Search

Highlights • A measurement system for the internal and external preforms temperature profiles has been developed. • Cheap IR detectors can effectively be used for the purpose. • Measurement uncertainties lower than 2 °C can be achieved if the material emissivity is known. • Using average PET emissivity leads to uncertainties up to 6 °C. • The system allows implementing an in line closed loop temperature control system. Abstract This paper describes a system for the measurement of the internal and external temperature profiles of PET preforms used in the Injection Stretch Blow Moulding (ISBM) process. Many works in literature highlighted the importance of these quantities to improve the production quality of PET bottles, but none addressed the development of a measuring system suitable for this scope. A measuring system based on two thermopiles for the identification of the internal temperature profile and a thermal camera for the measurement of the external one has been designed. The adopted sensors were individually calibrated and the uncertainty budget, accounting for both instrumental uncertainties and the effect of multiple reflections, was derived. A prototype of the measuring system was tested on an industrial ISBM machine. The dependence of the preforms temperature profile on the settings of the ISBM machine was investigated. Results evidenced that the minimum variations of the machine settings induced temperature differences significantly larger than the measurement uncertainty, thus proving the effectiveness of the proposed system. [ABSTRACT FROM AUTHOR]

This paper describes a method for the comparison of the cooling capability of over-the-counter devices for skin tags removal. The comparison is performed by measuring the heat flux produced by the gas identified assessing the temperature difference across an element with a known thermal resistance; the temperature reached at the interface between the device and the heat-flux meter is also analyzed, although it is different from that of the skin during the treatment. The measurement accuracy has been experimentally evaluated and, with a confidence interval of 95%, is better than 6% for heat-flux measurements and lower than 0.3 °C for temperature measurements. The instrument allowed comparing the thermal efficiency of 19 dimethyl ether and propane devices of different types (dispenser, spray, and foam). Results are by far more reliable than those obtained with tests performed on subjects, where the intrinsic skin thermal properties variability prevents from assessing differences smaller than 30%. [ABSTRACT FROM PUBLISHER]

Abstract: Patch near-field acoustic holography (NAH) coupled with an array of sound intensity probes allows separating the sound field incident on a surface from the one radiated by the surface itself. Although the measurement principle has been successfully used to separate the noise source contribution from disturbing sources and/or noise reflections, the method accuracy has not been investigated in the literature. We describe the results of experiments meant to evaluate the uncertainty in the identification of noise radiated by vibrating panels with different absorption characteristics in presence of an incident acoustic radiation using the statistically optimized near-field acoustic holography. Measurement errors were evaluated through tests performed in controlled acoustic conditions. Results evidenced that the measurement uncertainty depends on the accuracy of the microphone array positioning and on the incident sound field. These conclusions were in agreement with the results obtained by simulations in the phase of instrument optimization. [Copyright &y& Elsevier]

Plantar pressure measurements provide useful information to diagnose a diverse range of foot disorders; unfortunately, the commercially available measurement systems are undesirably sensitive to several disturbances, but this aspect is mostly neglected in the literature. This paper describes the results of an experimental campaign aiming at the identification of pressure measuring system metrological performances, at system modeling, and at the implementation of correction procedures. The sensor model was implemented using the results of static and dynamic tests performed on a pedar-X plantar pressure measurement system. The static calibration was performed by analyzing the effect of temperature, single sensor coverage area, local curvature, tangential forces, long-term stability (creep), and sensor crosstalk on the system performances. The dynamic calibration was performed on an electrodynamic shaker, identifying the single sensor frequency response function and the hysteresis under different average loads. The dynamic sensor model is based on the Kelvin–Voigt model, which is representative of the viscoelastic behavior of the material. The model allowed us to compensate both the creep (i.e., the behavior under static loads) and the nonunitary frequency response function. A deconvolution-based algorithm has been proposed to compensate the sensor crosstalk effects, although its implementation requires additional investigations. Experimental results of bobbing and gait tests showed that, with the adoption of the proposed compensation algorithms, the force and center of pressure errors could be reduced by more than 50\% of their initial values. [ABSTRACT FROM PUBLISHER]

This paper describes a method that allows accuracy and bandwidth enhancements in 3-D sound intensity measurements. Commercial 3-D probes are usually set up with three mutually perpendicular 1-D p-p probes and, thus, arranged with six microphones; although sound intensity can be calculated with 15 independent pairs of transducers, only the three "primary" pairs that are aligned with the coordinate system axes. The other 12 "secondary" pairs consist of mutually perpendicular microphones, which are placed at a distance that is √2 times shorter than the primary one. The main idea of the proposed method is to average the intensity that is measured on primary and secondary pairs. This leads to a larger bandwidth, thanks to the shorter separating distance between secondary pairs. The intrinsic p-p method high- frequency sensitivity loss is partially recovered, starting from the theoretical plane wave expression. Measurements of different axes are weighted with coefficients that are computed by optimizing the measurement uncertainty. Errors that are due to the metrological characteristics of the transducers and the effects of environmental conditions are compensated. Experimental results showed that a p-p probe arranged with half-inch microphones that are placed at a distance of 50 mm allows reliable measurements up to 2.5 kHz, whereas a commercial probe bandwidth with the same configuration is usually 1250 Hz. [ABSTRACT FROM AUTHOR]

• The system is compatible with very low environmental pressure, even high vacuum. • The amplification of noise due to the required numerical derivative is avoided thanks to the data interpolation, • The uncertainty has been analyzed and the critical sources identified. • Way for uncertainty reduction have been identified along with limitation. • The system has been successfully used. This paper presents the design and validation of a volume flow measurement system developed to measure volume flowrate of gas at pressures below 1 kPa. The system had to be developed because a suitable commercial transducer was not available for the unusual working environment, where outgassing and sublimation phenomena become relevant for many materials and the rarefied atmosphere changes dramatically its heat and mass exchange parameters. The development of a low-pressure compatible measurement system comes from the need of measuring the flow rate of a rotary vane pump working under an environmental absolute pressure in the range between 600 and 1000 Pa, mostly composed by CO 2 i.e. the average condition of the Martian atmosphere at the surface. The pump will be a key component of the MicroMED particle analyzer, an instrument of the ExoMars 2020 ESA-Roscosmos mission payload. The measurement system is based on a control volume, made by a stainless-steel bellow, which has been designed accounting for the environmental requirements and the expected flow rate. The measurement system has been calibrated at ambient condition and tests in low-pressure have been performed to validate the measurement system and to derive the flow rate characteristics of a pump mock-up at different environmental pressures. [ABSTRACT FROM AUTHOR]