Search

Resonant switched-capacitor converters have widely been used recently to increase conversion power density. The most significant drawback of these converters is voltage regulation problem when their input voltages vary in wide ranges. Here, a basic double voltage-ratio resonant switched-capacitor converter (SCC) is analyzed and simulated below its resonant frequency under the different operation modes to overcome this problem. The converter different parameters are calculated under both continuous conduction mode (CCM) and discontinuous conduction mode (DCM) conditions. The advantages and drawbacks of these operation modes are compared and the closed-loop control of the converter is also investigated based on the extended describing function approach. The given analyses demonstrate that the output voltage can be well-regulated under the CCM1 and DCM2 operation modes even when wide input voltage and load variations are applied. Besides, the DCM1 operation mode must be avoided when output voltage regulation is important. Based on the given analytical and experimental results, switching frequency varies in a reasonable range to regulate the output voltage. Also, faster transient responses, smaller output capacitor, and smaller resonant tank components can be used below the resonant frequency, as compared to the above resonant frequency, but lower efficiency value is achieved. The given approach has been extended to the other resonant SCCs as well. [ABSTRACT FROM PUBLISHER]

In single-phase grid-connected photovoltaic inverters, the input power is constant during the grid period, whereas the output power oscillates at double-line frequency. Therefore, electrolytic capacitors are widely used to handle the input and output power differences. However, these capacitors have short lifetime which degrade the inverter reliability. This paper proposes a control strategy to turn a conventional four-switch flyback-based inverter to an inverter equipped with a series power decoupling circuit. Therefore, a long lifetime film capacitor can be used as the main energy storage. The modified inverter has an inherent snubber circuit, which can restore energy of the transformer leakage inductance and improves its overall efficiency. The control strategy can realise maximum power point tracking and inject a sinusoidal low total harmonic distortion current to the grid. A 100 W prototype inverter has been built to verify operation and feasibility of the proposed control strategy. [ABSTRACT FROM AUTHOR]

A resonant switched-capacitor converter (SCC) has been analyzed above its resonant frequency to realize zero-voltage switching (ZVS) and to overcome voltage regulation issue of SCCs even when wide input voltage and output power variations are applied. ZVS operation under the continuous conduction mode (CCM) conditions improves efficiency due to lower conduction and switching losses. It is more efficient than the widely used zero-current switching (ZCS) approach in recent years under the discontinuous conduction mode (DCM) condition. Because, switching losses dominant components are reduced in MOSFET-based converters under the ZVS not ZCS conditions. Also, it has been demonstrated that output voltage can be well regulated under the CCM operation when wide input voltage and load variations are used. When output voltage regulation is not the major issue, operating at fixed switching frequency higher than, but near to, the resonant frequency results smaller components, higher power density, and lower electromagnetic interference level, as compared to the constant voltage ratio DCM operation mode, widely used in recent years. Also, output voltage ripple has been calculated, in details, by considering parasitic components of the output capacitor. A 110–165 to 200 V SCC has been implemented in 206.6–402.5 kHz frequency range to deliver 100–500 W. Maximum and average efficiency values equal to 96.8% and 94% are achieved, respectively. [ABSTRACT FROM PUBLISHER]

LLC resonant converter is one of the most suitable circuit topologies that have been introduced for designing constant output voltage switched-mode power supplies. In this paper, a design procedure is introduced for using this converter as a wide output range voltage source. Unlike constant output voltage applications which need small converter inductance ratio and narrow switching frequency variations, for wide output range applications, large values of these parameters are needed simultaneously and should be optimized. Instead of minimizing the components stresses, leading to a great value of the inductance ratio, proper choice of the converter parameters resulting in a smaller inductance ratio has been done. Maximum value of the capacitor in parallel with the power MOSFETs drain-sources has been derived to realize the zero voltage switching operation in the converter inductive region. Soft switching is achieved for all power devices under all operating conditions. A prototype of the converter has been tested for different regulated output voltages (35-165 Vdc) under different loads (0-3 Adc) and input voltages (320-370 Vdc) for using an ion implanter arc power supply, with maximum efficiency value of 94.7%. Experimental results confirm the high performance of the wide output range LLC resonant converter even under the worst case conditions. [ABSTRACT FROM AUTHOR]

LLC resonant converter has been widely used in dc–dc converters. In this paper, optimum dead-time and maximum switching frequency of a wide-adjustable-range LLC resonant converter are investigated for realizing the zero voltage switching (ZVS) operation even under the worst-case conditions. Analyses demonstrate that these parameters depend on the converter inductance ratio and ratio of the converter resonant capacitor and the effective capacitance appeared in parallel with the drain–sources of the power MOSFETs. The necessary dead time for realizing the ZVS operation can be minimized by choosing the normalized maximum switching frequency, properly. Using the dead-time optimum value, soft switching is achieved for all power devices even under the worst-case conditions. Developed prototype of the converter has been tested under different loads (0–3 A dc) and input voltage conditions (320–370 V dc) to achieve a wide-adjustable-range output voltage (40–165 V dc). This dc–dc converter is used as an ion implanter arc power supply. The calculated optimum dead-time and maximum switching frequency are approximately equal to 184 ns and 205.7 kHz, for realizing the ZVS operation at the worst-case conditions. These parameters in the prototype are approximately equal to 195 ns and 203.5 kHz, respectively. [ABSTRACT FROM PUBLISHER]