chemical vapor deposition. The relationship and its dispersion are derived from the statistical analysis of a database of TEM images of nanotubes collected from more than 60 publications in literature and from our group in the last years. Considering the nanotubes were grown from independent sources in a variety of conditions and tools, it has general validity. The relationship may find applicability in a wide range of fields as it provides a simple model to quickly estimate the number of walls most likely present in a population of nanotubes from only the measure of their average diameter. [Copyright &y& Elsevier]

Abstract: We report on the synthesis of Cu3Ge films by exposing Cu films to germane (GeH4). The process window was established by investigating the influence of the GeH4 partial pressure, the soak temperature, and the soak time on Cu films of different thickness. It is shown that short exposures of germane led to Cu-rich germanides, while an excessive GeH4 supply resulted in a Cu3Ge/Ge mixed phase. The germanidation reaction was found to be selective and required the prior removal of the native Cu oxide by in situ plasma cleaning. X-ray diffraction and transmission electron microscopy showed that the Cu3Ge films were crystalline as deposited in the orthorhombic phase and were textured. The films were homogenous in composition. Thin films consisted of Cu3Ge islands connected by a thin wetting layer. Fully continuous layers were however found for larger film thicknesses. The continuity of the Cu3Ge film was also found to be influenced by the pseudosubstrate: the films were more continuous on TaN/Ta than on SiO2. The electric properties of the Cu3Ge films on both TaN/Ta and SiO2 pseudosubstrates are presented and compared. [Copyright &y& Elsevier]

Abstract: A powerful method to study carbon nanotubes (CNTs) grown in patterned substrates for potential interconnects applications is transmission electron microscopy (TEM). However, high-quality TEM samples are necessary for such a study. Here, TEM specimen preparation by focused ion beam (FIB) has been used to obtain lamellae of patterned samples containing CNTs grown inside contact holes. A dual-cap Pt protection layer and an extensive 5kV cleaning procedure are applied in order to preserve the CNTs and avoid deterioration during milling. TEM results show that the inner shell structure of the carbon nanotubes has been preserved, which proves that focused ion beam is a useful technique to prepare TEM samples of CNT interconnects. [Copyright &y& Elsevier]