Search

Air entrainment in cement-based materials is believed to be affected by low air pressure (AP) which is the atmospheric characteristic in high plateaus, and thus the rheology may be affected. This paper attempts to study rheology and air entrainment of fresh Portland cement mortar in simulated low APs. The results indicate that the rheological responses with the varying AP gradients are relevant to the air entrainments in fresh mortar mixtures. The volume changes of air voids in fresh mortars are linearly related to the varying APs, which is owing to not only the AP difference between the inside and outside air voids but also the additional pressure on the liquid films of air voids stemming from the surface tension changes. Moreover, the Bingham capillary number is calculated to account for the air void deformability. Then rheological parameters are correlated to the content and deformability of air voids in fresh mortars. [ABSTRACT FROM AUTHOR]

Pumping changes the rheological properties, workability and construction performance of fresh concrete. However, there were limited knowledges on influences of discharge rates and pumping distances on the fresh properties of concrete. In this paper, effects of various discharge rates and pipeline lengths on rheological properties of self-consolidating concrete (SCC) after pumping were studied. A total of 12 SCC mixtures with the slump flow of 650–745 mm were pumped in pipelines with measured lengths of 342 m, 545 m, and 1044 m by constant discharge rates ranging between 5.1 and 11.4 L/s. Rheological properties were measured before and after pumping. Physical conditions of SCC during pumping, including pressure, shear, and temperature were estimated theoretically and experimentally. Moreover, the total organic carbon in the pore solution of SCC mixtures was measured to evaluate the change of superplasticizer adsorptions after pumping. Test results indicated that, due to pumping, the yield stress increased; the initial tangential viscosity decreased and the shear-thickening phenomenon was eliminated. The changes of yield stresses and viscosity were encouraged by discharge rates. Besides, lower initial slump flow of SCC exhibited a larger slump flow loss after pumping due to a higher shear rate experienced during pumping. The yield stress and viscosity after pumping increased with the increase of pipeline length at similar discharge rates, but decreased with the pipeline length under similar pumping pressures. The adsorption of superplasticizer increased after pumped at relative low discharge rates (5.2–5.7 L/s), but decreased at discharge rates of 7.7–10.8 L/s. [ABSTRACT FROM AUTHOR]

The influence of pumping on the rheological properties of self-consolidating concrete (SCC) is widely recognized, but there is still limited understanding of its behavior within the pipeline. In this study, we propose a novel approach using equilibrium distances to investigate the evolution of rheological properties along the pipeline. Full-scale horizontal pumping circuits spanning 328 m were established to assess the axial development of SCC's rheological properties. Thirteen mixtures, with water-to-cement (w/c) ratios ranging from 0.22 to 0.27, were pumped at discharge rates varying from 5.77 to 12.69 L/s. Our findings show that for pumping setups and material studied, both the w/c ratio of SCC and the discharge rate significantly affected the influence of rheological equilibrium distances on pressure loss gradient changes. In all tested samples, viscosity values required the entire length of the pipeline to reach post-pumping levels, while yield stress values rapidly achieved their fully developed state upon entering the pipeline. Importantly, the predicted pressure loss displayed a strong correlation with experimental measurements, with an accuracy of 89.42% across all tested mixtures. Our predictive model showed an average improvement of 4.6% in accuracy compared to the linear approach, with the most significant enhancement observed in samples with higher w/c ratios. This research sheds new light on the behavior of SCC during pumping and provides valuable insights for optimizing the pumping process. • The equilibrium distance of rheology is introduced to describe SCC flow behavior along the pipeline. • Horizontal pumping circuits spanning 328 m is used. • Factors affecting the equilibrium distance of rheology are discussed. • The prediction accuracy of the model is validated. [ABSTRACT FROM AUTHOR]

• Changes in rheological properties of high-strength concrete due to pumping were systemically investigated. • Fresh concrete was sampled in dismantled pipes for the rheological test. • Shear-thickening in high-strength concrete was eliminated after pumping. • Shearing energy during agitation and pumping was estimated and correlated to the changes in viscosity. Pumping of high-strength concrete (HSC) in high-rise or long-span structures is of paramount importance in constructions. However, pumping technology in practice is highly dependent on practical field experience, and full-scale testing that is carried out for complex projects involving new materials or long pumping distances. In this paper, a long pumping circuit was built to study changes in fresh properties of HSC due to pumping. In total, 10 HSC mixtures with strength grades of C60 to C100 were pumped at constant flow rates in pipelines measuring 348, 600 and 924 m in length. Rheological properties, workability characteristics, and concrete temperature were measured on concrete specimens sampled before and after pumping. Rheological properties of concrete sampled in dismantled pipes shortly after the end of pumping were also determined. Test results indicated that the yield stress increased, the initial tangential viscosity decreased and the shear-thickening phenomenon was eliminated due to pumping. The increase in yield stress mostly occurred in the first half of the pipeline, and the tangential viscosity decreased nearly linearly along the pipe length. The levels of drop in initial tangential viscosity were found to positively correspond to the calculated shearing energy, which is estimated given the shear rate, apparent viscosity and elapsed time during agitation and pumping. [ABSTRACT FROM AUTHOR]