Search

This paper aims at characterizing and improving the metrological performances of current and voltage instrument transformers (CTs and VTs) in harmonic measurements in the power system. A theoretical analysis is carried out to demonstrate that, due to the iron core nonlinearity, CT and VT output signal is distorted even when the input signal is a pure sine wave. Starting from this analysis, a new method for CT and VT characterization and compensation is proposed. In a first step, they are characterized in sinusoidal conditions and the harmonic phasors of the distorted output are measured; in the second step, these phasors are used to compensate the harmonic phasors measured in normal operating conditions, which are typically distorted. The proposed characterization and compensation techniques are called SINusoidal characterization for DIstortion COMPensation (SINDICOMP). Several experimental tests, using high-accuracy calibration setups, have been performed to verify the proposed methods. The experimental results showed that the SINDICOMP technique assures a significant improvement of CT and VT metrological performances in harmonic measurements. [ABSTRACT FROM AUTHOR]

A novel measurement approach for power-flow analysis in medium-voltage (MV) networks, based on load power measurements at low-voltage level in each secondary substation (SS) and only one voltage measurement at the MV level at primary substation busbars, was proposed by the authors in previous works. In this paper, the method is improved to cover the case of temporary unavailability of load power measurements in some SSs. In particular, a new load power estimation method based on artificial neural networks (ANNs) is proposed. The method uses historical data to train the ANNs and the real-time available measurements to obtain the load estimations. The load-flow algorithm is applied with the estimated load powers, and the MV network state variables are obtained. The proposed method is validated for the real MV distribution network of the island of Ustica. The loads of selected SSs are estimated for two full days of different seasons. In comparison with previous works, satisfactory results are obtained in terms of uncertainty in the calculated power flows, thus suggesting the applicability of the proposed method for real-time monitoring of MV distribution networks. [ABSTRACT FROM AUTHOR]

With the increasing presence of distributed generators (DGs), the implementation of a smart sensors and actuators network in distribution grids has become crucial for different monitoring, management, and protection functionalities. For DGs monitoring and control, sensors and actuators are usually embedded in so-called interface devices (IDs) or interface protection systems. Existing IDs lack in communication interfaces both to the electrical energy distribution system operators (DSOs) and to the DGs inverter. In this framework, the authors have developed a new ID solution and a proper communication architecture, which allow implementing new smart functionalities based on the interaction with the DSO, such as remote control of DG power production or islanding detection. Regarding this last aspect, a new islanding algorithm is proposed, based on both local measurements and communications with DSO. The effectiveness of the proposed solution is shown on the real case study of Ustica Island’s distribution network. [ABSTRACT FROM PUBLISHER]

This paper deals with the issue of measurement device placement for load flow analysis in medium-voltage (MV) distribution networks. The study is carried out using an innovative measurement algorithm for load flow analysis developed by the authors. It is based on low-voltage (LV) load power measurements applied on a backward/forward algorithm for the load flow resolution. The final aim is to identify the most suitable number and placement of the LV measurement points in order to limit the uncertainty on the power flow estimation to a target value. The proposed approach is based on the uncertainty evaluation of the estimated power flows; a sensitivity analysis is performed in order to assess the uncertainty contribution of each LV power measurement to the estimated power flow upstream of each MV feeder of the distribution network. The LV measurement device placement is presented and discussed in a real case study, i.e., the distribution network of the Ustica Island. [ABSTRACT FROM AUTHOR]

This paper proposes a novel measurement procedure for load flow analysis in medium voltage (MV) smart grids. The new approach is based on power measurements at low voltage (LV) side of MV/LV distribution substations. Such measurements are carried out by means of power quality analyzers. If compared with the load flow methods based on measurements at the MV side, the proposed approach has a lower cost and it offers an equally reliable measurement system. The proposed algorithm takes the basic concept of the current summation backward/forward method; some modifications are introduced to use LV load powers measurements. To this aim, the MV/LV power transformer is properly modeled and taken into account in the algorithm. The proposed approach is validated by means of both simulations and experimental measurements; the test system is the MV distribution grid of Ustica Island, Italy. First, the proposed algorithm is compared with the MATLAB/Simulink load flow tool, which is based on the traditional Newton-Raphson method. Second, a comparison is carried out between the proposed method and the measurement data collected in the actual MV network of Ustica. Such comparison takes into account the uncertainties of both proposed method, and experimental active and reactive MV power measurements. [ABSTRACT FROM PUBLISHER]

In this paper, a new solution is proposed for the remote monitoring and control of distributed generators (DGs) and energy storage systems (ESSs) connected to low-voltage distribution networks. The proposed system fulfills the in-force standard requirements for the connection of DGs to the utility grid. Moreover, it allows implementing some enhanced functions for the remote control of inverters of DGs and ESSs, not only in terms of disconnection but also in terms of voltage regulation and power shuttering. The proposed solution is based on a new interface protection system and a dedicated secondary substation concentrator, which allows the communication between the distributed system operator and the inverters of DGs or ESSs. The proposed system was tested on field in the electrical network of the island of Ustica. An experimental characterization was carried out to find the best communication conditions, i.e., the frequency band with the lowest noise and attenuation, considering the signal amplitude and signal-to-noise ratio constraints, as well as the desired transmission data rate and transfer time. [ABSTRACT FROM PUBLISHER]