Search

In AC microgrids, voltage source inverters (VSIs) have become widely employed to interface DC energy sources to the AC network. Apart from power generation, VSI-based energy sources can also perform ancillary services such as demand side management using conservation voltage reduction (CVR). In conventional distribution systems, CVR involves lowering the voltage levels of the system within permissible limits to reduce the amount of power consumed by certain loads. However, in autonomous microgrids, the application of CVR for demand side management has not been fully explored yet. Thus, in this paper, a CVR strategy for a droop-controlled VSI-based distributed generation (DG) operating in an autonomous microgrid is proposed. This strategy employs the deviation in DG output voltage magnitude and frequency, caused by an increase in power demand during peak and overloading conditions, to determine the amount of voltage compensation required to reduce the microgrid bus voltages. In addition, a controller to coordinate between the proposed CVR strategy and load shedding is also developed to operate the DGs during overloading conditions. The proposed strategy is verified with a microgrid test system, and its performance is validated on MATLAB/Simulink software environment. [ABSTRACT FROM AUTHOR]

This paper provides a critical assessment of oscillatory modes for a droop-controlled multi-microgrid (MMG) consisting of inverter-based and synchronous-based distributed generation (DG). Local and inter-microgrid oscillatory modes similar to conventional interconnected power systems are observed. However, an additional new and more “dominant” oscillatory mode caused by interactions between close-by coherent synchronous-based and inverter-based DGs in the MMG is identified. Sensitivity analysis is employed to assess the impact of various MMG configurations and parameters such as: interconnecting line length, droop gain, exciter gain, and governor gain on MMG oscillatory modes. Parametric studies are conducted to highlight the impact of oscillatory modes on MMG transient and dynamic performances. Consequently, power system stabilizers (PSSs) are developed for both inverter-based and synchronous-based DGs to improve the transient and dynamic performances of the MMG. Residues are calculated and therefore utilized to determine the effect of PSS placement on the MMG oscillatory modes. Finally, small-signal stability analysis results and the performances of the PSSs are validated through time domain simulations on MATLAB/Simulink. [ABSTRACT FROM AUTHOR]

This paper proposes a new topological configuration for a unified power quality conditioner (UPQC). Generally, the power structure of the three-phase three-wire UPQC consists of two back-to-back connected six-switch inverters. For this configuration, out of 12 switches, six of the series inverter switches will be underutilized most of the time. To improve the semiconductor utilization and consequently to reduce the total switch count, this paper proposes a new reduced switch topology for the UPQC. The proposed topology is realized using only ten switches and retains all the performance merits of the 12-switch UPQC while minimizing its underutilization without increasing the switch VA rating. The paper provides a detailed analytical study and evaluation by comparing the proposed topology with the twelve- and nine-switch-based UPQC system configurations. The feasibility of the proposed topology is validated through experimental investigation. [ABSTRACT FROM AUTHOR]

This paper presents a novel dc-link scheme for enhancing the fault ride-through (FRT) capability of doubly fed induction generator-based wind turbine (DFIG-WT). The proposed system consists of parallel capacitors with a dedicated control strategy designed to provide means for power evacuation during grid fault conditions. This technically simple and cost-effective scheme was developed considering transmission line autoreclosing which may cause multiple fault inceptions. Simulation studies were carried out to compare the performance of the introduced solution with a DFIG-WT, equipped with the dc chopper and crowbar. The simulation results demonstrate the enhanced performance of the proposed approach in maintaining the dc-link voltage, transient rotor voltages, and currents within the permissible operating range during a bolted three-phase-to-ground fault. The proposed schemes were also tested in response to asymmetrical grid faults, and the enhancement in transient response has been verified. An experimental setup was developed to emulate the behavior of the dc-link circuit during fault conditions. These experimental results demonstrate the effectiveness of the switching parallel capacitors in preventing dc-link overvoltage during imbalance power operation. The discharging capacitor circuit highlighted the capability of tackling the multiple fault inception problems while adhering to grid code requirements. [ABSTRACT FROM PUBLISHER]

Planning distribution systems without considering the operation status of multiple distributed generation (DG) units could result in constraining the network, lowering the utilization of its assets and minimizing the total DG capacity that can be accommodated. In this paper, the impact of multiple DG configurations on the potential of active network management (ANM) schemes is firstly investigated. Secondly, the paper proposes a multi-configuration multi-period optimal power flow (OPF)-based technique (MMOPF) for assessing the maximum DG capacity under ANM schemes considering 1) variability of demand and generation profiles (multi-period scenarios), and 2) different operational status of DG units (multi-configurations). The results show that the availability of DGs at certain locations could critically impact the amount of DG capacity at other locations. If DGs are properly allocated and sized at certain locations up to the optimal limits, even with a “fit-and-forget” approach, the total connected DG capacity can be maximized, with minimum utilization of ANM schemes. However, exceeding these optimal limits may lead to minimizing the total DG penetration in the long term, impacting the system reliability due to the operational status of multiple DG units, and consequently, imposing more investments on ANM schemes to increase the amount of connected DG capacity. [ABSTRACT FROM AUTHOR]

This paper presents an optimization procedure that enables the optimal dispatching of distributed generators and storage systems in a medium-voltage islanded microgrid. The network is assumed to be supplied by programmable (dispatchable) and nonprogrammable generators (i.e. nondispatchable, such as renewable energy sources—based units). The optimization goal is to minimize the overall microgrid operating cost and the pollutants emission of the programmable generators, assuming that all of the power made available by the renewable generators (photovoltaic and wind systems) is either directly injected into the network or stored in order to be subsequently delivered according to the proposed storage units' management strategy. The optimization is carried out by a niching evolutionary algorithm (NEA) that is able to find multiple optima and the variation of the objective function in their neighborhood. NEAs allow overcoming the performance of standard algorithms used for optimal power-flow calculations in power systems by avoiding falling into local optima. The optimization procedure is performed on a test microgrid and verified by computer simulations. The numerical results show that the solutions can always improve the microgrid performances irrespective of the network operating conditions in all of the considered cases. [ABSTRACT FROM AUTHOR]

Seamless formation and robust control of distributed generation microgrids are essential requirements to facilitate powerful and flexible control infrastructure in future smart power grids. Motivated by this objective, this paper presents a control structure for microgrid converters based on direct-voltage control and optimized dynamic power sharing. The salient features of the proposed scheme are 1) minimum switching actions between grid-connected and isolated microgrids systems to minimize internal microgrid formation disturbances; 2) active damping control performance in the converter control voltage vector to effectively reject both voltage magnitude disturbances and power angle swings associated with mode transition and load disturbances; and 3) high bandwidth direct voltage control loop in both grid-connected and isolated microgrid modes to improve the dynamic response and disturbance rejection performance. Theoretical analysis and comparative experimental results are presented to validate the effectiveness of the proposed control scheme. [ABSTRACT FROM AUTHOR]