Search

We report a microfluidic paper based analytical device implementing ion concentration polarization (ICP) for rapid pre-concentration of Escherichia coli in water. The fabricated device consists of a paper channel with a Nafion ® membrane and in-built micro wire electrodes to supply electric voltage to induce the ICP effect. E. coli cells were stained with SYTO 9 and fluorescence was used as a sensing method. The device achieved high concentration factor up to 2 × 10 5 within minutes. The effect of total ion concentration, on ICP and fluorescence intensity was studied. The reported device and method are suitable and effective for detection of E. coli during ballast water quality monitoring, coastal water quality monitoring where high salinity water is present., (© 2019 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

In this study, an internal circulation-anoxic/aerobic (IC-A/O) process followed by ultrafiltration (UF) and reverse osmosis (RO) system was applied for paper wastewater reclamation. The IC-AO system presented a stable and efficient performance, achieving high removal of chemical oxygen demand (COD), total organic carbon (TOC) and total nitrogen (TN) with methane production rate of 132.8 mL/d. Acute toxicity to Daphnia magna (D. magna) was reduced significantly (83.2%) and the spearman's rank correlation analysis indicated that the toxicity of effluents from each reactor were positively correlated with COD and TOC. Hexadecanoic acid, octadecanoic acid and benzophenone were the main toxic contributors for biological effluent. Microbial community revealed that Anaerolinea was significantly related with organic pollutants. The UF-RO system further removed pollutants and toxicity with the final effluent COD, TOC, ammonium nitrogen (NH 4 -N) and TN of 32.6, 18.8, 0.3 and 9.2 mg/L, respectively, which proved that it was feasible for paper wastewater reuse. This study presented an efficient, practical and environmentally competitive system, and paved a foundation for the treatment and reuse of paper wastewater.+ -N) and TN of 32.6, 18.8, 0.3 and 9.2 mg/L, respectively, which proved that it was feasible for paper wastewater reuse. This study presented an efficient, practical and environmentally competitive system, and paved a foundation for the treatment and reuse of paper wastewater., (Copyright © 2019 Elsevier B.V. All rights reserved.)

We have developed a new litmus paper test (DipTest) for detecting Escherichia coli (E. coli) in water samples by performing enzymatic reactions directly on the porous paper substrate. The paper strip consists of a long narrow piece of cellulose blotting paper coated with chemoattractant (at bottom edge), wax hydrophobic barrier (at the top edge), and custom formulated chemical reagents (at reaction zone immediately below the wax hydrophobic barrier). When the paper strip is dipped in water, E. coli in the water sample is attracted toward the paper strip due to a chemotaxic mechanism followed by the ascent along the paper strip toward the reaction zone due to a capillary wicking mechanism, and finally the capillary motion is arrested at the top edge of the paper strip by the hydrophobic barrier. The E. coli concentrated at the reaction zone of the paper strip will react with custom formulated chemical reagents to produce a pinkish-red color. Such a color change on the paper strip when dipped into water samples indicates the presence of E. coli contamination in potable water. The performance of the DipTest device has been checked with different known concentrations of E. coli contaminated water samples using different dip and wait times. The DipTest device has also been tested with different interfering bacteria and chemical contaminants. It has been observed that the different interfering contaminants do not have any impact on the DipTest, and it can become a potential solution for screening water samples for E. coli contamination at the point of source.

Cholera is now considered to be endemic in Haiti, often with increased incidence during rainy seasons. The challenge of cholera surveillance is exacerbated by the cost of sample collection and laboratory analysis. A diagnostic tool is needed that is low cost, easy-to-use, and able to detect and quantify Vibrio cholerae accurately in water samples within 18-24h, and perform reliably in remote settings lacking laboratory infrastructure and skilled staff. The two main objectives of this study were to develop and evaluate a new culture medium embedded in a new diagnostic tool (PAD for paper based analytical device) for detecting Vibrio cholerae from water samples collected in Haiti. The intent is to provide guidance for corrective action, such as chlorination, for water positive for V. cholerae epidemic strains. For detecting Vibrio cholerae, a new chromogenic medium was designed and evaluated as an alternative to thiosulfate citrate bile salts sucrose (TCBS) agar for testing raw water samples. Sensitivity and specificity of the medium were assessed using both raw and spiked water samples. The Vibrio cholerae chromogenic medium was proved to be highly selective against most of the cultivable bacteria in the water samples, without loss of sensitivity in detection of V. cholerae. Thus, reliability of this new culture medium for detection of V. cholerae in the presence of other Vibrio species in water samples offers a significant advantage. A new paper based device containing the new chromogenic medium previously evaluated was compared with reference methods for detecting V. cholerae from spiked water sample. The microbiological PAD specifications were evaluated in Haiti. More precisely, a total of 185 water samples were collected at five sites in Haiti, June 2014 and again in June 2015. With this new tool, three V. cholerae O1 and 17 V. cholerae non-O1/O139 strains were isolated. The presence of virulence-associated and regulatory genes, including ctxA, zot, ace, and toxR, was confirmed using multiplex PCR. The three V. cholerae O1 isolates were positive for three of the four virulence-associated and regulatory genes. Twelve of the V. cholerae non-O1/O139 isolates were found to carry toxR, but none were ctxA+, zot+, or ace+. However, six of the V. cholerae non-O1/O139 isolates were resistant to penicillin, ampicillin, trimethoprim/sulfamethoxazole, nalidixic acid, and ciprofloxacin. The paper based analytical device (PAD) provides advantages in that standard culture methods employing agar plates are not required. Also, intermediary isolation steps were not required, including transfer to selective growth media, hence these steps being omitted reduced time to results. Furthermore, experienced technical skills also were not required. Thus, PAD is well suited for resource-limited settings., (Copyright © 2016 Elsevier B.V. All rights reserved.)

This protocol describes rapid colorimetric detection of Escherichia coli, Salmonella spp., and Listeria monocytogenes from large volumes (10 L) of agricultural waters. Here, water is filtered through sterile Modified Moore Swabs (MMS), which consist of a simple gauze filter enclosed in a plastic cartridge, to concentrate bacteria. Following filtration, non-selective or selective enrichments for the target bacteria are performed in the MMS. For colorimetric detection of the target bacteria, the enrichments are then assayed using paper-based analytical devices (µPADs) embedded with bacteria-indicative substrates. Each substrate reacts with target-indicative bacterial enzymes, generating colored products that can be detected visually (qualitative detection) on the µPAD. Alternatively, digital images of the reacted µPADs can be generated with common scanning or photographic devices and analyzed using ImageJ software, allowing for more objective and standardized interpretation of results. Although the biochemical screening procedures are designed to identify the aforementioned bacterial pathogens, in some cases enzymes produced by background microbiota or the degradation of the colorimetric substrates may produce a false positive. Therefore, confirmation using a more discriminatory diagnostic is needed. Nonetheless, this bacterial concentration and detection platform is inexpensive, sensitive (0.1 CFU/ml detection limit), easy to perform, and rapid (concentration, enrichment, and detection are performed within approximately 24 hr), justifying its use as an initial screening method for the microbiological quality of agricultural water.

Paper chips for immunoassay were patterned by screen printing of polydimethylsiloxane (PDMS) or wax pencil drawing. The methods for paper chip patterning are cheap, convenient, rapid and suitable for most laboratories. The whole time for patterning a paper chip is no more than 10 min. Visible immunoassay for the detection of bacteria (Escherichia coli ) has been realized using the paper chip, on which the antibody for capturing E. Coli was immobilized on the detection zones of the paper chip, while the detection antibody was labeled with gold nanoparticles (AuNPs) as a signal reporter. After an immunological reaction, the AuNPs bound on the paper chip can effectively catalyse the reduction of silver ions during the silver enhancing step, generating a visible result that can be read by naked eyes. The quantitative results can be acquired by scanning the silver stained paper chip with a commercial scanner/or digital camera. The density of E. coli in water samples can be measured after calibrating the gray value of silver stained spots with the logarithmic number of bacteria. The time and reagents consumed on the paper chip immunoassay is much smaller than those of conventional ELISA, while the sensitivity of the paper chip immunoassay is comparable to conventional ELISA. The technology proposed in this work displays a great potential in the in-situ analysis when daily monitoring of water quality are required., (© 2013 Published by Elsevier B.V.)

Identifying the source and the distribution of bacterial contaminant communities in water circuits of industrial applications is critical even when the process may not show signs of acute biofouling. The endemic contamination of facilities can cause adverse effects on process runability but may be masked by the observed daily variability. The distribution of background communities of bacterial contaminants may therefore be critical in the development of new site-specific antifouling strategies. In a paper mill as one example for a full-scale production process, bacterial contaminants in process water and pulp suspensions were mapped using molecular fingerprints at representative locations throughout the plant. These ecological data were analyzed in the process-engineering context of pulp and water flow in the facilities. Dispersal limits within the plant environment led to the presence of distinct groups of contaminant communities in the primary units of the plant, despite high flows of water and paper pulp between units. In the paper machine circuit, community profiles were more homogeneous than in the other primary units. The variability between sampled communities in each primary unit was used to identify a possible point source of microbial contamination, in this case a storage silo for reused pulp. Part of the contamination problem in the paper mill is likely related to indirect effects of microbial activity under the local conditions in the silo rather than to the direct presence of accumulated microbial biomass.

The antifouling potential of electric polarization combined and not combined with biocides was studied in nonsaline warm water with high organic content. Deinococcus geothermalis is a bacterium known for forming colored biofilms in paper machines and for its persistence against cleaning and chemical treatments. When D. geothermalis biofilms grown for 24 h in simulated paper machine water were exposed to cathodic or cathodically weighted pulsed polarization at least 60% (P < 0.05) of the biofilms were removed from stainless steel (AISI 316L). Biofilm removal by 25 ppm (effective substances 5-25 ppm) of oxidizing biocides (bromochloro-5,5-dimethylhydantoin, 2,2-dibromo-2-cyanoacetamide, peracetic acid) increased to 70% when combined with cathodically weighted pulsed polarization. Using a novel instrument that allows real-time detection of reactive oxygen species (ROS) we showed that the polarization program effective in antifouling generated ROS in a pulsed manner on the steel surface. We thus suggest that the observed added value of oxidative biocides combined with polarization depended on ROS. This suggestion was supported by the finding that a reductive biocide, methylene bisthiocyanate, counteracted the antifouling effect of polarization.

Forty-one bacterial strains isolated from the headbox water of two machines in a Canadian paper mill were associated with the genera Asticcacaulis, Acidovorax, Bacillus, Exiguobacterium, Hydrogenophaga, Pseudomonas, Pseudoxanthomonas, Staphylococcus, Stenotrophomonas based on the sequence of their 16S rRNA genes. The metabolic profile of these strains were determined using Biolog EcoPlate, and the bacteria were divided into four metabolic groups. Metabolic profiles of the bacterial communities colonizing the headbox water of two paper machines was also determined weekly over a 1 year period. The only compound that was not reduced by the bacterial community was 2-hydroxybenzoic acid. Utilization frequency of the other carbon sources in the Biolog EcoPlate ranged from 3 to 100%. The metabolic profiles of the bacterial community did not vary considerably between the two paper machines. However, the metabolic profile varied among the sampling dates.

A Gram-positive, non-motile, rod-shaped, non-spore-forming bacterium, designated CAAS 251T, was isolated from paper-mill effluent in Wuhan, China. The organism grew optimally at 40-42 degrees C and at pH 9.0-10.0. The major menaquinones were MK-7, MK-8 and MK-9. The predominant cellular fatty acids were anteiso-C15:0 (34.78 %), anteiso-C17:0 (25.24 %) and C16:0 (13.37 %). The G+C content of the genomic DNA was 65.5 mol%. A phylogenetic analysis based on 16S rRNA gene sequences showed that strain CAAS 251T belongs to the genus Nesterenkonia, having sequence identities ranging from 96.0 to 97.0 % with respect to eight recognized species of the genus Nesterenkonia. Data from DNA-DNA hybridization and physiological and biochemical tests indicated that strain CAAS 251T represents a novel species of the genus Nesterenkonia, for which the name Nesterenkonia flava sp. nov. is proposed. The type strain is CAAS 251T (=CCTCC AB 207010T=JCM 14814T).

Biosolids produced from pulp and paper mill wastewater treatment have excellent properties as soil conditioners, but often contain high levels of Escherichia coli. E. coli are commonly used as indicators of fecal contamination and health hazard; therefore, their presence in biosolids causes concern and has lead to restrictions in land-spreading. The objectives of this study were to determine the following: (1) if E. coli from the biosolids of a wastewater-free pulp and paper mill were enteric pathogens, and (2) if other waterborne microbial pathogens were present. E. coli were screened for heat-labile and heat-stable enterotoxin and verocytotoxin virulence genes using a polymerase chain reaction. Ten isolates were also screened for invasion-associated locus and invasion plasmid antigen H genes. None of the 120 isolates carried these genes. Tests for seven other microbial pathogens were negative. Effluents and biosolids from this mill do not contain common microbial pathogens and are unlikely to pose a health hazard.

A microorganism degrading 2,4-dichlorophenol isolated from an aeration pond of the Baikal Pulp and Paper Mill was identified as Bacillus cereus BIP507 based on morphological and physiological characters as well as 16s rDNA sequencing. This microorganism proved able to degrade high 2,4-dichlorophenol concentrations (up to 560 microM).

The metagenomic DNA of pulp sediments from paper mill effluent was extracted and purified. The 16S rDNA was amplified using the purified metagenomic DNA as template and a 16S rDNA library was prepared. Sequence analysis of 16S rDNA clones showed that diverse of uncultured bacteria inhabit in this environment, which can be classified into 4 clusters as Spirochaetes, Proteobacteria, Bacteroidetes and Firmicutes. A metagenomic library containing 10000 clones was constructed into cosmid vector, and the capacity of inserted DNA of which was 3.53 x 10(8) bp. Functional screening of the library resulted in isolation of two independent clones expressing endoglucanase activity, three independent clones expressing exoglucanase activity and two independent clones expressing beta-glucosidase activity. One clone expressing strongest enzyme activity from each activity category was chosen to be further analyzed. Three novel cellulase genes designated as umcel5L, umcel5M and umbgl3D were identified by subcloning, sequencing and expression. The umcel5L encodes an endoglucanase belonging to glycosyl hydrolase family 5, which is most related to an endoglucanase from Bradyrhizobium japonicum at 43% identity and 59% similarity. The umcel5M encodes a cellodextrinase belonging to glycosyl hydrolase family 5, which is most similar to a cellodextrinase from Fibrobacter succinogenes at 48% identity and 69% similarity. The umbgl3D encodes a putative beta-glucosidase belonging to glycosyl hydrolase family 3, which shares highest homology with a beta-glucosidase from Thermotoga maritima at 46% identity and 61% similarity. It is the first time to reveal the bacterial diversity of pulp sediments from paper mill effluent and clone novel cellulase genes from the bacteria by culture-independent method.

Wood pulping and paper production generate a considerable amount of wastewater, containing many pollutants among them resin and fatty acids. Resin acids contribute substantially to effluent toxicity and were identified to be detrimental to microorganisms of activated sludge and in particular to bacteria in anaerobic wastewater treatment system and other forms of aquatic life. The objective of the present study was to check the applicability of the ozone and advanced oxidation processes (AOPs) to eliminate resin acids from aqueous solutions and to determine the ozone dose required. Furthermore, an investigation of the influence of the oxidation methods on subsequent biological destruction of the byproducts was performed. Aqueous solution of the resin acids: abietic, dehydroabietic and isopimaric acids with different initial composition were subjected to ozonation or AOP processes at different ozone doses. After ozonation or advanced oxidation pretreatment the model solutions were biodegraded in aerated vessels containing activated sludge. During ozonation of the resin acids aqueous solutions the resin acids were almost eliminated, however the reduction of chemical oxygen demand (COD) was rather low. The ozone dose required to obtain reduction of resin acids >90% was in the range of 0.1-0.7mgO(3)/mgCOD, depending on the composition and concentration of model solutions. The toxicity of ozonated resin acids solutions decreased with increasing applied ozone dose up to about 0.3-0.5mgO(3)/mgCOD, thereafter increased. Ozonation and other AOP processes did not increase the rate of biodegradation of resin acids model solutions in aerated activated sludge systems compared to not pretreated solutions.

The seasonal physico-chemical and microbial quality of Gola river water has been analyzed after confluence of pulp paper mill waste. The study revealed that it has enhanced 20-30 times pollution load of BOD, COD, TDS, TSS, sulphate, chloride, sodium, nitrate, potassium, lignin and phenol after mixing of pulp paper mill waste with river water in all season. Further, it induced the bacterial growth by increasing most probable number value of E. coli was 1.57 x 10(4), 1.6 x 10(4), 1.37 x 10(4) and SPC count was 1.68 x 10(4), 1.64 x 10(4), 1.67 x 10(4)/100 ml during summer, monsoon, winter respectively. While the most probable number value in river water before mixing of pulp paper mill waste was 1.4 x 10(2), 1.82 x 10(2), 1.5 x 10(2) and SPC count was 2.8 x 10(3), 2.89 x 10(3), 2.78 x 10(3)/100 ml during summer, monsoon and winter respectively. This indicated from 88-114 fold increase in most probable number value of E. coli and 56.55-60.0 times increase in SPC count of river water after mixing of effluent in summer, monsoon and winter. Moreover, the most probable number value in effluent itself before mixing was 3.4 x 10(2), 3.3 x 10(2), 2.8 x 10(2) and SPC count was 6 x 10(4), 6.5 x 10(4), 6 x 10(4)/100 ml during summer, monsoon, winter, respectively. Furthermore, it was revealed that the seasonal variation also regulated the bacterial population dynamics as per the physico-chemical quality, in which E. coli was found highest at the rate of (5.9 x 10(4)), E. aerogenes (5.3 x 10(4)), P. aeruginosa (1.3 x 10(4)), S. aureus (3.2 x 10(3)), K. pneumoniae (2.6 x 10(4)), Enteritidis (1.1 x 10(4)) on monsoon season and V. cholerae (7.4 x 10(2)), V. vulnificus (9.2 x 10(2))/100 ml in river water when contaminated with pulp paper mill waste in monsoon season. Thus, the monsoon season showed presence of FC and TC indicated the thermo-tolerant and disease causing group of bacterial population in effluent and its sequence was observed as monsoon>summer>winter. This indicated the growth of many pathogenic and non-pathogenic bacteria for health hazards with contamination of pulp paper waste in aquatic ecosystem within the vicinity of pulp paper mill industry.

The aim of this study was to characterize the actinobacterial population present in pulps and boards containing recycled fibres. A total of 107 isolates was identified on the basis of their pigmentation, morphological properties, fatty acid profiles and growth temperature. Of the wet pulp and water sample isolates (n=87), 74.7% belonged to the genus Streptomyces, 17.2% to Nocardiopsis and 8.0% to thermoactinomycetes, whereas all the board sample isolates (n=20) were thermoactinomycetes. The identification of 53 isolates was continued by molecular methods. Partial 16S rDNA sequencing and automated ribotyping divided the Streptomyces isolates (n=31) into 14 different taxa. The most common streptomycetes were the mesophilic S. albidoflavus and moderately thermophilic S. thermocarboxydus. The Nocardiopsis isolates (n=11) belonged to six different taxa, whereas the thermoactinomycetes were mainly members of the species Laceyella sacchari (formerly Thermoactinomyces sacchari). The results indicated the probable presence of one or more new species within each of these genera. Obviously, the drying stage used in the board making processes had eliminated all members of the species Streptomyces and Nocardiopsis present in the wet recycled fibre pulp samples. Only the thermotolerant endospores of L. sacchari were still present in the final products. The potential of automated ribotyping for identifying actinobacteria was indicated, as soon as comprehensive identification libraries became available.

Kraft mill effluents were biologically treated in an aerated lagoon (AL) (3.4 L) to evaluate the behavior of aromatic compounds by UV-vis spectroscopy. Under aerobic conditions, biological oxygen demand (BOD(5)) removal was between 84% and 95%, whereas soluble chemical oxygen demand (COD(s)) removal ranged between 40% and 60%. A slight increase was observed in the VIS(436)/COD(s) relationship (0.101-0.110), indicating that color reduction was less than the total organic matter reduction expressed by COD(s). Additionally, low values of UV(254)/UV(280) (1.23-1.12) indicate the presence of lignin-derived compounds in the aerobic effluent relationship. Ultrafiltration (UF) analysis shows that color was concentrated in the molecular weight fraction larger than 10,000 Da. The recalcitrant fraction was found to be resistant to further biodegradation, even under optimized microbiological conditions.

Bacterial community compositions from 10 pulp- and paper-mill treatment systems were compared using both traditional and molecular techniques. 16S-RFLP (Random Fragment Length Polymorphisms) analysis was used to examine the genotypic profiles of the whole bacterial community of each treatment system. Although all the communities shared approximately 60% of their DNA band pattern, as determined by computer-assisted cluster analysis, each community displayed a unique profile that was stable over time under normal operating parameters. Reverse Sample Genome Probing (RSGP) and 16S-RFLP were used to compare the culturable bacterial communities of several geographically separated pulp-mill biotreatment system communities. There was little overlap in the composition of the culturable community between mills at the genus level. Furthermore, RSGP variation was almost as high within a mill as between mills. Partial sequences of the 16S rRNA genes from culturable isolates identified Bacillus spp., Pseudomonas spp., and Xanthobacter as some of the dominant species. Finally, several 16S rRNA genes from two whole community 16S RNA gene libraries were partially sequenced and identified as similar to unknown alpha-, beta-, and gamma-Proteobacteria, Ralstonia, Alcaligenes, Nitrospira, Firmicutes, and clones representing the new Holophaga/Acidobacterium phylum. These findings suggest that although these pulp- and paper-mill biotreatment communities perform similar functions, they are populated by unique mixtures of species.

Currently, very little is known about the normal dynamics of microbial populations in wastewater treatment systems and the relationship between population dynamics and functional stability of treatment systems. We monitored the bacterial community in an oxygen activated sludge system at a pulp and paper mill during a 55-day period that included normal operation as well as an 11-day shutdown of the system and the subsequent start-up. Ribosomal intergenic spacer (RIS) length polymorphism fingerprints were very similar (57-88% similar) throughout the study period. Analysis of clone libraries of RIS-rRNA gene amplicons indicated that Proteobacteria affiliated with the genera Paracraurococcus and Acidovorax as well as a Green Nonsulfur Bacterium affiliated with the genus Roseiflexus were consistently among predominant members of the community. By comparison, wastewater treatment systems from different pulp mills yielded dissimilar fingerprints (9-17% similar), and their clone libraries had distinct predominant phylotypes. Our analysis strongly suggests that the composition of the bacterial community in the former treatment system was stable during normal operation as well as the shutdown and start-up. This stability coincided with functional stability, including consistent and nearly complete removal of biological oxygen demand.

Anaerobic biodegradation of fermented spent sulphite liquor, SSL, which is produced during the manufacture of sulphite pulp, was investigated. SSL contains a high concentration of lignin products in addition to hemicellulose and has a very high COD load (173 g COD l(-1)). Batch experiments with diluted SSL and pretreated SSL indicated a potential of 12-22 l methane per litre SSL, which corresponds to 0.13-0.22 l methane (g VS)(-1) and COD removal of up to 37%. COD removal in a mesophilic upflow anaerobic sludge blanket, UASB. reactor ranged from 10% to 31% at an organic loading rate, OLR, of 10-51 g (1 d)(-1) and hydraulic retention time from 3.7 to 1.5 days. The biogas productivity was 3 1 (l(reactor d)(-1), with a yield of 0.05 l gas (g VS)(-1). These results suggest that anaerobic digestion in UASB reactors may provide a new alternative for the treatment of SSL to other treatment strategies such as incineration. Although the total COD reduction achieved is limited, bioenergy is produced and readily biodegradable matter is removed causing less load on post-treatment installations.

After isolation from a pulp mill wastewater treatment facility, two yeast strains, designated SPT1 and SPT2, were characterized and used in the development of mediated biochemical oxygen demand (BOD) biosensors for wastewater. 18S rRNA gene sequence analysis revealed a one nucleotide difference between the sequence of SPT1 and those of Candida sojae and Candida viswanthii. While SPT2 had the highest overall homology to Pichia norvegensis, at only 73.5%, it is clearly an ascomycete, based on BLAST comparisons and phylogenetic analyses. Neighbor-joining dendrograms indicated that SPT1 clustered with several Candida spp., and that SPT2 clustered with Starmera spp., albeit as a very deep branch. Physiological tests, microscopic observations, and fatty acid analysis confirmed that SPT1 and SPT2 are novel yeast strains. Physiological tests also indicated that both strains had potential for use in mediated biosensors for estimation of BOD in wastewater. The lower detection limits of SPT1- and SPT2-based K3Fe(CN)6-mediated biosensors for a pulp-mill effluent were 2 and 1 mg BOD/L, respectively. Biosensor-response times for effluents from eight different pulp mills were in the range of 5 min. Reliability and sensitivity of the SPT1- and SPT2-based biosensors were good, but varied with the wastewater.

Paper machine biofilms formed in situ on stainless steel surfaces were studied. A robust flow cell was fitted to side stream (1.8 m s(-1)) of the spray water circuit of a paper machine. This on-site tool allowed for assessing the efficacy of antifoulants and the adequacy of steel polishing under mill conditions. A rapid fluorescence-based assay was developed to quantify the biomass of shallow biofilms on machine steel. The fluorescence matched the ATP content measured for the same biofilms. Electrolytic polishing reduced the tendency of biofouling of 500 grit surface steel. Biofilm grew under machine conditions as clusters on the steels, showing uniformly coccoid, filaments or short rods; only one cell type in each cluster. The biofilm clusters excluded latex beads of 0.02 microm with hydrophilic or with hydrophobic surfaces from penetrating more than three to four layers of cells. Under the high hydraulic flow at the machine (1.8 m s(-1)), the biofilm grew in 7 days 6-10 microm thick. The high flow rate guided the shape of the biofilm clusters emerging after the primary attachment of cells. Adhered individual bacteria were the platform on steel to which solids such as paper machine fines then accumulated.

Pulp and paper secondary waste-treatment systems in Brazil, Canada, New Zealand, and the U.S.A. contained dynamic cyanobacterial communities, some of which exceeded heterotrophic bacterial biomass. No other viable photoautotrophic populations were detected in the ponds. Regardless of geographical location, Oscillatoriales including Phormidium, Geitlerinema, and Pseudanabaena were the dominant taxa. As well, Chroococcus (Chroococcales) was an important genus in Brazil and New Zealand. The possible impact of cyanobacteria on waste-treatment efficiency deserves further study given their large biomass and diverse metabolic characteristics.

Two new yeast strains (SPT1 and SPT2) were isolated and immobilized on glassy carbon electrodes to form microbial biosensors for estimation of biochemical oxygen demand (BOD). Ferricyanide was proven to be the most efficient mediator to shuttle electrons from the redox center of reduced microbial enzymes to the electrode in the presence of excess glucose/glutamic acid (GGA). With a 3-fold greater metabolic assimilation capability and greater responses to various effluent samples, SPT1 was selected for sensor-BOD measurements. BOD estimations for the GGA standard resulted in an extended linear range: 2-100 mg/l. Response reproducibility was +/-10% for a GGA standard containing 10 mg BOD/l. For analysis of pulp mill effluents, the BOD detection limit was 2 mg/l with a response time of 5 min.

Formation of fouling deposits is a serious problem facing paper mills. Despite the search for alternative methods, chemical biocides still represent the chief countermeasure to control microbial growth and general fouling buid-up in pulp and paper mills. The purpose of this work was to determine the effect of two biocides (carbamate and glutaraldehyde) on both planktonic cells and fouling layers of a paper machine system. A flow system was used for the study of fouling accumulation in an industrial white water circuit. Both biocides proved to be more effective in reducing the microbial loading of the white water circuit than the deposit accumulated on the stainless steel surfaces. Carbamate, in contrast to glutaraldehyde, had the ability of promoting cell agglomeration since the microbial loading decreased much more when the white water, treated with carbamate, was filtered through a filter-linen. The retention of suspended cells in the cellulose fibres acquires major importance since it is obtained by using an already existing physical process (filtration), which strongly enhances the overall microbial reduction obtained with the addition of the carbamate, without increasing the economic costs. These results also suggest that the use of conventional retention agents in pulp and paper processes can be efficient in controlling unwanted microbial effects.

Coliform bacteria have long been used to indicate fecal contamination of water and thus a health hazard. In this study, the in-mill water and external effluent treatment systems of seven typical Canadian pulp and paper mills were all shown to support the growth of numerous coliforms, especially Klebsiella Spp., Escherichia coli. Enterobacter spp., and Citrobacter spp. In all mills and most sampled locations, klebsiellas were the predominant coliforms. Although all but one of the mills had no sewage input and most disinfected their feed (input) water, all contained the most typical fecal indicator bacterium, E. coli. Many of the mill coliforms were classified as fecal coliforms by standard "MPN" and metabolic tests, but this was shown to be due to their thermotolerance, not their origin. Mill coliforms were shown not to be just simple transients from feedwater or furnish (wood), but to be continuously growing, especially in some of the primary clarifiers. Isolated mill coliforms grew very well on a sterilized raw combined mill effluent. The fecal streptococci (enterococci), alternative indicators of fecal health hazards, were common in all mills in the absence of sewage. Ten strains of E. coli isolated from four mills were all shown to be non-toxigenic strains of harmless serotypes. No salmonellas were found. Therefore, the use of total coliform, fecal coliform, enterococci, or E. coli counts as indicators of fecal contamination, and thus of health hazard in pulp and paper mill effluents or biosolids (sludges) known to be free of fecal input is invalid.

The manufacture of paper generates significant quantities of wastewater; as high as 60 m3/tonne of paper produced. The raw wastewaters from paper and board mills can be potentially very polluting. Indeed, a recent survey within the UK industry has found that their chemical oxygen demands can be as high as 11000 mg/l. This paper reviews the processes involved in paper making and examines the effects which they could have on the environment. It also evaluates the treatment processes which are used to minimise these effects. In line with the majority of UK practice, it focuses mainly on aerobic biological treatment and, in particular, on the activated sludge process. This means that there is an in-depth discussion about the problems associated with filamentous bacteria and sludge "bulking". The paper also discusses the way in which anaerobic digestion can be applied to the treatment of liquid wastes from the manufacture of paper.

The majority of pulp and paper mills now biotreat their combined effluents using activated sludge. On the assumption that their wood-based effluents have negligible fixed N, and that activated-sludge microorganisms will not fix significant N, these mills routinely spend large amounts adding ammonia or urea to their aeration tanks (bioreactors) to permit normal biomass growth. N(2) fixation in seven Eastern Canadian pulp and paper mill effluent treatment systems was analyzed using acetylene reduction assays, quantitative nitrogenase (nifH) gene probing, and bacterial isolations. In situ N(2) fixation was undetectable in all seven bioreactors but was present in six associated primary clarifiers. One primary clarifier was studied in greater detail. Approximately 50% of all culturable cells in the clarifier contained nifH, of which >90% were Klebsiella strains. All primary-clarifier coliform bacteria growing on MacConkey agar were identified as klebsiellas, and all those probed contained nifH. In contrast, analysis of 48 random coliform isolates from other mill water system locations showed that only 24 (50%) possessed the nifH gene, and only 13 (27%) showed inducible N(2)-fixing activity. Thus, all the pulp and paper mill primary clarifiers tested appeared to be sites of active N(2) fixation (0.87 to 4.90 mg of N liter(-1) day(-1)) and a microbial community strongly biased toward this activity. This may also explain why coliform bacteria, especially klebsiellas, are indigenous in pulp and paper mill water systems.

Resin acids, a group of diterpenoid carboxylic acids present mainly in softwood species, are present in many pulp mill effluents and toxic to fish in recipient waters. They are considered to be readily biodegradable. However, their removal across biological treatment systems has been shown to vary. Recent studies indicate that natural resin acids and transformation products may accumulate in sediments and pose acute and chronic toxicity to fish. Several resin acid biotransformation compounds have also been shown to bioaccumulate and to be more resistant to biodegradation than the original material. Until recently, the microbiology of resin-acid degradation has received only scant attention. Although wood-inhabiting fungi have been shown to decrease the level of resin present in wood, there is no conclusive evidence that fungi can completely degrade these compounds. In contrast, a number of bacterial isolates have recently been described which are able to utilize dehydroabietic or isopimaric acids as their sole carbon source. There appears to be an unusually high degree of substrate specificity with respect of the utilization of abietane congeners and the presence of substituents. Pimaranes do not appear to be attacked to the same extent as the abietanes. This paper reviews the occurrence, chemistry, toxicity, and biodegradation of resin acids in relation to the biological treatment of pulp and paper mill effluents.

We investigated resin acid degradation in five bacteria isolated from a bleach kraft mill effluent enrichment. All of the bacteria grew on dehydroabietic acid (DHA), a resin acid routinely detected in pulping effluents, or glycerol as the sole carbon source. None of the strains grew on acetate or methanol. Glycerol-grown, high-density, resting-cell suspensions were found to undergo a lag for 2 to 4 h before DHA degradation commenced, suggesting that this activity was inducible. This was further investigated by spiking similar cultures with tetracycline, a protein synthesis inhibitor, at various times during the DHA disappearance curve. Cultures to which the antibiotic was added prior to the lag did not degrade DHA. Those that were spiked with the antibiotic after the lag phase (4 h) degraded DHA at the same rate as did controls with no added tetracycline. Therefore, de novo protein synthesis was required for DHA biodegradation, confirming that this activity is inducible. The five strains were also evaluated for their ability to degrade other resin acids. All strains behaved in a similar fashion. Unchlorinated abietane-type resin acids (abietic acid, DHA, and 7-oxo-DHA) were completely degraded within 7 days, whereas pimarane resin acids (sandaracopimaric acid, isopimaric acid, and pimaric acid) were poorly degraded (25% or less). Chlorination of DHA affected biodegradation, with both 12,14-dichloro-DHA and 14-chloro-DHA showing resistance to degradation. However, 50 to 60% of the 12-chloro-DHA was consumed within the same period.

As a supplement to a preceding paper (Zbl. Hyg., 194 (1993). 369-279) the resistance of bioindicators has been investigated which differed only in the material of which the carriers are made (filter paper and glass fibre fleece, respectively). The conditions of the tests were such that further evidence could be expected for the fact that the characteristic values of bioindicators can be falsified by superheating of the carrier and its envelope. As a test organism Enterococcus faecium has been used. To avoid side effects, the bacteria have been dried on to the carriers from a suspension in water distillators. The exposition basket of the resistometer has been loaded with 3 rows of 15 indicators (disc shaped; diameter: 6 mm), arranged parallel. At a temperature of 68 degrees C the dependency of (relative) frequency of indicators having surviving test organisms capable of multiplying on exposure time to saturated steam has been determined. Free exposed indicators made of filter paper required considerably longer exposure periods than indicators made of glass fibre fleece to change from "(nearly) all the indicators have test organisms capable of multiplying" to "(nearly) all the indicators are free from test organisms capable of multiplying". The exposure time to free 50% of carriers made of filter paper from test organisms capable of multiplying (t50%) amounted to 44.1 minutes. The frequency of indicators free from test organisms was higher at the ends than in the middle of the exposed rows. When such indicators had been wetted before exposure, they showed a t50% value of 2.3 minutes, and the frequency of indicators free from surviving test organisms was distributed over the exposed indicators evenly. Free exposed indicators made of glass fibre fleece showed a t50% value of 4.4 minutes. The frequency of indicators free from test organisms was evenly distributed. Wetting of the indicators before exposure changed t50% value only slightly. When indicators made of glass fibre fleece had been exposed between two layers of filter paper they showed a very high t50% value (47.5 minutes), and the frequency of indicators free from test organisms was unevenly distributed. Indicators being sterile could be found mainly at the ends of the exposed rows. In an envelope of parchment paper bioindicators made of glass fibre fleece showed considerably higher characteristic values than when free exposed. Superheating of the carriers amounted to about 3 Kelvin.(ABSTRACT TRUNCATED AT 400 WORDS)

Water samples from the wastewater treatment system of a bleach kraft mill and from the river that supplies the mill were plated on six different media and culturable isolates were screened for substrate utilization patterns, taxonomic characters, plasmid content, and resistance to ampicillin, streptomycin, kanamycin, tetracycline, naldixic acid, mercury, nickel, copper, cobalt, cadmium, and zinc. A cluster analysis of the substrate utilization profiles and taxonomic characters revealed that Pseudomonas, Acinetobacter, and Acidovorax spp. were common among the culturable isolates from the river, while Ancylobacter aquaticus, Klebsiella spp., and an unknown group of pleomorphic Gram-negative methylotrophs were common among the culturable isolates from the mill treatment system. Of isolates from the settling pond and aerated lagoon, 78 and 64% carried plasmids, while only 56% of isolates from the river carried plasmids. Plasmids were significantly associated with resistance to cadmium but not with any other resistance characters. Large numbers of plasmid-carrying A. aquaticus strains and pleomorphic methylotrophs accounted for high plasmid incidence levels in the mill treatment system, and the ability to dechlorinate simple aliphatic substrates was found in these two groups as well as in one Pseudomonas strain.

Three pulp and paper mill processing plants were evaluated for fecal coliform and Klebsiella pneumoniae bacterial concentrations. Freshwater consumed by paper industries contained minimum detectable levels of K. pneumoniae, less than 10 organisms per 100 ml. Elevated concentrations of K. pneumoniae could be traced from early pulping stages to water processing reuse systems. Concentrations of K. pneumoniae (thermotolerant and thermointolerant) ranged from 40,000 organisms per 100 ml to an estimated 3 x 10(6) organisms per 100 ml. K. pneumoniae biotyping provided evidence for the selective growth and persistence of K. pneumoniae from the initial wood washing stages through to the final effluent discharge. Wastewater treatment had limited effects in reducing K. pneumoniae concentrations. K. pneumoniae levels ranged from 40 organisms per 100 ml to an estimated 10(6) organisms per 100 ml. The presence of K. pneumoniae in water indicates degraded water quality, and its significance with regard to human health effects has yet to be examined.

Wisconsin pulp and paper mill processing plants were evaluated for fecal coliform and total Klebsiella (i.e., thermotolerant and thermointolerant) bacterial concentrations. Using the standard fecal coliform test, up to 90 per cent of non-fecal source thermotolerant K. pneumoniae was falsely identified as fecal source bacteria. Since there is a lack of specificity in the currently used standard for fecal coliform evaluation, a more reliable health risk assessment for fecal coliform bacteria is recommended.

We investigated survival of Klebsiella pneumoniae in freshwater, by determining bacterial densities at eight temperatures between 0 and 20 degrees C at various distances from the discharge area in a lake receiving bacteria mainly from a paper mill. An mFC-inositol-carbenicillin-agar medium was used for Klebsiella enumeration by the membrane filter method. About 90% of the bacteria forming typical colonies on this medium were identified as Klebsiella species. About 10% of the bacteria were false positive, and, an equal percentage were false negative. Semilogarithmic plots of bacterial densities as a function of distance were found to be linear, with slopes depending on water temperature. The average velocity of the flow was estimated from the travel-of-bacterial-density minima caused by production stops. Regression equations were calculated for the dependence of death rate on temperature alone and on both temperature and discharge. The temperature coefficient (Q10) of the death rate was estimated to be 2.1 +/- 0.4. The decimal reduction time (T90) of K. pneumoniae at 0 degrees C was calculated to be about 24 days, and that at 20 degrees C was slightly over 5 days. The regression model was verified by independent observations. Factors affecting the reliability of the estimates were evaluated.

Variations in the numbers of total colonies of Klebsiella pneumoniae, Acinetobacter spp. and pseudomonads were investigated in process waters of a paper mill in southern Finland. Variations were related to independent parameters, namely temperature, pH, redox potential and production of offset paper, by using multiple regression analysis. Temperature was the most significant regressor variable and was negatively correlated with bacterial counts. It accounted for up to about 80% of the variance in bacterial counts in various parts of the process. The significance of temperature was due to its fluctuations in a critical range, above and below the maxima for bacterial growth. The pH level was also significant for total colony count and for K. pneumoniae. Redox potential and the production of offset paper were of significance for Acinetobacter spp. Washing the paper machine with water and lye decreased the numbers of bacteria in process waters.

The coliform flora of a pulp and cardboard mill that uses birch as the raw material and ammonium sulphate as the process chemical was studied. Escherichia coli was observed to multiply in the mill. It persisted as the dominant thermotolerant coliform in the effluent. Klebsiellae were encountered among total coliforms only. The E. coli strains isolated had the biochemical characteristics and maximum growth temperatures typical to the species. However, serotyping and hemolysin test differentiated these strains from pathogenic and fecal E. coli.