Search

Raphidophytes are flagellate unicellular algae that causes algal blooms in drinking water sources. In Japan, it was recently reported that the concentration of trichloroacetic acid (TCAA), a major chlorinated disinfection byproduct (DBP), increased dramatically in drinking water when the source water contained raphidophytes. Additionally, raphidophytes produced haloacetic acid (HAA) precursors, especially TCAA precursors, in high concentrations. However, their properties are still unknown, and thus, well-designed countermeasures against DBP formation have not yet been established. Therefore, in this study, the HAA precursors originated from raphidophytes in natural water collected from the algal blooms in Muro Dam (Nara Prefecture, Japan) and Gonyostomum semen (G. semen), a raphidophyte species, cultivated in the laboratory, were characterized to provide the information for establishing suitable treatment strategies. Using several high-performance liquid chromatography columns, solid-phase extraction cartridges, and ultrafiltration devices, and the spectral profiles, we discovered that the HAA precursors are highly hydrophilic and high-molecular-weight compounds with acidic and phenolic functional groups. Further characterization of the high-molecular-weight fraction (> 3 kDa) from the G. semen culture showed that the HAA precursors had a molecular weight of ~10-60 kDa, and that they were not protein molecules despite containing a large amount of nitrogen atoms. Furthermore, the TCAAFP of the fraction (310 ± 25 μg/mg C) were as high as phenol, known as a reactive TCAA model precursor. The presence of unique and unreported DBP precursors was confirmed., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier B.V. All rights reserved.)

Water toxicity detection, as a valuable supplement to conventional water quality measurement, is an important method for evaluating water environmental quality standards. However, the toxicity of composite pollutants is more complicated due to their mixture effects. This study developed a novel, rapid and interference-resistant detection method for water toxicity based on an electrochemical biosensor using peak current from nitrite oxidation as a signal. Toxicants could weaken the characteristic peak current of nitrite to indicate the magnitude of toxicity. The proof-of-concept study was first conducted using a synthetic water sample containing trichloroacetic acid (TCAA), and then the results were compared with those of the traditional toxicity colorimetric method (CCK-8 kit) and laser confocal microscopy (CLSM). The accuracy of the biosensor was further verified with water samples containing individual pollutants such as Cd 2+ (50-150 μg/L), Cr 6+ (20-80 μg/L) mixture, triclosan (TCS; 0.1-1.0 μg/L) and TCAA (10-80 μg/L), or a mixture of the above. The viability of the sensor was further validated with the actual water sample from the Tuojiang River. The results demonstrated that although the concentration of a single conventional pollutant in water did not exceed the discharge standard for surface water, the comprehensive toxicity of natural water should not be ignored. This method could be a beneficial supplement to conventional water quality detection to understand the characteristics of the water, and thus contribute to the next stage of water treatment., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Ltd. All rights reserved.)

People are exposed to chlorinated by-products (CBPs) through the consumption of cold tap water (CTW) (ingestion, inhalation, dermal contact) but also through the use of hot tap water (HTW) in such activities as showering and bathing (inhalation, dermal contact). This study focuses on the impact of residential water heating on CBP levels in tap water. Trihalomethane (THM) and haloacetic acid (HAA) levels were measured in the CTW and HTW of 50 residences located in two distribution systems supplied by chlorinated surface water during summer and winter. Results show important differences between CBP levels measured in cold and hot tap water. However, the magnitude of changes differs according to the specific species of THMs and HAAs, the season, the distribution system and the location within the same distribution system. Residential water heating led to an increase in average THM levels for the two distribution systems studied, which tended to be greater in winter. Residential water heating affected the two main HAA species found in the area studied (dichloroacetic (DCAA) and trichloroacetic (TCAA) acids) differently. In fact, the average DCAA levels increased due to water residential heating while a small change in average levels was observed for TCAA. However, the water heating impact on HAAs (in terms of importance and sometimes of tendency (increase vs. decrease)) may also differed between residences. The influence of seasons on the change in the average DCAA and TCAA levels (in μg/L) from residential water heating was not statistically significant except for TCAA levels in one distribution system. Results show the importance of considering site-specific characteristics of CTW (CBP level, temperature, residual chlorine, etc.) to estimate the levels of CBPs in HTW in CBP exposure assessment studies (and not to generalize for an entire population). The reported data can thus be useful in assessing for exposure to DBPs in epidemiological studies., (Copyright © 2018 Elsevier B.V. All rights reserved.)

We are reporting a novel biosensing platform based on a hybrid nanomaterial that combines the advantages of Nafion-coated multiwalled carbon nanotubes (MWCNTs) and mesoporous silica MCM41 nanoparticles functionalized with hemoglobin (Hb). MWCNTs-MCM41-Hb hybrid bioconjugate was characterized by scanning electron microscopy (SEM), UV-vis spectroscopy and electrochemical techniques after deposition at glassy carbon electrodes (GCE). The combination of the high surface area, biocompatibility and protein loading capacity of MCM41 nanoparticles and the high surface area and catalytic properties of MWCNTs allowed the direct electron transfer (DET) between Hb and the electrode surface. The electron transfer rate constant (k) and the surface coverage of electroactive Hb (Γ Hb ) were 5.2 s -1 and 4.7 × 10 -10 mol cm -2 , respectively. The GCE modified with the nanostructured architecture (GCE/MWCNTs-MCM41-Hb) was successfully used as a third-generation biosensor for the highly sensitive and selective quantification of nitrite (NO 2 - ) and trichloroacetic acid (TCA) by taking advantage of the excellent biocatalytic activity of Hb and the efficient direct charge transfer of the heme group., (Copyright © 2018 Elsevier B.V. All rights reserved.)

Water disinfection plays a crucial role in water safety but it is also a matter of concern as the use of disinfectants promotes the formation of disinfection by-products (DBPs). Haloacetic acids (HAAs) are one of the major classes of DBPs since they are frequently found in treated water, are ubiquitous, pervasive and have high water solubility, so a great concern emerged about their formation, occurrence and toxicity. Exposure to HAAs is influenced by consumption patterns and diet of individuals thus their bioavailability is an important parameter to the overall toxicity. In the current study the bioacessibility of the most representative HAAs (chloroacetic acid - MCAA, bromoacetic acid - MBAA, dichloroacetic acid - DCAA, dibromoacetic acid - DBAA, and trichloroacetic acid - TCAA) after simulated in vitro digestion (SIVD) in tap water and transport across Caco-2 monolayers was evaluated. Compounds were monitored in 8 points throughout the digestion phases by an optimized LC-MS/MS methodology. MCAA and MBAA were not bioaccessible after SIVD whereas DCAA, DBAA and TCAA are highly bioaccessible (85 ± 4%, 97 ± 4% and 106 ± 7% respectively). Concerning transport assays, DCAA and DBAA were highly permeable throughout the Caco-2 monolayer (apparent permeability and calculated fraction absorbed of 13.62 × 10(-6) cm/s and 90% for DCAA; and 8.82 × 10(-6) cm/s and 84% for DBAA), whereas TCAA showed no relevant permeability. The present results may contribute to efficient risk analysis studies concerning HAAs oral exposure from tap water taking into account the different biological behaviour of these chemically similar substances., (Copyright © 2016 Elsevier Ltd. All rights reserved.)

Dissolved organic matter (DOM) represents the major pool of organic precursors for harmful disinfection byproducts, such as haloacetic acids (HAAs), formed during drinking water chlorination, but much of it remains molecularly uncharacterized. Knowledge of model precursors is thus a prerequisite for understanding the more complex whole water DOM. The utility of HAA formation potential data from model DOM precursors, however, is limited due to the lack of comparability to water samples. In this study, the formation kinetics of dichloroacetic acid (DCAA) and trichloroacetic acid (TCAA), the two predominant HAA species, were delineated upon chlorination of seventeen model DOM precursors and sixty-eight inland lake water samples collected from the Upper Midwest region of the United States. Of particular interest was the finding that the DCAA and TCAA formation rate constants could be grouped into four statistically distinct clusters reflecting the core structural features of model DOM precursors (i.e., non-β-diketone aliphatics, β-diketone aliphatics, non-β-diketone phenolics, and β-diketone phenolics). A comparative approach built upon hierarchical cluster analysis was developed to gain further insight into the chlorine reactivity patterns of HAA precursors in inland lake waters as defined by the relative proximity to four model precursor clusters. This work highlights the potential for implementing an integrated kinetic-clustering approach to constrain the chlorine reactivity of DOM in source waters.

Chlorine has been utilized in the early stages of water treatment processes as disinfectant. Disinfection for drinking water reduces the risk of pathogenic infection but may pose a chemical threat to human health due to disinfection residues and their by-products (DBP) when the organic and inorganic precursors are present in water. In the last two decades, many modeling attempts have been made to predict the occurrence of DBP in drinking water. Models have been developed based on data generated in laboratory-scale and field-scale investigations. The objective of this paper is to develop a predictive model for DBP formation in the Alexandria governorate located at the northern west of Egypt based on field-scale investigations as well as laboratory-controlled experimentations. The present study showed that the correlation coefficient between trihalomethanes (THM) predicted and THM measured was R (2)=0.88 and the minimum deviation percentage between THM predicted and THM measured was 0.8 %, the maximum deviation percentage was 89.3 %, and the average deviation was 17.8 %, while the correlation coefficient between dichloroacetic acid (DCAA) predicted and DCAA measured was R (2)=0.98 and the minimum deviation percentage between DCAA predicted and DCAA measured was 1.3 %, the maximum deviation percentage was 47.2 %, and the average deviation was 16.6 %. In addition, the correlation coefficient between trichloroacetic acid (TCAA) predicted and TCAA measured was R (2)=0.98 and the minimum deviation percentage between TCAA predicted and TCAA measured was 4.9 %, the maximum deviation percentage was 43.0 %, and the average deviation was 16.0 %.

Disinfection byproducts were measured in the finished drinking water from ten water treatment plants in three Chinese cities - Guangzhou, Foshan and Zhuhai. A total of 155 water samples were collected in 2011 and 2012. The median (range) of trihalomethane (THM) and haloacetic acid (HAA) levels were 17.7 (0.7-62.7) μg/L and 8.6 (0.3-81.3) μg/L, respectively. Chloroform, dichloroacetic acid and trichloroacetic acid were the dominant species observed in Guangzhou and Foshan water, while brominated THMs predominated in water from Zhuhai. Haloacetonitriles, haloketones, chloral hydrate and trichloronitromethane were usually detected at levels ranging from unquantifiable (<0.2μg/L) to 12.2μg/L (choral hydrate). THMs and HAAs showed clear seasonal variations with the total concentrations higher in winter than in summer. Correlations among DBP levels varied, with the strongest linear correlation observed between chloroform and chloral hydrate levels (R(2)=0.77). The risk of cancer from ingestion, inhalation and dermal contact exposure to THMs was estimated. CHCl2Br contributed the highest percentage of the cancer risk from ingestion pathway and CHCl3 contributed the highest of cancer risk from inhalation pathway., (Copyright © 2013 Elsevier B.V. All rights reserved.)

An innovative haloacetic acid (HAA) removal process was developed. The process consisted of a zero-valent iron (Fe(0)) column followed by a biologically active carbon (BAC) column that were efficient in degrading tri- and di-HAAs, and mono- and di-HAAs, respectively. The merit of the process was demonstrated by its performance in removing trichloroacetic acid (TCAA). An empty bed contact time of 10 min achieved nearly complete removal of 1.2 μM TCAA and its subsequent products, dichloroacetic acid (DCAA) and monochloroacetic acid (MCAA). HAA removal was a result of chemical dehalogenation and biodegradation rather than physical adsorption. Preliminary kinetic analyses were conducted and the pseudo-first-order rate constants were estimated at ambient conditions for Fe(0) reduction of TCAA and biodegradation of DCAA and MCAA by BAC. This innovative process is highly promising in removing HAAs from drinking water, swimming pool water, and domestic or industrial wastewater., (Copyright © 2012 Elsevier Ltd. All rights reserved.)

A solid phase microextraction method was used for the analysis of nine haloacetic acids (HAAs) in water and air (aerosols) from indoor swimming pools (ISPs). The analysis is characterized by derivatization of HAAs to their methyl-esters with dimethyl sulphate, headspace solid phase microextraction (HS-SPME) with a Carboxen-polydimethylsiloxane (CAR-PDMS) fiber and gas chromatography - electron capture detector (GC/ECD). High correlation coefficients were obtained for esters mixture calibration lines and detection limits were found to be at the low ppb level. Repeatability was assessed and coefficients of variation varied from 10 to 20%. Reproducibility was also evaluated and coefficients of variation from 15 to 25% were obtained. Analytical results from four Portuguese ISPs showed that the mean concentration of total HAAs (THAAs) in water ranged from 10 ± 2 to 183 ± 28 μg/L in which 55 ± 20% corresponded to trichloroacetic and dichloroacetic acids (TCAA and DCAA). THAAs highest concentrations were directly related to higher ISPs' water organic matter content. In the lack of European specific regulation for water from ISPs and taking into consideration that ingestion is a form of exposure, THAAs concentration values were compared with drinking water maximum contamination level (MCL) of 60 μg/L proposed by the US EPA for the sum of five HAAs. In 35% of water sampling campaigns the sum of MBAA (monobromoacetic acid), MCAA (monochloroacetic acid), DCAA and TCAA exceeded that MCL value. The concentrations obtained for THAAs in the ISPs' atmosphere ranged from 5 ± 1 to 64 ± 10 μg/m(3) (T = 28°C at 5 cm above the water surface) and were proportional to the aerosols' quantity, which was deeply related to indoor air ventilation system.

Adsorption performance of 5 GACs were compared on two abundant haloacetic acids (HAAs) as disinfection by-products (dichloroacetic acid and trichloroacetic acid). The adsorption behaviours of the two HAAs were well correlated with Langmuir equation. When the two HAAs co-existed, trichloroacetic acid tended to be adsorbed more easily. The adsorption capacity of a foreign GAC-A for dichloroacetic acid was 4.4-5.7 times that of domestic GACs, and 3.8 times that of another foreign GAC-B, while the adsorption capacity of a foreign GAC-A for trichloroacetic acid was 4.0-5.4 times that of domestic GACs, and 2.6 times that of another foreign GAC-B. The equilibrium study of competitive adsorption between dichloroacetic acid and trichloroacetic acid on GAC-A demonstrates that the relative adsorption capacity of HAAs has a linear increase with their relative equilibrium concentration. The adsorption capacity for trichloroacetic acid is sensitive to changes at its equilibrium concentration greater than that for dichloroacetic acid.

A simple and rapid headspace method for gas chromatographic determination of dichloroacetic acid (DCAA) and trichloroacetic acid (TCAA) in drinking water was developed. Acidic methanol esterification followed by a headspace technique using a capillary column gas chromatograph (GC) equipped with an electron capture detector (ECD) was applied to determine the levels of DCAA and TCAA in drinking water. The major advantages of this method are the use of acidic methanol as the derivatization agent instead of the hazardous diazomethane, and esterification is carried out in water instead of organic solvent. DCAA and TCAA methyl esters produced in the reaction were determined directly by a headspace GC/ECD method. The linear correlation coefficients at concentrations ranging from 0 to 60 microg/L were 0.992 and 0.996 for DCAA and TCAA, respectively. The relative standard deviations (RSD, %) for the determination of DCAA and TCAA in drinking water were 15 and 21.3%, respectively (n=3). The detection limits of this method were 3 and 0.5 microg/L for DCAA and TCAA, respectively, and the recovery was 68-103.2% for DCAA and TCAA.

The concentrations and input/output fluxes of trichloroacetic acid (TCA) were measured in all relevant media for one year at a 0.86 km2 upland conifer plantation and moorland catchment in SW Scotland (n > 380 separate samples analyzed). Annual wet precipitation to the catchment was 2.5 and 0.4 m for rain and cloud, respectively. TCA input to the catchment for the year was 2100 g, predominantly in rainwater (86%), with additional input via cloudwater (13%) and gas plus particle dry deposition (1%). There were no seasonal trends in TCA deposition, and cloudwater concentration was not enhanced over rainwater. TCA in precipitation exceeded concentrations estimated using currently accepted routes of gas-phase oxidation from anthropogenic chlorinated hydrocarbon precursors, in agreement with previous studies. Export of TCA from the catchment in streamwater totalled 1970 g for the year of study. The TCA concentration in streamwater at outflow (median 1.2 microg L(-1)) was significantly greater than that before the stream had passed through the conifer plantation. To well-within measurement uncertainties, the catchment is currently at steady-state with respect to TCA input/output. The catchment reservoir of TCA was dominated by soils (approximately 90%), with the remainder distributed in forest litter (approximately 9%), forest branchwood and stemwood (approximately 0.7%), forest foliage (approximately 0.5%), and moorland foliage (approximately 0.1%). Although TCA is clearly taken up into foliage, which consequently may be important for the vegetation, this was a relatively minor process for TCA at the catchment scale. If it is assumed, on the basis of laboratory extraction experiments, that only approximately 20% of "whole soil" TCA measured in this work was water extractable, then total mass of TCA in the catchment is reduced from approximately 13 to approximately 3.5 kg. Comparing the latter value with the annual flux yields an average steady-state residence time for TCA in the catchment of approximately 1-2 y, if all TCA is involved in catchment turnover. Considering that other evidence indicates the lifetime of TCA in soil and biota is considerably shorter than this (weeks rather than years), the magnitude of the TCA reservoir is suggested to be strong evidence for net natural TCA production in soils and/or that the majority of TCA in the reservoir is not involved with external fluxes.

A simple, closed-form analytical expression based on the homogenous solution diffusion model is derived for contaminant removal during nanofiltration (NF) of ground and surface water. Solute permeation and back-diffusion coefficients were used as fitting parameters to model rejection characteristics of four thin-film composite NF membranes under conditions typical of drinking water NF. Nonlinear fits of the model to experimental data suggests that the United States Environmental Protection Agency's (USEPA)'s Information Collection Rule protocol for bench-scale studies could be improved to obtain greater precision of the mass transfer coefficients. The model was found to fit rejection data for several water treatment contaminants including total organic carbon, precursors to total organic halide, four trihalomethanes and nine haloacetic acids containing chlorine and bromine, calcium and total hardness, alkalinity and conductivity. The simplified approach to mass transfer calculations from multisolute systems suggests that feed water recovery has a stronger influence on contaminant rejection than permeate flux. Evidence for coupled transport of divalent inorganic ions is also presented. Even though the model developed does not account for ion coupling and cannot be applied in a purely predictive mode, it can assist in the better design and interpretation of data obtained from site-specific pilot-scale water treatment NF studies conducted in support of plant design.

This study compares four different commercial sorbents, LC-SAX (a quaternary ammonium anion exchanger), LiChrolut EN (a highly crosslinked styrene-divinylbenzene), Envi-Carb (a graphitized carbon black) and Oasis HLB [a macroporous poly(divinylbenzene-co-N-vinylpyrrolidone) copolymer], for the solid-phase extraction (SPE) of various haloacetic compounds from aqueous samples. The recoveries with the different sorbents were studied by coupling an off-line SPE system to capillary electrophoresis with indirect photometric detection. The recoveries were highest when LiChrolut EN was used. The limits of detection for the compounds are in the low microgram per litre range and the recovery values are over 80% for dichloroacetic acid and trichloroacetic acid, two of the most habitual haloacetic acids in chlorinated water, when 500 ml of standard solution was preconcentrated using this sorbent. Finally, the performance of the method with different water samples, the effect of chlorination in a treatment plant and the evolution of the haloacetic acids in the water distribution system were tested and the results were compared with those obtained using liquid-liquid extraction and gas chromatography-mass spectrometry.