Search

Power-electronic-converter-induced motor bearing currents are a widespread problem in the field of electrical drives. Parasitic capacitances between the electrical machine's parts provide a path for leakage currents, which finally harm metallic ball bearings. Remembering that end-windings have a significant contribution in building up stray capacitances, a countermeasure affecting both the lamination stack and end-winding areas is needed. This article focuses on a countermeasure against the noncirculating bearing currents in the cluster of solutions at the motor side. The electrostatic shielding approach, which is a known principle to reduce capacitive couplings, is applied in electrical machines every now and then. In this article, the principle of slot-embedded grounded electrodes is extended to cover also the end-windings. Thus, the electrodes provide a better shaft-to-ground voltage mitigating effect compared to the case where electrodes are applied only in the lamination stack area. The feasibility and effectiveness of such a countermeasure are investigated. Different options in terms of scaling of both the machine size and diameter of the electrodes were analyzed and corresponding conclusions were pointed out. [ABSTRACT FROM AUTHOR]

A direct-on-line synchronous reluctance motor (DOLSynRM) with a rotor topology defined by the natural flux line curve approach is studied as an alternative to an induction motor (IM) using a 1.5 kW, 50 Hz synchronous reluctance motor as an example. If an IM stator is used, a direct squirrel cage rotor replacement by a synchronous reluctance rotor equipped with a damper winding might not guarantee a sufficient starting performance. To ensure the strong enough starting capability, the natural flux line curve approach was modified in the motor design. The proposed approach was applied in the optimization of the DOLSynRM using a genetic algorithm. The optimization results show a clear tendency in the rotor design when trying to achieve a reliable starting capability and to maximize the steady-state performance of the DOLSynRM. Both the stator design and the rotor diameter of the optimized DOLSynRM are different from those of a corresponding squirrel cage IM. A DOLSynRM prototype was built and tested. It showed about a 5.4%-unit higher efficiency than the original prototype IM and acceptable starting performance under the rated load condition. The starting capabilities of the motors under study are considered with different loads. The locked rotor apparent power and current stay below permissible limits in both the IM and the DOLSynRM. [ABSTRACT FROM AUTHOR]

High-speed solid-rotor induction machines (HSIMs) are popular within high-speed (HS) applications because of their high rotor structural integrity and their fairly well-established manufacturing process guaranteeing high quality series products. Designing a new HS electric machine requires a multidisciplinary team to accomplish the machine performance desired. In case of a HS machine design, the components and applied materials often reach their physical limits at the rated operating condition. Therefore, the design process is highly iterative and, thus, a systematic approach has a high potential to reduce the time of the design phase significantly. In this article, a systematic design process is proposed for a modular, multimegawatt (MMW) HSIM with three radial active magnetic bearings. The process includes a traditional multidisciplinary design flow with extra critical aspects of MMW HS machines: manufacturability, bearing system, housing, and operating unit. In addition, the manufactured machine is reported. The proposed systematic design process is described, including several multidisciplinary critical design aspects of HS machinery. [ABSTRACT FROM AUTHOR]

Different mechanisms by which bearing currents flow inside the electrical machine are well studied. In contrast, investigation and development of different techniques to mitigate these currents remain a field for improvement, and the final common solution to the problem has not been provided yet. In pursuit of addressing the problem, this article deals with noncirculating (or capacitive) bearing currents. The circuit mechanism of capacitive currents is explained in brief, and an approach for their mitigation is introduced. This article studies the influence of the stator winding and the slot geometry and presents different geometries to modify the motor to reduce the capacitive bearing currents. The effectiveness of the proposed mitigation technique is shown by finite-element-based modeling and verified by laboratory tests with different induction motor designs, where the winding and magnetic circuit geometries are varied. The technique can be used, in particular, for the mitigation of noncirculating currents, but it also offers potential for further research. [ABSTRACT FROM AUTHOR]

A high demand for electrification of the transport sector has resulted in a need to provide compact and reliable electric power trains where the electric machine is a key element. The cooling system has a strong impact on the specific torque and power capability of the machine. The selection of the cooling solution should not be based on the steady-state cooling performance only but also on the transient characteristics owing to the typical operational load nature of the propulsion system, where the load is not continuous (as it usually is in industrial applications), but it frequently varies in time depending on the vehicle type and the driving style. This article investigates in detail the cooling capabilities of a direct winding liquid cooling solution and compares it with a traditional frame liquid cooling arrangement in the transient condition. As a result of the comparison, it was found that the location of heat removal close to the heat source makes the temperature transient time faster, which allows to apply overload operating points more frequently. [ABSTRACT FROM AUTHOR]

Direct liquid cooling (DLC) of electrical machine windings is a clearly effectual cooling method for high-torque and high-power-density applications needed, especially, in heavy vehicles. Usually, in electric vehicles, the stator copper winding losses are the most dominating losses during the accelerating or decelerating (recuperation) modes, and therefore, traditional windings may heat up significantly during high-torque periods. Removing the heat directly from the winding in which most of the heat is generated allows the most straightforward and effective way of cooling. This paper investigates the feasibility of the DLC in a radial-flux permanent-magnet traction motor. This case provides experimental information of the behavior of the DLC of the windings. The prototype motor equipped with DLC windings is installed in an electric bus so that typical bus load cycles can be tested. [ABSTRACT FROM AUTHOR]

High-speed (HS) electrical machines provide high system efficiency, compact design, and low material consumption. Active magnetic bearings (AMBs) bring additional benefits to the HS system, such as elimination of the friction losses, reduced wear and maintenance, and a built-in monitoring system. HS drivetrains are usually designed for specific applications and require a high level of integration. This paper describes a design method of the HS electrical machine supported by AMBs, considering their mutual influence on the system performance. The optimization procedure, which takes into account both the electrical machine and bearing designs, is developed. The optimization is based on a multiobjective genetic algorithm. The selected optimization parameters include the AMB and machine dimensions. The optimization objectives cover the electrical machine performance and the rotordynamics. The results of the proposed optimization algorithm are implemented in the constructed 350-kW, 15 000-r/min induction machine with a solid rotor supported by AMBs. The prototype tests verify the design and optimization results. [ABSTRACT FROM AUTHOR]

Efficient cooling is needed, for example, in traction motors which face regularly high torque peaks and generate high stator Joule losses. This paper studies the feasibility of the direct liquid cooling in the thermal management of a low-power low-voltage permanent-magnet machine. A tooth-coil axial-flux permanent-magnet double-stator-single-rotor test machine was first equipped with indirect liquid cooling using water cooling jackets and then with direct winding cooling. The winding material used is a hybrid conductor comprising a stainless steel coolant conduit tightly wrapped with stranded Litz wire. The performance of the motor is examined at various power levels using oil or water as the cooling fluid. The results confirm that the proposed direct cooling method is practical also in small machines, and furthermore, it offers significant improvements in the machine thermal management, especially, in cases where stator Joule losses dominate. [ABSTRACT FROM AUTHOR]

This paper evaluates the feasibility of a direct liquid cooling approach in the thermal management of an axial flux permanent-magnet machine. To demonstrate the cooling method, a test motor was fitted with helical tooth coil windings formed from a hybrid conductor comprising a stainless steel coolant conduit tightly wrapped with a stranded Litz wire. The motor is a 100-kW permanent-magnet, axial-flux, double-stator, single-rotor machine. The proof of concept integrated the motor with a closed liquid coolant loop, appropriate instrumentation, and a data acquisition system. The general performance of the motor was examined at various power levels using polyalphaolefin oil as the cooling fluid. The results show the proposed cooling method to be feasible, and furthermore, to provide significant improvements to the machine thermal management. [ABSTRACT FROM PUBLISHER]

High-speed permanent-magnet synchronous machines (HS PMSMs) are a popular topology among modern electrical machines. Suitable applications for such machines are low-power vacuum pumps, compressors, and chillers. This paper describes a systematic design methodology for an HS PMSM using two case studies. The design process for such high-speed (HS) machines is multidisciplinary and highly iterative due to the complex interaction of the many design variables involved. Consequently, no single optimum solution exists, and multiple possible solutions can meet the customer requirements. Practical solutions should be within acceptable thermal limits, should be energy-efficient, and should be rigid enough to withstand the forces exerted during operation. The proposed design flow is divided into steps that are presented in this paper in the form of a flowchart with emphasis on mechanical aspects. Each step represents a task for a thermal, mechanical, or electrical engineer. The features of each step and the prerequisites for moving to the next step are discussed. The described methodology was implemented in the design of two HS PMSMs. The output performance results of the design flow are compared with measured results of the prototypes. The design process described in this paper provides a straightforward procedure for the multidisciplinary design of HS permanent magnet electrical machines. [ABSTRACT FROM PUBLISHER]

Analytical calculation methods for all the major components of the synchronous inductance of tooth-coil permanent-magnet synchronous machines are reevaluated in this paper. The inductance estimation is different in the tooth-coil machine compared with the one in the traditional rotating field winding machine. The accuracy of the analytical torque calculation highly depends on the estimated synchronous inductance. Despite powerful finite element method (FEM) tools, an accurate and fast analytical method is required at an early design stage to find an initial machine design structure with the desired performance. The results of the analytical inductance calculation are verified and assessed in terms of accuracy with the FEM simulation results and with the prototype measurement results. [ABSTRACT FROM PUBLISHER]

Armature-reaction-compensated permanent-magnet synchronous generators are a particular type of hybrid excitation synchronous generators, where the main flux is created by the permanent magnets and the field winding is needed only to compensate the armature reaction. This paper studies the feasibility of an armature-reaction-compensated permanent magnet synchronous generator in island operation by comparison with a conventional electrically excited synchronous generator and permanent magnet synchronous generator. The aim of this paper is to demonstrate the performance of an armature-reaction-compensated permanent magnet synchronous generator and its operation principle in island operation. As part of the study, a 55 kW prototype was built and tested. The experimental results of the prototype are presented. [ABSTRACT FROM PUBLISHER]

Traction motor design significantly differs from industrial machine design. The starting point is the load cycle instead of the steady-state rated operation point. The speed of the motor varies from zero to very high speeds. At low speeds, heavy overloading is used for starting, and the field-weakening region also plays an important role. Finding a suitable field-weakening point is one of the important design targets. At the lowest speeds, a high torque output is desired, and all current reserves of the supplying converter unit are used to achieve the torque. In this paper, a 110-kW 2.5-p.u. starting torque and a maximum 2.5-p.u. speed permanent-magnet traction motor will be studied. The field-weakening point is altered by varying the number of winding turns of machine. One design is selected for prototyping. Theoretical results are verified by measurements. [ABSTRACT FROM PUBLISHER]

New types of heavy litz wires with noninsulated or insulated strands are offered for high-power low-voltage electrical machines, where skin and proximity effects can cause serious problems if traditional windings are used. This paper evaluates the ac resistance of a litz wire and its usability in megawatt-range low-voltage electrical machines. The evaluation is made by finite-element analysis and by resistance measurements with an experimental test setup. A simple amplifier configuration was used to minimize current and voltage phase shift errors, which are critical in this kind of low-impedance and low-frequency measurement. A simple measurement device based on the aforementioned configuration was prepared to ensure a precise measurement result. Tests were done in a frequency range of 50–200 Hz, to cover a wide range of practical high-power low-voltage electrical machines. It is found that the measured litz wire with originally noninsulated strands can be used in large electrical machines up to about 120 Hz if about 50% increase in ac resistance compared to the dc resistance is allowed. Impregnation of the originally noninsulated litz wire with vacuum pressure impregnation improved the ac resistance in one test case, and in the other case, it seemed to have no effect on the ac resistance. [ABSTRACT FROM AUTHOR]

This paper provides design guidelines for the passive LC filters. Based on these guidelines, a method to design a new type of a passive filter, called hybrid LC filter, is proposed. A filter design example accompanies the considerations; simulation and test results of the proposed filter in time and frequency domains are shown. [ABSTRACT FROM PUBLISHER]

The influence of slot-and-pole-number combinations on the leakage inductance of double-layer fractional-slot concentrated nonoverlapping winding (i.e., tooth-coil winding) permanent-magnet synchronous machines is studied. A Fourier-analysis-based method for calculating the harmonic air-gap leakage inductance applied to the current-linkage waveform (winding function) in the air gap is suggested. Different slot-and-pole combinations are considered, and their influence, in particular, on the air-gap leakage inductance is indicated. In tooth-coil machines, the air-gap harmonic leakage can have a surprisingly large impact on the machine performance. [ABSTRACT FROM PUBLISHER]

Analytical calculation of circulating and eddy currents in windings has been under research for almost a century, yet the calculation accuracy has improved slowly. However, over the recent years, the development of finite-element methods (FEM) has boosted the research. A lot of effort has been taken to calculate the ac resistance losses in transformers in the past, whereas rotating electrical machines have received less attention. These models have not taken the end-winding effect into account. In this paper, 2-D FEM results are compared with analytical equations. Based on these results, a more accurate model compared with Dowell's model for single-layer form-wound windings used in electrical machines is developed empirically, and the end winding resistance is analytically taken into account in the results. A maximum error of 5% is achieved in the range of 0–200 Hz for a single-layer form-wound winding. [ABSTRACT FROM PUBLISHER]

Permanent magnet synchronous machines (PMSM) are considered a viable option in various types of applications. However, particularly in consumer and low-power industrial applications, the price may be a factor that limits the use of PMSMs. In addition to a different technology, the main reason for the high price of PMSMs is the use of expensive neodymium or samarium-cobalt magnets. Their use is necessary only if a high motor torque T to linear current density A ratio (T/A) is required. Ferrite permanent magnets are low cost, abundant, and have negligible eddy current losses in low-frequency applications such as motor drives. They have a much lower energy product (BH\max) than the most modern magnets. Because of the high prices of rare earth magnets, many parties are seeking for opportunities to use ferrites instead. In the case of rotor surface ferrite magnets, the air gap flux density remains low. The air gap torque producing tangential Maxwell stress is proportional to the product of the air gap flux density B\delta[ \Vs/m^2] and the linear current density A [A/m]. If the flux density is low and A cannot be increased, the rotor has to be made larger than in machines having a high air gap flux density. In the case of multiple pole machines, the outer rotor approach, with its low rotor yoke height, offers an interesting alternative. The air gap diameter of these machines can be made larger than in conventional inner rotor type motors without increasing the machine outer dimensions. In this paper, an outer rotor PMSM with ferrite magnets is analyzed and tested. The machine characteristics in a fan drive are compared with an induction machine of the same power. [ABSTRACT FROM PUBLISHER]

This paper deals with the design of permanent magnet synchronous motors (PMSMs) with ferrite magnets and their comparison with synchronous machines with NdFeB magnets. In recent years, ferrite magnets have become popular due to their rather low cost and, what is more important, due to increasing of the NdFeB magnets cost last time. The progress in ferrite magnet material properties during the latest decade gave rise to their use in high power applications. Their remanent flux density today reaches values beyond 0.4 T, which allows design electrical machines with acceptable performance. In this paper, three designs of ferrite machines are presented and compared with a real PMSM with NdFeB magnets. Furthermore, the influence of the stator winding type and the shape of the slot opening on the PMSM properties will be demonstrated. All machines are designed for the same output power as the original PMSM with NdFeB magnets. This paper demonstrates that ferrite magnets can, to some extent, be used as replacements for the NdFeB magnets in high-efficiency power applications. [ABSTRACT FROM AUTHOR]