Search

This letter derives and discusses the superiority of a simple dc-link capacitor voltage control configuration for multilevel neutral-point-clamped converters with any number of levels. The control involves n − 2 control loops regulating the difference between the voltage of neighbor capacitors. These control loops are inherently decoupled, i.e., they are independent and the control action of one loop does not affect the others. This method is proven to be equivalent to previously published approaches, with the added advantages of increased simplicity and scalability to a higher number of levels, all while imposing a lower computational burden. The good performance of such control is confirmed through simulations and experiments. [ABSTRACT FROM AUTHOR]

The present paper provides a solution to operate multilevel dual active bridge (ML-DAB) converters built upon neutral point clamped switching legs in a full-bridge disposition and with any number of levels on either side of the converter. The main issue of such converters is addressing the inherent unbalance of the dc-link capacitor voltages, which hinders the proper operation and optimum utilization of the converter. The proposed solution comprises a generalized to N levels modulation and control scheme that allows operating these converters, while guaranteeing the proper balance of the dc-link capacitor voltages. The suitability of the proposed solution is verified through simulation and experimental tests performed in five different converter configurations, three of them with an asymmetric number of voltage levels, proving that capacitor voltage balance is achievable in a wide range of operation conditions. Moreover, the efficiency of the ML-DAB converters is demonstrated to be superior to the conventional two-level DAB case. [ABSTRACT FROM AUTHOR]

The conventional design of voltage-source power converters is based on a two-level half-bridge configuration and the selection of power devices designed to meet the full application specifications (voltage, current, etc.). This leads to the need to design and optimize a large number of different devices and their ancillary circuitry and prevents taking advantage from scale economies. This paper proposes a paradigm shift in the design of power converters through the use of a novel configurable device consisting on a matrix arrangement of highly optimized switching cells at a single voltage class. Each switching cell consists of a controlled switch with antiparallel diode together with a self-powered gate driver. By properly interconnecting the switching cells, the switching-cell array (SCA) can be configured as a multilevel active-clamped leg with a different number of levels. Thus, the SCA presents adjustable voltage and current ratings, according to the selected configuration. For maximum compactness, the SCA can be conceived to be only configurable by the device manufacturer upon the customer needs. For minimum cost, it can also be conceived to be configurable by the customer, leading to field-configurable SCAs. Experimental results of a 6 × 3 field-configurable SCA are provided to illustrate and validate this design approach. [ABSTRACT FROM AUTHOR]

This paper studies the coupling between the capacitor voltage control loops of diode-clamped (or functionally equivalent) multilevel multileg (multiphase) dc–ac converters. From a complete model of the plant revealing the coupling, a simple approach consisting in multiplying the vector of control commands by a constant matrix is proposed to decouple the control problem and achieve a better controller performance. Simulation and experimental results are presented to prove the superior performance of the proposed decoupled control. [ABSTRACT FROM PUBLISHER]

Aiming to improve the performance features of conventional two-level dual-active-bridge (DAB) converters, this paper presents a three-level neutral-point-clamped (NPC) DAB dc–dc converter. A general modulation pattern is initially defined, the dc-link capacitor voltage balancing is analyzed in detail, and a proper balancing control is designed. Then, a set of decoupled optimization problems is formulated as a function of the available modulation degrees of freedom to minimize the predominant converter losses. Finally, a simple and practical specific modulation strategy is provided, resembling the optimum solutions. The good performance of the proposed three-level NPC DAB converter operated with the proposed modulation strategy and voltage balancing control is verified through simulation and experiments. The capacitor voltage balancing can be guaranteed for all operating conditions. In addition, it is concluded that the multilevel topology provides benefits compared with the conventional two-level DAB converter. [ABSTRACT FROM PUBLISHER]

This paper presents a capacitor voltage balancing control applicable to any multilevel dc–ac converter formed by a single set of series-connected capacitors implementing the dc link and semiconductor devices, such as the diode-clamped topology. The control is defined for any number of dc-link voltage levels and converter legs (for single-phase and multiphase systems), guaranteeing the capacitor voltage control for any modulation index value and load (from idle mode to full power). The associated control loop small-signal transfer function is presented, from which optimum compensator design guidelines are derived. The improvement in control performance is verified through simulation and experiments comparing with a previous balancing control strategy in a four-level three-phase dc–ac conversion system. The satisfactory control performance is also verified through simulation in a four-level five-phase dc–ac conversion system. [ABSTRACT FROM PUBLISHER]

Neutral-point-clamped multilevel converters are currently a suitable solution for a wide range of applications. It is well known that the capacitor voltage balance is a major issue for this topology. In this paper, a brief summary of the basic topologies, modulations, and features of neutral-point-clamped multilevel converters is presented, prior to a detailed description and analysis of the capacitor voltage balance behavior. Then, the most relevant methods to manage the capacitor voltage balance are presented and discussed, including operation in the overmodulation region, at low frequency-modulation indexes, with different numbers of AC phases, and with different numbers of levels. Both open- and closed-loop methods are discussed. Some methods based on adding external circuitry are also presented and analyzed. Although the focus of the paper is mainly DC–AC conversion, the techniques for capacitor voltage balance in DC–DC conversion are discussed as well. Finally, the paper concludes with some application examples benefiting from the presented techniques. [ABSTRACT FROM AUTHOR]

A neutral-point-clamped three-level inverter with small dc-link capacitors is presented in this paper. The inverter requires zero average neutral-point current for stable neutral-point voltage. The small dc-link capacitors may not maintain capacitor voltage balance, even with zero neutral-point current. This may happen due to nonlinearities present in the circuit. This requires a fast control of the neutral-point voltage. A simple carrier-based modulation strategy which allows modeling of the neutral-point voltage dynamics as a continuous function of power drawn from the inverter is proposed. This continuous model shows that the neutral-point current is proportional to the power drawn from the inverter, and it enables the use of a well-established classical control theory for the neutral-point voltage controller design. A simple proportional integral controller is designed for the neutral-point voltage control on the basis of the continuous model. The design method for optimum performance is discussed. The implementation of the proposed modulation strategy and the controller is very simple. The controller is implemented in a 7.5-kW induction machine-based drive with only 14 \mu \F dc-link capacitors. Also, the experimental results show that fast and stable performance of the neutral-point voltage controller are achieved and thus verify the validity of the proposed control approach. [ABSTRACT FROM PUBLISHER]

The increasing installed wind power capacity has caused wind power generation to become a significant percentage of the entire electric power generation. As a consequence, the power system operators have included wind power plants regulation to improve the control of the overall power system, both in steady-state and transient operation. Therefore, wind power systems are required to verify the grid connection requirements stated by the power system operators. In presence of grid voltage dips, the low voltage ride-through (LVRT) requirement compliance produces a mismatch between the generated active power and the active power delivered to the grid. The conventional solution assumes that the active power surplus is dissipated in a dc-link resistor. In this paper, a control scheme for the back-to-back neutral-point-clamped converter is proposed. Under grid voltage dip, the controllers for generator-side and grid-side converters work concurrently to meet the LVRT requirement by storing the active power surplus in the turbine-generator mechanical system inertia while keeping constant the dc-link voltage. Simulation and experimental results verify the proposed control scheme. [ABSTRACT FROM PUBLISHER]