Search

This paper studies the postfault control of a nine-phase six-terminal induction machine (IM) during single open-line fault, which was recently proposed for high-power medium-voltage applications as a promising alternative to conventional six-phase IMs. The required optimal reference currents to provide prefault loading conditions under one-line open are derived using the two most common optimization criteria employed in multiphase drives, namely, maximum torque and minimum loss modes. A postfault controller, based on conventional decoupling Clarke's transformation, is then used to ensure the same controller structure under all conditions. Consequently, the machine characteristic curves, achievable torque, and stator copper losses under these different modes are compared. A comparison with a conventional asymmetrical six-phase winding is also given. A 1.5-Hp prototype IM is used for experimental verification. [ABSTRACT FROM PUBLISHER]

In multiphase machine drives, accuracy of the estimated machine parameters is crucial for effective performance prediction and/or control. While a great amount of work has been done on parameter estimation for three-phase machines, corresponding discussions for six-phase machine remain scarce. It has been proven in the literature that the effect of mutual leakage inductance between different winding layers has a significant impact on the equivalent machine reactance, which challenges the standard separation method of stator and rotor leakage inductances from the measured locked-rotor impedance. In this paper, parameter identification of an asymmetrical six-phase induction machine using six-phase no-load and locked-rotor tests is discussed. A zero-sequence test using an improved equivalent circuit is proposed to improve the accuracy of the estimated parameters. The concept is verified using experimental results obtained from a low-power prototype asymmetrical six-phase machine. [ABSTRACT FROM AUTHOR]

The interior permanent magnet (IPM) machine equipped with a fractional-slot concentrated winding (FSCW) has met an increasing interest in electric vehicle applications due to its higher power density and efficiency. Torque production is due to both PM and reluctance torques. However, one of the main challenges of FSCWs is their inability to produce a high-quality magnetomotive force (MMF) distribution, yielding undesirable rotor core and magnet eddy-current losses. Literature shows that the reduction of low-order space harmonics significantly reduces these loss components. Moreover, it has been previously shown that by employing a higher number of layers, although causing some reduction in the winding factor of the torque-producing MMF component, both machine saliency and reluctance torque components are improved. Recently, a dual three-phase winding connected in a star/delta connection has also shown promise to concurrently enhance machine torque of a surface-mounted PM machine while significantly reducing both rotor core and magnet losses. In this paper, a multilayer winding configuration and a dual three-phase winding connection are combined and applied to the well-known 12-slot/10-pole IPM machine with v-shaped magnets. The proposed winding layout is compared with a conventional double-layer winding, a dual three-phase double-layer winding, and a four-layer winding. The comparison is carried out using 2-D finite-element analysis. The comparison shows that the proposed winding layout, while providing similar output torque to a conventional double-layer three-phase winding, offers a significant reduction in core and magnet losses, correspondingly a higher efficiency, improves the machine saliency ratio, and maximizes the reluctance toque component. [ABSTRACT FROM AUTHOR]

One of the main drawbacks of nonoverlapped coils in fractional slot concentrated winding permanent magnet (PM) machines are the high eddy current losses in both rotor core and permanent magnets induced by the asynchronous harmonics of the armature reaction field. It has been shown in the literature that the reduction of low space harmonics can effectively reduce the rotor eddy current losses. This paper shows that employing a combined star-delta winding to a three-phase PM machine with fractional slot windings and with a number of slots equal to 12, or its multiples, yields a complete cancellation to the fundamental magneto-motive force (MMF) component, which significantly reduces the induced rotor eddy current. Besides, it offers a slight increase in machine torque density. A case study on the well-known 12-slot/10-pole PM machine is conducted to explore the proposed approach. With the same concept, the general $n$ -phase PM machine occupying $4n$ slots and with a dual $n$ -phase winding is then proposed. This configuration offers a complete cancelation of all harmonics below the torque producing MMF component. Hence, the induced eddy currents in both rotor core and magnets are significantly reduced. The winding connection and the required number of turns for both winding groups are also given. The concept is applied to a 20-slot/18-pole stator with a dual five-phase winding, where the stator winding is connected as a combined star/pentagon connection. The proposed concept is assessed through a simulation study based on 2-D finite element analysis. [ABSTRACT FROM AUTHOR]

This paper investigates a nontriplen multiphase induction machine when fed with harmonic current injection with different sequences for an open loop optimized flux distribution that produce a quasi-square wave in the machine air gap. This maximizes iron utilization, giving more torque per ampere. The relation between the fundamental and other harmonic components can be determined for the best iron utilization using genetic algorithms where optimum flux distribution with different injected harmonic order can be obtained. This means, the target is to optimize the flux distribution during no-load to determine the optimum constants that guarantee approximate square wave air-gap flux. The paper focuses on an 11-phase machine that can be excited with harmonics up to the ninth. The technique is assessed using both winding function and finite element analysis methods. The prototype machine is fed from an 11-phase inverter. The system DSP control using genetic algorithm produces an optimum flux distribution by using winding sequence and harmonic current injection. Simulation results for the 11-phase dq model and prototype drive experimental results are presented. [ABSTRACT FROM AUTHOR]