Search

Pollution problems are increasingly becoming e a priority issue from both scientific and technological points of view. The dispersion and frequency of pollutants in the environment are on the rise, leading to the emergence have been increasing, including of a new class of contaminants that not only impact the environment but also pose risks to people's health. Therefore, developing new methods for identifying and quantifying these pollutants classified as emerging contaminants is imperative. These methods enable regulatory actions that effectively minimize their adverse effects to take steps to regulate and reduce their impact. On the other hand, these new contaminants represent a challenge for current technologies to be adapted to control and remove emerging contaminants and involve innovative, eco-friendly, and sustainable remediation technologies. There is a vast amount of information collected in this review on emerging pollutants, comparing the identification and quantification methods, the technologies applied for their control and remediation, and the policies and regulations necessary for their operation and application. In addition, This review will deal with different aspects of emerging contaminants, their origin, nature, detection, and treatment concerning water and wastewater., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Ltd. All rights reserved.)

Herein, the synthesis, characterization, and adsorption performance of a novel green sulfur-doped carbon nanosphere (S-CNs) is studied to eliminate Cd (II) ions from water effectively. S-CNs were characterized using different techniques including Raman spectroscopy, powder X-ray diffraction (PXRD), scanning electron microscopy (SEM) with energy dispersive X-ray analysis (EDX), , Brunauer-Emmett-Teller (BET) specific surface area analysis and Fourier transform infrared spectrophotometry (FT-IR), were performed. The efficient adsorption of the Cd (II) ions onto S-CNs strongly depended on pH, initial concentration of Cd (II) ions, S-CNs dosage, and temperature. Four isotherm models (Langmuir, Freundlich, Temkin & Redlich Peterson) were tested for modeling. Out of four, Langmuir showed more applicability than the other three models, with a Q max value of 242.72 mg/g. Kinetic modeling studies suggest a superior fit of the obtained experimental data with the Elovich equation (linear) and pseudo-second-order (non-linear) rather than other linear and non-linear models. Data obtained from thermodynamic modeling indicates that using S-CNs for Cd (II) ions adsorption is a spontaneous and endothermic . The current work recommends using better and recyclable S-CNs to uptake excess Cd (II) ions., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Ltd. All rights reserved.)

Chemical co-precipitation synthesized novel and green cobalt-oxide nanoparticles (Co 3 O 4 -NPs) utilizing cobalt nitrate as cobalt precursors. FTIR, Raman, scanning electron microscopy, UV visible, X-ray powder diffraction, and BET was used to analyze the surface characteristics, composition, and morphology, of the NPs. These green Co 3 O 4 -NPs were employed to remove Pb ions from simulated wastewater solutions at various pH, adsorbate, temperature, and dose concentrations. At dose 20 mg/L, pH 6.0, 20 mg/L (Pb(II) solution, 25 °C of temperature, and 45 min for equilibrium, nearly 99.44% of Pb ions were removed. To evaluate the kinetic data, four different kinetic equations were used. The data fit the Elovich rate equation better than the other three models. Thermodynamic and isothermal studies were also evaluated, and the maximum adsorption capacity of 450.45 mg/g was observed at 298.15 K. 0.1 M HNO 3, and 0.1 HCl were used to regenerate used Co 3 O 4 -NPs. Simulation results show the strong correlation of the Co atom in the Co 3 O 4 -NPs generates active delocalized surface states, which are energetically most favorable for heavy metal (Pb ions) adsorption and removal, supporting the experimental outcomes. In concluding remarks, green Co 3 O 4 -NPs can also be used as an adsorbent to remove Pb ions from wastewater bodies., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Inc. All rights reserved.)

Artemisia absinthium leaves were utilized as a reducing agent for green synthesis of Zinc oxide nanoparticles (particle size 17 nm). Synthesized green-ZnO (g-ZnO) were characterized by SEM/EDX, FTIR, XRD, UV, and BET analyses and then further used as an adsorbent to remove Cr(VI) ions from simulated wastewater. Optimal pH, temperature and adsorbent dosage were determined through batch mode studies. High removal efficiency and adsorption capacity were observed at pH 4, 0.25 g L -1 dosage, and 25 mg L -1 concentration of Cr(VI). Experimental data were modelled with different adsorption kinetics (Elovich model, PFO, PSO, IDP model) and isotherms (Langmuir, Freundlich, and Temkin), and it was found the adsorption process was well fitted to Langmuir with an R 2 value greater than>0.99. Computational calculation showed that the g-ZnO nanoparticles became ∼14 times more dynamic with delocalized surface states making them a relevant platform to adsorb Cr with greater work function compatibility supporting the experimental findings. The Q max adsorption capacity of g-ZnO was 315.46 mg g -1 from Langmuir calculations. Thermodynamic calculations reveal that the Cr (VI) adsorption process was spontaneous and endothermic, with a positive ΔS value representing the disorder at the solid-solution interface during the adsorption. In addition, the present study has demonstrated that these g-ZnO nanoparticles show strong antibacterial activities against P. aeruginosa (MTCC 1688) and E. coli (MTCC 1687). Also, the novel g-ZnO adsorbent capacity to remove Cr(VI) from simulated water revealed that it could be reused at least six times with higher removal rates during regeneration experiments. The results obtained from adsorption and antimicrobial activities suggest that g-ZnO nanoparticles could be used effectively in real-time wastewater and agricultural safety applications., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Simranjeet singh reports financial support was provided by Indian Institute of Science., (Copyright © 2023 Elsevier Ltd. All rights reserved.)

Heavy metals represent a considerable threat, and the current study deals with synthesizing a novel MOF nanocomposite by intercalating graphene oxide (GO) and linker UiO-66-NDC. It was shown that UiO-66-NDC/GO had enhanced the removal efficiency of Pb (II) ions at pH 6. The adsorption kinetics data followed the PSO (Type 2) representing chemisorption. Adsorption data were also fitted with three different isotherms, namely Temkin, Freundlich, & Langmuir, and the Temkin model exhibited the best correlation (R 2 0.99), representing the chemisorption nature of the adsorption process. The maximum adsorption capacity (qmax) of Pb (II) ions using Langmuir was found to be 254.45 mg/g (298 K). The Pb (II) adsorption process was confirmed to be exothermic and spontaneous as the thermodynamic parameters H° and G° were determined to have negative values. MOF nanocomposite also represents significant reusability for up to four regeneration cycles using 0.01 M HCl; for the next four, it works quite efficiently after regeneration. Meanwhile, the simulation findings confirm the superior dynamic stability (∼08 times) of the MOF nanocomposite as compared to the GO system. The removal of Pb (II) from simulated wastewater samples using a super nano-adsorbent using a MOF nanocomposite is described here for the first time., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 Elsevier Inc. All rights reserved.)

Chromium is detected in most ecosystems due to the increased anthropogenic activities in addition to that developed from natural pollution. Chromium contamination in the food chain results due to its persistent and non-degradable nature. The release of chromium in the ecosystem accretes and thereafter impacts different life forms, including humans, aquatic and terrestrial organisms. Leaching of chromium into the ground and surface water triggers several health ailments, such as dermatitis, eczematous skin, allergic reactions, mucous and skin membrane ulcerations, allergic asthmatic reactions, bronchial carcinoma and gastroenteritis. Physiological and biological treatments for the removal of chromium have been discussed in depth in the present communication. Adsorption and biological treatment methods are proven to be alternatives to chemical removal techniques in terms of cost-effectiveness and low sludge formation. Chromium sensing is an alternative approach for regular monitoring of chromium in different water bodies. This review intended to explore different classes of sensors for chromium monitoring. However, the spectrochemical methods are more sensitive in chromium ions sensing than electrochemical methods. Future study should focus on miniaturization for portability and on-site measurements without requiring a large instrument provides a good aspect for future research., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 Elsevier Ltd. All rights reserved.)

A novel green nanocomposite has been prepared by immobilizing CaO nanoparticles (CaO NPs) on the surface of graphene oxide. Biogenic CaO-NPs were synthesized from Lala clamshells. Morphological and structural characterizations of the nanocomposite were studied extensively. The adsorption capacity (q max ) of the nanocomposite for removing Cr(VI) was 38.04 mg g -1 . In addition to this, the adsorption data were adequately simulated with Langmuir, Freundlich, Temkin, and pseudo-second-order models, suggesting that the adsorption process was the combination of external mass transfer and chemisorption. Electrostatic interaction was the dominant mechanism for Cr(VI) removal. In addition, the synthesized nanocomposites also serve as an excellent sensor for Cr(VI) sensing, with a limit of detection (LOD) of 0.02 μM utilizing electrochemical methods. Therefore, this green nanocomposite can simultaneously serve as an adsorbent and sensor for Cr(VI)removal from aqueous solutions., (Copyright © 2022 Elsevier Ltd. All rights reserved.)

Environmental pollution caused by the discharge of raw and partly treated distillery effluent has become a serious and threatening problem due to its high pollution load. The aim of the present study was to assess the physicochemical load in alcohol distillery effluent before and after biomethanation treatment and the cyto- and genotoxicity effects of refractory pollutants emanated in raw/untreated and biomethanated distillery effluent on the ultrastructural and biochemical responses of Allium cepa root tip cells. Physicochemical analysis revealed high biochemical oxygen demand (BOD: 47840-36651 mg L -1 ), chemical oxygen demand (COD: 93452-84500 mg L -1 ) and total dissolved solids (TDS: 64251-74652 mg L -1 ) in raw and biomethanated effluent along with metal(loid)s (Fe: 456.152-346.26; Zn: 1.654-1.465; Cu: 0.648-0.562; Ni: 1.012-0.951, and Pb: 0.264 mg L -1 ) which were beyond the safe discharge values prescribed by the environmental regulatory agencies. The UV-Visible and Fourier transform infrared spectrophotometry analyses confirmed the high levels of organic, inorganic, and mixed contaminants discharged in raw and biomethanated distillery effluents. Furthermore, GC-MS analysis characterised chemical contaminants, such as hexadecanoic acid, butanedioic acid, bis(trimethylsilyl) ester; hexadecane, 2,6,11,15-tetramethyl, stigmasterol, and β-sitosterol trimethylsilyl ether that have been reported as androgenic-mutagenic, and endocrine disrupting chemicals by the United States Environmental Protection Agency (U.S. EPA). The cytotoxicity measured by A. cepa showed dose depended inhibition root growth inhibition and simultaneous reduction in mitotic index in tested effluents. The chromosomal aberrations studies resulted in laggard chromosomes, sticky chromosomes, vagrant chromosomes, chromosome loss, c-mitosis, chromosome bridge, abnormal metaphase, and disturbed anaphase as found in a dose-dependent manner. Furthermore, dose-dependent enhancement in the levels of malondialdehyde, hydrogen peroxide, and antioxidative enzymes, such as superoxide dismutase, ascorbate peroxidase, and catalase were found to be higher in raw effluents treated root cells compared to biomethanated distillery effluent. Analysis of ultrastructural changes in root tip cells by TEM analysis revealed dramatic changes in the morphology of cell organelles and accumulation of metallic elements in and on the surface tissues. The results concluded that the discharged distillery effluents retained certain toxic pollutants which imposed cytotoxic and genotoxic hazards to A. cepa. Thus, for the sake of environmental protection, the raw as well as the disposed biomethanated effluent must be efficiently treated before its dumping into the terrestrial ecosystem., (Copyright © 2022 Elsevier Ltd. All rights reserved.)

With millions of tonnes of plastic pollution generated every year, small-sized plastic particles, including micro- and nanoplastics, end up in freshwater systems. Due to the very small size and very large specific surface area of nanoplastics, they are known to be persistent and toxic in our environment. These particles are also known to react with other water-borne contaminants and cause acute toxicity in organisms. Nanoplastics are prone to biomagnification and can be transported to humans through various pathways. This study aims to contribute towards understanding the behaviour of nanoplastics in our environment, specifically through identification of various sources, detection techniques, toxicity estimation, health risk in humans, environmental fate, recovery and reuse, and future challenges and limitations. Detailed review on the toxic effects of nanoplastics on various organisms and their degradation rates in soil and water matrices are provided. The suitability of small- and large-scale separation techniques for the removal of nanoplastics in wastewater treatment plants is also discussed. Current challenges and future perspectives in understanding the fate and transport of nanoplastics in the environment are also discussed. Research gaps, including the development of quantification techniques, estimation of degradation mechanisms, transport in marine ecosystems, and development of sensors to examine nanoplastics in the environment, are explored. Finally, we can limit the release of nanoplastics to the environment through reduction, reuse and recycling (3 Rs) of bulk plastic products., (Copyright © 2021 Elsevier Ltd. All rights reserved.)

Herein, for the adsorption and detection of As (III), multifunctional nanohybrid have been synthesized using a solvothermal approach. Structural and functional characterizations confirmed the impregnation of the ZnO over graphene oxide. Nanohybrid exhibits a remarkable q max (maximum adsorption capacity) of 8.17 mg/g, at an adsorbent dose of 3 g/L and pH of 8.23. Higher adsorption with nanohybrid was attributed to a large BET surface area of 32.950 m 2 /g. The chemical nature and adsorption behaviour of As(III) on ZnO-GO were studied by fitting the data with various adsorption isotherms (Langmuir & Freundlich) and kinetics models (six models). It is observed from the findings that removal of As(III) with ZnO-GO nanocomposite appears to be technically feasible with high removal efficiency. The feasibility of the nanocomposite to function as a sensor for the detection of As(III) was also evaluated. The fabricated sensor could detect As(III) with a lower limit of detection of 0.24 μM and linear range up to 80 μM. Overall, this study is significant in nanohybrid as a multifunctional composite for the adsorption and detection of As (III) from wastewater., (Copyright © 2021 Elsevier Ltd. All rights reserved.)

Metal-based adsorbents are limited for hexavalent chromium [Cr(VI)] adsorption from aqueous solutions because of their low adsorption capacities and slow adsorption kinetics. In the present study, decorated zinc oxide (ZnO) nanoparticles (NPs) on graphene oxide (GO) nanoparticles were synthesized via the solvothermal process. The deposition of ZnO NPs on graphene oxide for the nanohybrid (ZnO-GO) improves Cr(VI) mobility in the nanocomposite or nanohybrid, thereby improving the Cr(VI) adsorption kinetics and removal capacity. Surface deposition of ZnO on graphene oxide was characterized through Fourie Transform Infra-red (FTIR), UV-Visible, X-ray Diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM), Energy Dispersive Spectroscopy (EDS), and Brunauer-Emmett-Teller (BET) techniques. These characterizations suggest the formation of ZnO-GO nanocomposite with a specific area of 32.95 m 2 /g and pore volume of 0.058 cm 2 /g. Batch adsorption analysis was carried to evaluate the influence of operational parameters, equilibrium isotherm, adsorption kinetics and thermodynamics. The removal efficiency of Cr(VI) increases with increasing time and adsorbent dosage. FTIR, FESEM and BET analysis before and after the adsorption studies suggest the obvious changes in the surface functionalization and morphology of the ZnO-GO nanocomposites. The removal efficiency increases from high-acidic to neutral pH and continues to decrease under alkaline conditions as well. Mathematical modeling validates that the adsorption follows Langmuir isotherm and fits well with the pseudo 2nd order kinetics (Type 5) model, indicating a homogeneous adsorption process. The thermodynamics study reveals that Cr(VI) adsorption on ZnO-GO is spontaneous, endothermic, and entropy-driven. A negative value of Gibb's Free Energy represents the thermodynamic spontaneity and feasibility of the sorption process. To the best of our knowledge, this is the first study of Cr(VI) removal from aqueous solution using this hybrid nanocomposite at near-neutral pH. The synthesized nanocomposites prove to be excellent candidates for Cr(VI) removal from water bodies and natural wastewater systems., (Copyright © 2021 Elsevier Inc. All rights reserved.)

Nitrate pollution is eminent in almost all the developing nations as a result of increased natural activities apart from anthropogenic pollution. The release of nitrates in more than critical quantities into the water bodies causes accretion impacts on living creatures, environmental receptors, and human vigour by accumulation through the food chain. Nitrates have recently acquired researchers' huge attention and extend their roots in environmental contamination of surface and groundwater systems. The presence of nitrate in high concentrations in surface and groundwater triggers several health problems, for instance, methemoglobinemia, diabetes, eruption of infectious disorders, harmfully influence aquatic organisms. Sensing nitrate is an alternate option for monitoring the distribution of nitrate in different water bodies. Here we review electrochemical, spectroscopic, and electrical modes of nitrate sensing. It is concluded that, among the various sensors discussed in this review, FET sensors are the most desirable choice. Their sensitivity, ease of use and scope for miniaturisation are exceptional. Advanced functional materials need to be designed to satiate the growing need for environmental monitoring. Different sources of nitrate contamination in ground and surface water can be estimated using different techniques such as nitrate isotopic composition, co contaminants, water tracers, and other specialized techniques. This review intends to explore the research work on remediation of nitrate from wastewater and soil using different processes such as reverse osmosis, chemical denitrification, biological denitrification, ion exchange, electrodialysis, and adsorption. Denitrification proves as a promising alternative over previously reported techniques in terms of their nitrate removal because of its high cost-effectiveness., (Copyright © 2021 Elsevier Ltd. All rights reserved.)

Antibiotics overuse, inappropriate conduct, and discharge have led to adverse effects on various ecosystems. The occurrence of antibiotics in surface and drinking water is a matter of global concern. It is responsible for multiple disorders, including disruption of endocrine hormones and high chronic toxicity. The hospitals, pharmaceutical industries, households, cattle farms, and aquaculture are the primary discharging sources of antibiotics into the environment. This review provides complete detail on applying different nanomaterials or nanoparticles for the efficient removal of antibiotics from the diverse ecosystem with a broader perspective. Efforts have been made to focus on the degradation pathways and mechanism of antibiotic degradation using nanomaterials. More light has been shed on applying nanostructures in photocatalysis, which would be an economical and efficient solution. The nanoscale material or nanoparticles have incredible potential for mineralizing pharmaceutical compounds in aqueous solutions at low cost, easy handling characteristics, and high efficacy. Furthermore, nanoparticles can absorb the pharmaceutical by-products and wastes at a minimum cost as they can be easily recycled. With the increasing number of research in this direction, the valorization of pharmaceutical wastes and by-products will continue to expand as we progress from old conventional approaches towards nanotechnology. The utilization of nanomaterials in pharmaceutical wastewater remediation is discussed with a major focus on valorization, energy generation, and minimization and its role in the circular economy creating sustainable development., (Copyright © 2021 Elsevier Ltd. All rights reserved.)

Wastewater flowing in streams and nallahs across India carries several trace metals, including metalloid arsenic (As), which are considered serious environmental contaminants due to their toxicity, and recalcitrant nature. In this study, we determined the phytoremediation of As by Eichhornia crassipes (Mart.) Solms either alone or in association with plant growth-promoting rhizobacteria. Pseudomonas and Azotobacter inoculation to E. crassipes resulted in enhanced As removal compared to uninoculated control. Co-inoculation with a consortium of Pseudomonas, Azotobacter, Azospirillum, Actinomyces, and Bacillus resulted in a higher As (p < 0.05) phytoaccumulation efficiency. P. aeruginosa strain jogii was found particularly effective in augmenting As removal by E. crassipes. Our findings indicate that the synergistic association of E. crassipes and various rhizobacteria is an effective strategy to enhance removal of As and thus may be utilized as an efficient biological alternative for the removal of this metalloid from wastewaters.