Search

In wide ac input frequency applications, such as more electric aircraft, ac input frequency of the three-phase buck rectifier varies in the range of 360–800 Hz. In this article, a reconstructed phase voltages based power following control for the three-phase buck rectifier under unbalanced input phase voltages in wide ac input frequency application is proposed. The input phase voltages are reconstructed to get more balanced modulation signals compared with the input phase voltages. The input currents are controlled to be in proportion to the reconstructed phase voltages to mitigate the imbalance of the input currents. The control strategy is simple and easy to be realized in digital. The analysis and design of the proposed control strategy and digital implementation are illustrated. An experimental prototype with 1.5 kW is built. The experimental results show that the sinusoidal input currents can be obtained when input phase voltages are unbalanced in wide ac input frequency application. [ABSTRACT FROM AUTHOR]

In this article, a power-split-based wireless charging system (WCS) with communication-free coordination control is proposed to combat wide load and coupling variations. By using a magnetic integrated inductor, two power delivery channels are created from a single receiver coil. Large portion of received energy is directly delivered to the load. Small amount of energy is converted by using a low-voltage low-power dc–dc converter to regulate the output voltage or current achieving constant voltage (CV) or constant current (CC) charging operation. This proposal achieves higher power conversion efficiency than the traditional two-stage cascaded converter WCS. Since the dc–dc converter only processes partial power of the WCS system, this proposal reduces the voltage stress of the devices and design difficulty. A communication-free coordination control is applied, which is established by sensing the input current drop caused by the burst operation of the partial-power dc–dc converter. Thus, the CC-CV charging is realized by PWM control at the receiver (Rx) side, and the inverter is regulated with subharmonics control scheme to maintain nearly constant Rx coil current. Simulation results for both high-voltage high-power scenarios and low-voltage low-power (LVLP) scenarios are provided to investigate the operation of the proposed WCS. Finally, experimental results are captured from a 250 W/60–84 V LVLP prototype to validate the feasibility and practicability of proposed concept. [ABSTRACT FROM AUTHOR]

In this article, a subharmonics switching technique named bifrequency pulse train (BF-PT) control for wireless battery charging system with tapped transmitter (Tx) winding is proposed to regulate the output power against the variation of load and coupling coefficient. The tapped Tx winding is spilt into two subwindings: subwinding I is connected to the inverter while subwinding II is in open circuit. The charging current and charging voltage can be acquired by measuring the induced current of subwinding I and the induced voltage of subwinding II, respectively, without dual-side communication. BF-PT control, which contains high- and low-frequency pulse trains, can achieve zero voltage switching over a wide operating range. The high- and low-frequency pulse trains are uniformly distributed to suppress the winding current oscillation and to minimize the output voltage ripple. When the coupling becomes weaker and/or light-load conditions, the switches are operated at the subharmonics frequency to further reduce the average switching frequency of the system. To verify the validity of the proposed method, a wireless charging system with 72 V/3 A output is fabricated. The experimental results confirmed that the proposed method is able to maintain constant current and constant voltage output regardless of the load and coupling variations. [ABSTRACT FROM AUTHOR]

The dead-time between the switches in the upper and the lower bridge of voltage source PWM converters produces input current distortion, called as dead-time distortion. The dead-time distortion can be compensated by trapezoidal voltage. The conventional trapezoidal voltage compensation method (TVCM) only controls the angle of the trapezoidal voltage. By the control of the angle and amplitude of the trapezoidal voltage simultaneously, an improved TVCM is proposed to further reduce the dead-time distortion. The experimental results are provided to verify the analysis results. [ABSTRACT FROM AUTHOR]

In this article, a half-bridge class-D audio amplifier (HB-CDAA) system with embedded bidirectional buck–boost converter is proposed. The proposed HB-CDAA system consists of a front-end symmetric bipolar output converter, a bidirectional buck–boost converter, and an HB-CDAA. With the help of the embedded bidirectional buck–boost converter, bus voltage pumping on the output of the front-end symmetric bipolar output converter of HB-CDAA can be suppressed. Thus, small ceramic capacitors can be used as bus capacitors to increase power density and to improve audio output quality. Furthermore, ZVS of the embedded bidirectional buck–boost converter can be achieved. The operating principle of the proposed circuit is analyzed and an experimental prototype is built. Experimental results show that ZVS of the embedded bidirectional buck–boost converter is achieved, and bus voltage pumping is successfully suppressed with small bus capacitors. [ABSTRACT FROM AUTHOR]

It is well-known that the ripple control technique benefits from fast load transient response and small cross regulation for single-inductor dual-output (SIDO) dc–dc converter. However, existing capacitor current ripple (CCR) controlled SIDO buck converter suffers from incomplete operation state and single switching path. Thus, it has a limited stable load range. In order to extend the stable load range and suppress cross regulation of SIDO buck converter in continuous conduction mode (CCM), a novel ripple control technique, called as capacitor current and capacitor voltage ripple (CCVR) control, is proposed in this article. The operation principle of the proposed CCVR controlled SIDO CCM buck converter is presented, and its discrete iterative map model is established. Furthermore, the stability and stable load range have been discussed by using bifurcation diagrams. Based on the established small signal model, Bode plots are given to show the performance in suppressing cross regulation. Finally, simulation and experiment results are provided to verify the theoretical analysis. It shows that the proposed CCVR control technique can be applied to SIDO CCM buck converter to extend its stable load range and suppress its cross regulation. [ABSTRACT FROM AUTHOR]

Inductive power transfer (IPT) systems with multiple output voltages are potential to supply a variety of loads simultaneously. This article proposes an IPT system with multiple semiactive rectifier cells (SARCs) connected in series at the receiver (Rx) side. These SARCs are independent of each other and their output voltages can be regulated individually with single receiver coil, which reduces the cost and volume. The proposed IPT configuration has the advantages of high flexibility, simple control, and no cross regulation. Considering that the SARC may cause additional reactance and lead to detuning of the Rx side, variable inductor is introduced to ensure the full tuning condition. Thus, the proposed IPT system can maintain zero phase angle operation with unity power factor in the whole load range, minimizing the reactive power losses. In addition, both primary inverter and the SARCs can achieve zero voltage switching. To verify the feasibility and validity of the proposed IPT system, an experimental prototype with two outputs of 640 W/150 V and 400 W/120 V is built. [ABSTRACT FROM AUTHOR]

Based on the current-mode switching cell (CMSC), an inductive power transfer (IPT) system with dual-output is proposed in this letter. In the proposed IPT system, two CMSCs are inversely connected in series at the Rx side. Two CMSCs operate in the positive half-cycle and in the negative half-cycle of the Rx coil current, respectively. The dual output voltages can be regulated independently. The circuit structure of the CMSC is quite simple and helps to make the Rx side more compact. The control scheme is based on Rx-side real-time regulation and thereby wireless communication links are not required. Additionally, zero voltage switching is ensured for all switches. In order to verify the theoretical analysis, an experimental prototype with 20 V/3.3 A and 5 V/3 A outputs is fabricated, and the maximum efficiency can reach 92.8%. [ABSTRACT FROM AUTHOR]

To regulate the output voltage of inductor–capacitor–capacitor-series (LCC-S) compensated wireless power transfer (WPT) system, a hybrid control strategy of phase shift modulation (PSM) and a switch-controlled capacitor is presented in this article. In the proposed hybrid control strategy, LCC-S compensated WPT system can realize wide output voltage regulation with zero voltage switching (ZVS), and the reactive current in a resonant tank can be minimized in the whole voltage range. Besides, the current in the primary coil of LCC-S compensated WPT system can be regulated with PSM, which helps to reduce the power loss of the primary coil at light load. Compared with conventional dual-loop hybrid control, the proposed hybrid control can regulate two control variables with one feedback loop simultaneously. To verify the theoretical analysis, a 500-W prototype with 400-V input voltage, 100−250-V output voltage is built. The experimental results show that the inverter can realize ZVS within the whole voltage range and a peak efficiency of 94.7% can be obtained. [ABSTRACT FROM AUTHOR]

In this letter, a digital control strategy with a simple transfer matrix between three-phase ac input voltages and dc-link voltage is proposed for a three-phase buck rectifier (3ph-BR) under unbalanced ac input conditions. The proposed digital control strategy can eliminate both the odd harmonics of the ac input currents and the even harmonics of the output voltage ripple under unbalanced ac input conditions. Compared with the state-of-the-art control strategies, the proposed control strategy does not require the extraction of the positive sequence voltage and the negative sequence voltage, thus a three-phase lock loop and complex calculation are not required. The proposed control strategy is essentially an input voltage feedforward control, which is independent of the loop bandwidth of the feedback system. Therefore, the processing speed of the digital processor is no longer the critical factor for the 3ph-BR under the unbalanced ac input conditions. The proposed control strategy makes it possible to utilize low-cost and small-sized digital processors. An experimental prototype of a 1.5-kW 3ph-BR with the proposed control strategy is built to verify the analysis results. [ABSTRACT FROM AUTHOR]

Pulse train (PT) control strategy for the boost power factor correction (PFC) converter operating in the continuous conduction mode (CCM) is proposed and studied in this article. Average current mode (ACM) control is usually utilized for the CCM boost PFC converter. The ACM-controlled PFC converter suffers from poor dynamic response, because its voltage control loop has to be designed with low bandwidth to minimize the effect of low-frequency output voltage ripple on the current control loop. Different from ACM control, the voltage control loop and current control loop of the PT-controlled PFC converter are decoupled, and thus the effect of low-frequency output voltage ripple on the current control loop is eliminated. Besides, PT modulation is utilized in the proposed controller to regulate the inductor current to follow the current reference. Thus, both high power factor and fast dynamic response can be achieved. The operation principle of the PT-controlled CCM boost PFC converter is analyzed, and a 300-W prototype is built to verify the analysis results. The experimental results show that power factor of the PT-controlled PFC converter is higher than 0.998 and the dynamic response is significantly improved. [ABSTRACT FROM AUTHOR]

In inductive power transfer (IPT) applications, load-independent output has become more popular. This letter proposes a reconstructed S-LCC topology with dual-type outputs, which can realize constant current (CC) output and constant voltage (CV) output simultaneously. The proposed reconstructed S-LCC topology uses the same number of passive components, inductor or capacitor, as conventional S-LCC topology while provides dual-type outputs, which results in reduced cost and size. Such dual-type outputs could be treated as two independent output ports without using any decoupling methods, which can simplify the parameter design significantly. The circuit model of the proposed reconstructed S-LCC topology is analyzed in detail. Comparison between the proposed reconstructed S-LCC topology and multicoil structure is performed. Experimental prototypes with 300V/1.5 kW CV output and 10A/1 kW CC output are fabricated to verify the feasibility of the proposed topology. [ABSTRACT FROM AUTHOR]

A LCC-S compensated wireless power transfer (WPT) system with dual decoupled receive coils and a cascaded PWM regulator is proposed in this brief. The dual decoupled receive coils, comprising of bipolar coil and unipolar coil, provide two power paths. Most of input power is transferred to load directly through bipolar coil while only small portion of input power is transferred through unipolar coil and the cascaded PWM regulator, which can reduce power loss effectively. The output voltage of WPT system is regulated by the cascaded PWM regulator, thereby wireless communication links (WCLs) is not required in the feedback control loop, which leads to simple control circuits and good stability. Compared with conventional WPT system with two-stage power conversion, it is cost-effective as voltage/current stress of PWM regulator can be significantly alleviated. Besides, the LCC-S compensated WPT system can operate under zero phase angle (ZPA) condition with low voltage-ampere rating components. A 1.5kW prototype is built and experimental results show that the system efficiency up to 93% can be achieved under full load, which is 2.3% higher than that of conventional WPT system with two stage power conversion. [ABSTRACT FROM AUTHOR]

Owing to the instantaneous difference between variable AC input power and the constant DC output power, power factor correction (PFC) converter suffers from serious double-line frequency (DLF) output voltage ripple. A Ripple-Suppressor (RS) in series with the PFC converter, which generates same magnitude but 180° phase shifted voltage as PFC converter output voltage ripple, is utilized in this brief to suppress the DLF output voltage ripple. The relationship among output impedance, audio sensitivity and output voltage ripple coefficient is analyzed, the closed-loop audio sensitivity and the stability of DLF ripple suppressor with constant on-time (COT) control are investigated. RS using a COT-controlled Buck converter can suppress DLF voltage ripple effectively with fast dynamic response and improved efficiency. Simulation and experimental results are given to verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

A phase-shift pulse-frequency modulation (PS-PFM) for a full-bridge LCC resonant converter is proposed in this paper to reduce both switching frequency variation range and reactive power of a traditional PFM LCC resonant converter. Like the PFM LCC resonant converter, a PS-PFM LCC resonant converter has a wider zero voltage switching operation range than a phase-shift modulated LCC resonant converter. By integrating a voltage-controlled carrier generator, the proposed PS-PFM modulator can adjust phase-shift angle and switching frequency simultaneously, resulting in one more degree of control freedom to optimize the steady-state performance of an LCC resonant converter. A detailed analysis of the proposed PS-PFM LCC resonant converter is performed and a step-by-step parameter design procedure is given. A 500-W/48-V prototype with 100–200 V input voltage is built to verify the theoretical analysis. The maximum efficiency of the prototype reaches 95.3%. [ABSTRACT FROM AUTHOR]

Power factor correction (PFC) converter suffers from serious double-line-frequency output voltage ripple due to the difference between instantaneous ac input power and dc output power. To suppress such double-line-frequency output voltage ripple, a ripple cancellation circuit (RCC) is utilized to generate the same magnitude but 180° phase shifted double-line- frequency voltage ripple. This paper provides an insight into the relationship between control scheme and double-line-frequency ripple suppression from the perspective of audio susceptibility model. For the purpose of reducing the double line frequency ripple, the closed-loop audio susceptibility of series RCC should be designed relatively low at double line frequency. According to such requirement, a ripple controller with improved voltage feed-forward (FF) scheme and quasi-proportional-resonant (QPR) compensator is designed. As QPR compensator can increase the denominator of the closed-loop audio susceptibility, while voltage FF scheme can reduce its numerator, its magnitude at double line frequency is thus greatly reduced and double-line-frequency ripple is also significantly suppressed. Moreover, due to the flexibility of QPR compensator, the proposed ripple controller presents good ripple suppression in a different line frequency application. Finally, experimental results of a flyback PFC with buck-type RCC quasi-single-stage ac–dc converter are provided to verify the validity of the proposed ripple controller. [ABSTRACT FROM AUTHOR]

A flicker-free single switch multi-string LED driver with high power factor and current balancing is proposed and analyzed. It combines a pre-stage boost PFC converter and multiple second-stage buck dc–dc converters by a single active switch and multiple dc-link capacitors. With the proposed circuit configuration of multiple dc-link capacitors, the output current of each LED string can be balanced. Therefore, by controlling the output current of one LED string, the output currents of other LED strings can be controlled via current balancing of dc-link capacitors. The effect of the ripple of dc-link voltage on each output can be eliminated by fast voltage mode control loop. Therefore, flicker-free low ripple current for each LED string is achieved. With small voltage ripple across dc-link capacitors, the turn on time of active switch is almost constant in a half line cycle. Therefore, power factor correction can be achieved with inductor current of pre-stage operating in discontinuous conduction mode (DCM). Finally, prototypes of dual-string LED driver with 90–135 Vac input and 175–265 Vac input for 47 W output power are built to verify the studied results. [ABSTRACT FROM AUTHOR]

MR16 lighting system with a high-frequency step-down electronic transformer is widely used in commercial lighting. In this paper, a single-switch quadratic boost light emitting diode (LED) driver compatible with electronic transformers for the MR16 lighting system is proposed and analyzed. It combines a prestage boost power factor correction (PFC) converter and a second-stage boost dc–dc converter with a single switch. The effect of the dc link voltage ripple of the prestage boost PFC converter on the output of the second-stage boost dc–dc converter is eliminated by a fast voltage mode control loop of a second-stage circuit. Therefore, flicker-free low ripple LED current is achieved. With a small dc link voltage ripple of prestage, the turn-on time of the active switch is almost constant in a half-line cycle. Therefore, PFC can be achieved with inductor current of prestage operating in a discontinuous conduction mode. With small input capacitance, the proposed LED driver presents a good compatibility performance with different kinds of electronic transformers. Furthermore, the proposed LED driver needs only one active switch and one control loop, which makes circuit volume small and low cost. Finally, a 4 W LED driver for a small-size MR16 lighting system is provided to verify the studied results. [ABSTRACT FROM AUTHOR]

A single-stage ac–dc converter with high power factor (PF) usually suffers from a significant output voltage ripple at double line frequency. In order to suppress such low-frequency output voltage ripple and maintain high PF, a series compensation circuit (SCC), which generates the same magnitude but 180° phase shifted low-frequency voltage ripple, is connected in series with the output of a power factor correction (PFC) converter. In this paper, an output impedance model of the SCC is established and the relationship between the output impedance of the SCC and the low-frequency output voltage ripple of an ac–dc converter is analyzed. Based on the proposed output impedance model, a low-frequency output voltage ripple can be evaluated. To further reduce the low-frequency output voltage ripple, an output impedance shaping method with a virtual impedance is presented. The implementation of the virtual impedance of the SCC with average current mode control is studied. A flyback PFC converter with a buck SCC is implemented for the study of the suppression of the low-frequency output voltage ripple. A prototype is designed to verify the analysis results. [ABSTRACT FROM AUTHOR]

In this paper, a digital-based pulse train (PT) control technique for a boost power factor correction (PFC) converter operating in a discontinuous conduction mode (DCM) is presented, which can achieve nearly unity power factor (PF) over a universal input voltage range. Different from traditional digital control techniques, which usually require complex arithmetic operations, the digital-based PT control technique only needs a simple operation. Besides, a DCM boost PFC converter with digital PT control can operate at a high switching frequency, which is less dependent on the processing speed of a digital controller. Thus, the proposed control strategy can be implemented with general purpose digital controllers, such as low-speed and low-cost microcontroller unit, for the DCM boost PFC converter where the cost is a focus. The operation principle of the digital PT controlled DCM boost PFC converter is analyzed. Experimental results are provided, which show that high PF and low input current total harmonic distortion can be maintained over a universal input voltage range of 90–264 V ac. [ABSTRACT FROM AUTHOR]

For a single-inductor dual-output (SIDO) dc–dc converter operating in continuous conduction mode (CCM), load variation of one output will affect the voltage of the other output, i.e., there exists cross regulation between its two outputs. To suppress the cross regulation of the SIDO dc–dc converter operating in CCM, a novel ripple based control technique, called capacitor current ripple (CCR) control technique, is proposed in this paper. The operation principle of the SIDO CCM buck converter and the proposed CCR control technique are presented. The small signal model of the CCR-controlled SIDO CCM buck converter is established by the state space averaging method. Bode plots based on small signal model show that the proposed CCR-controlled SIDO CCM buck converter significantly reduces cross regulation and improves the transient performance compared with the peak current mode controlled SIDO CCM buck converter. In addition, the effect of the variation of loads on the stability of the proposed CCR-controlled SIDO CCM buck converter is analyzed by eigenvalues analysis. Finally, experimental results are provided to verify the analysis results. [ABSTRACT FROM AUTHOR]

Compared with traditional two-stage class-D audio amplifier, audio amplifier based on cycloconverter-type single-stage inverter (CSSI) has advantages of high efficiency and no bus voltage pumping (BVP). However, CSSI requires complex active clamp circuits for the current commutation of cycloconverter, especially for multichannel amplification. In this letter, a 2.1-channel switching amplifier with dc/high-frequency-ac (HFAC) mixed power supply is proposed, where CSSI is used as low-frequency audio channel amplifier and two class-D amplifiers are used as high-frequency audio channel amplifiers. With dc/HFAC mixed power supply, the proposed 2.1-channel switching amplifier does not require additional active clamp circuits for current commutation of cycloconverter. Besides, wide range soft switching of cycloconverter switches can be achieved. Benefiting from single-stage power conversion of low-frequency audio channel and wide range soft switching of cycloconverter switches, high efficiency of the proposed 2.1-channel amplifier is achieved. Without BVP, low voltage stress of switches and low distortion of low-frequency audio signal are realized in the proposed 2.1-channel amplifier. A 200-W prototype is presented to verify the analysis results. [ABSTRACT FROM AUTHOR]

Both constant on-time (COT) and fixed off-time (FOT) control techniques are suitable for various applications requiring fast transient response. However, the discrete-time model of COT controlled buck converter only has two switched borderlines, whereas that of FOT controlled buck converter has four switched borderlines. Based on the derivations of these borderlines, an asynchronous-switching map of FOT controlled buck converter is established. With the decrease of equivalent series resistance (ESR) of output capacitor, instability and mode shifting from continuous conduction mode (CCM) to discontinuous conduction mode (DCM) are discussed. Furthermore, with small ESR of output capacitor, stability effects of load resistance and inductance on dynamical behaviors are investigated, and the approximate stability criteria and the corresponding normalized critical conditions are obtained. The theoretical analyses and experimental results show that the converter operates in DCM chaos via period-doubling and border-collision bifurcation routes, and its instability caused by small ESR can be removed by choosing appropriate load resistance, inductance, and voltage transfer ratio, which are very suitable for the circuit design of FOT controlled buck converter. [ABSTRACT FROM AUTHOR]

Compared with constant duty cycle-controlled discontinuous conduction mode (DCM) boost power factor (PF) correction (PFC) converter, constant duty cycle-controlled quadratic DCM–DCM boost PFC converter features with much lower second-order line frequency output voltage ripple, and however, it suffers from low PF. To increase PF of quadratic DCM–DCM boost PFC converter, a variable duty cycle control technique for quadratic DCM–DCM boost PFC converter is presented in this paper. An approximation equivalent for the variable duty cycle is employed to simplify the implementation circuit. The corresponding expressions of PF and output voltage ripple are analyzed. For input voltage range of 100–240 Vac, quadratic DCM–DCM boost PFC converter with variable duty cycle control benefits with very high PF, and tradeoff between PF and output voltage ripple of this converter is analyzed. Experimental results from 100-W prototypes are given to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

It is known that the ripple-based control of a switching dc–dc converter benefits from a faster transient response than a conventional pulse width modulation (PWM) control switching dc–dc converter. However, ripple-based control switching dc–dc converters may suffer from fast-scale oscillation. In order to achieve fast transient response and ensure the stable operation of a switching dc–dc converter over a wide load range, based on a conventional pulse train (PT) control technique, a peak capacitor current PT (PCC-PT) control technique is proposed in this paper. With a buck converter as an example, the operating modes, steady-state performance, and transient respond performance of a PCC-PT controlled buck converter are presented and assessed. To eliminate fast-scale oscillation, circuit and control parameter design considerations are given. An accurate discrete iteration model of a PCC-PT controlled buck converter is established, based on which the effects of circuit parameters on the stability of the converter operating in a discontinuous current mode (DCM), mixed DCM-continuous conduction mode (CCM), and CCM are studied. Simulation and experimental results are presented to verify the analysis results. [ABSTRACT FROM PUBLISHER]

This paper describes a systematic procedure using power flow graphs for generating all possible double-input single-output (DISO) dc/dc converters. To maximize the generality of applications, the input ports can possibly be connected with voltage source(s) or current source(s), and the output port can be connected with a voltage load or current load. The control methods are described in this paper. A DISO converter with two voltage sources and one voltage load is taken as an example to analyze a few key properties of practical relevance, including input voltage range, efficiency, power distribution, and switching stress. A popular application of DISO converters involves the use of a battery as storage element, and for this specific case, possible choices for the converters, the control method, and the attainable efficiency are discussed. Finally, experimental results are presented to verify the analytical results. [ABSTRACT FROM PUBLISHER]

An asymmetrical hybrid‐controlled half‐bridge LCC resonant converter which integrated a buck–boost converter and a half‐bridge LCC resonant converter is proposed. It benefits with wide soft switching range, low conduction loss and high power density. By utilising an asymmetrical hybrid control strategy, its switching frequency and duty ratio can be adjusted simultaneously. The proposed LCC resonant converter maintains output voltage regulation and zero‐voltage switching of switches in wide input voltage and load variation range. Experiment results of a 500 W prototype are provided to verify the theoretical analysis results. [ABSTRACT FROM AUTHOR]

A single-inductor dual-output (SIDO) buck–boost power factor correction (PFC) converter operating in critical conduction mode is proposed in this paper. By multiplexing a single inductor, each output of the SIDO buck–boost converter can be regulated independently. Compared with a conventional two-stage multiple-output converter, the SIDO buck–boost PFC converter benefits from significant overall cost saving, small size, and light weight. Moreover, the efficiency of the SIDO buck–boost PFC converter can be improved due to single-stage power conversion. The control strategy and characteristics of the proposed converter are analyzed. The efficiency, power factor, total harmonic distortion, and output accuracy are verified using the experimental results. [ABSTRACT FROM PUBLISHER]

Pulse train (PT) control technique realizes the output voltage regulation of switching dc–dc converters by using preset high power control pulse PH and low power control pulse PL. In steady state, PH and PL in some successive switching cycles constitute a control pulse repetition cycle. The control pulse combination of PH and PL in the control pulse repetition cycle has a significant effect on the performances of PT controlled switching dc–dc converters. In this paper, by taking PT controlled discontinuous conduction mode buck converter as an example, the control pulse combination of PT controlled buck converter is studied. Some lemmas to reveal the control pulse combination are presented, and the combination of PH and PL in a control pulse repetition cycle is obtained. Based on which, the steady-state and transient performances of PT controlled buck converter are investigated. The control pulse combination-based analysis of PT controlled buck converter provides an effective way to understand the PT control technique in detail. [ABSTRACT FROM PUBLISHER]

A variable on-time (VOT) control strategy for a critical conduction mode (CRM) flyback power factor correction (PFC) converter with low total harmonic distortion (THD) and high power factor (PF) is proposed in this paper. By using input voltage and the voltage across the auxiliary winding of the flyback transformer to modulate the turn-on time of the switch of the CRM flyback PFC converter, the PF and THD of the converter can be improved. The operation principles of the traditional constant on-time (COT)-controlled CRM flyback PFC converter and VOT-controlled CRM flyback PFC converter are analyzed. The experimental results show that the PF and THD of the VOT-controlled CRM flyback PFC converter are better than those of the COT-controlled CRM flyback PFC converter. [ABSTRACT FROM PUBLISHER]

Bi‐frequency (BF) control for LLC resonant converter is proposed and studied. Compared with conventional voltage mode control of LLC resonant converter, which realises output voltage regulation by adjusting control pulse frequency cycle by cycle, BF control of LLC resonant converter realises its output voltage regulation by adjusting the combination of two preset control pulses with 50% duty ratio and different switching frequencies. BF controlled LLC resonant converter benefits from simple controller design and fast transient response. A 130 W prototype is presented to verify the analysis results of BF control method. [ABSTRACT FROM AUTHOR]

SUMMARY Contrast to conventional dependent double-edge (DDE) pulse-width modulation (PWM), independent double-edge (IDE) PWM is investigated and applied to the control of switching dc-dc converters, with improved digital-peak-voltage (IDPV) controlled buck converter in this paper. IDE modulation unifies all the PWM schemes reported up to now and is thus called as unified PWM. It is revealed that conventional trailing-edge, leading-edge, trailing-triangle, and leading-triangle modulations are special cases of IDE modulation. The control laws of IDPV controlled buck converter with IDE modulation are investigated and compared with those of IDPV with DDE modulation. Their stabilities and robustness are analyzed subsequently. Digital implementation of the unified PWM is also carried out. Steady-state and transient performances of IDPV controlled buck converters with IDE modulation and DDE modulation are compared and verified by experimental results. It is concluded that steady-state and transient performances of IDPV with IDE are better than those of IDPV with DDE modulation. Copyright © 2012 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]

The pulse-train (PT) control technique for switching dc–dc converters is simple to design and benefits from excellent control performance. Up to now, almost all of the works on PT control are focused on switching dc–dc converters operating in discontinuous conduction mode, with few works reported on PT control of switching dc–dc converters operating in continuous conduction mode (CCM). In this paper, a PT-controlled CCM buck converter is studied and a unique low-frequency oscillation phenomenon is revealed, which results in large undesired inductor-current and output-voltage variations. The effect of equivalent series resistance (ESR) output-capacitor on the low-frequency oscillation is examined. The results indicate that such oscillation occurs when the ESR output-capacitor is relatively small and disappears when it is relatively large. However, a larger ESR will result in a large output-voltage ripple. In order to avoid the low-frequency oscillation and, at the same time, to ensure a small output-voltage ripple, the ICRIF circuit is applied. In this way, a small ESR output-capacitor can be used to decrease the output-voltage ripple. Simulation and experimental results are provided to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

Improved pulse regulation (IPR) control, a novel control technique for switching dc–dc converters, is proposed and studied in this paper. According to the output voltage and load current of the switching dc–dc converter, IPR control technique achieves output voltage regulation by generating control pulse train made up of some preset control pulses with different duty ratios. IPR control needs only comparators, triggers, and some simple logic devices, without error amplifier and the corresponding compensation circuit of pulse width modulation control scheme, thus IPR control scheme is easy to realize, benefits with excellent transient performance and stability. The principle and operation of IPR control scheme are introduced and illustrated with buck converter operating in discontinuous conduction mode as an example. Simulation and experimental results are presented to show that IPR-controlled converter has much lower output voltage ripple and more accurate output voltage regulation than PR converter. [ABSTRACT FROM PUBLISHER]

Equivalent series resistance (ESR) of output capacitor has a significant effect on the control performance of constant on-time (COT) controlled switching dc-dc converters. In this paper, a discrete-time model of COT-controlled buck converter, with variable sampling frequency, is established. Based upon which, the dynamical effects of the ESR of output capacitor on COT-controlled buck converter are revealed and analyzed. The time-domain numerical simulations of the exact switched state equations, the bifurcation diagrams, and maximal Lyapunov exponents of the discrete-time model are obtained. These results verified by experimental circuit indicate that the ESR of output capacitor is a critical factor for COT-controlled buck converter, which can eliminate the unique pulse bursting phenomenon and shift operation mode from discontinuous conduction mode to continuous conduction mode, as well as control stability. [ABSTRACT FROM PUBLISHER]

The output characteristics of a single-phase inverter with voltage and current dual closed-loop feedback control are analyzed, and the equivalent circuit model of a parallel single-phase inverter system is introduced. By taking both resistance and inductance components of the equivalent output impedance into consideration, a current decoupling control strategy of the parallel inverter system is then proposed. Furthermore, by constructing a three-phase balanced current according to the output current of the single-phase inverter, an active and reactive current decomposition method is presented to decompose the output current of the single-phase inverter into active and reactive currents according to the instantaneous reactive power theory. The block diagram of the active and reactive current decomposition method is given, and current decomposition simulation results are shown to verify the analysis results. The prototype is developed, and the control of two parallel-connected 2-kVA inverters is realized. The experimental results show its feasibility and effectiveness. [ABSTRACT FROM PUBLISHER]

In this paper, the effect of equivalent series resistance (ESR) of an output capacitor on the performance of a constant-on-time (COT)-controlled buck converter is studied, and a pulse bursting phenomenon is revealed. It indicates that the ESR of the output capacitor is one of the key factors causing pulse bursting phenomenon in COT-controlled buck converters, and the critical ESR is derived via time-domain analysis and stability analysis in the s-domain. It is pointed out that, when the ESR of the output capacitor is smaller than the critical ESR, pulse bursting phenomenon occurs; otherwise, it disappears. Simulation and experimental results are provided to verify the theoretical analysis results. [ABSTRACT FROM AUTHOR]

A novel pseudo-continuous conduction mode (PCCM) boost power-factor-correction (PFC) converter and its corresponding control strategy are proposed in this paper. Connecting a power switch in parallel with the inductor makes the boost converter operate in PCCM, which provides an additional degree of control freedom to realize PFC control. Therefore, a simple and fast voltage control loop of the PCCM boost PFC converter can be designed to realize output-voltage regulation. The additional degree of control freedom introduced by inductor current freewheeling operation of the PCCM boost PFC converter has been exploited through the dead-zone control technique, which can be dynamically adjusted in accordance with the output-voltage ripple. Compared with continuous conduction mode (CCM) boost PFC converter, the controller of the proposed PCCM boost PFC converter is much simpler. Moreover, the PCCM boost PFC converter benefits with reduced inductor-current ripple and improved power factor compared with boost PFC converter operating in discontinuous conduction mode (DCM). Analysis, simulation, and a 400-W prototype of the PCCM boost PFC converter have been presented and compared with those of boost PFC converters operating in conventional CCM and DCM. The results show that the dynamic response of the PCCM boost PFC converter is significantly faster than the existing boost PFC converter. [ABSTRACT FROM AUTHOR]

A novel control technique, called bifrequency pulse-train (BF-PT) control technique, for switching dc–dc converters is proposed. In contrast to the conventional pulsewidth-modulation-based control technique of switching dc–dc converters, which realizes the output voltage regulation by adjusting the duty ratio of the control pulse cycle by cycle, the BF-PT control technique realizes the output voltage regulation of switching dc–dc converters based on the presence and absence of preset high- and low-frequency control pulses. In BF-PT control, the output voltage of switching dc–dc converter is sampled at the beginning of each switching cycle and compared with a reference voltage to determine whether a high- or low-frequency control pulse should be selected as the control pulse. The BF-PT control technique is simple and cost effective and enjoys fast transient response. In addition, two types of control pulses with different switching frequencies spread the emission spectrum over discrete frequencies, resulting in lower electromagnetic interference (EMI) noise and easier EMI filter design. Furthermore, more low-frequency control pulses at lighter load improve the light-load power conversion efficiency. A buck converter operating in discontinuous conduction mode is taken as an example to illustrate the application and benefits of BF-PT control technique. Simulation and experimental results are presented to verify the analytical results. [ABSTRACT FROM PUBLISHER]