Search

A non-contact interface for modular smartphones that can provide a data connection at a maximum MIPI rate of 6 Gb/s has been developed. A two-fold transmission line coupler, which is a small-size coupler that has a wide bandwidth, is proposed for modular smartphones, where the layout area is strictly limited. The coupler size is 6 mm2 for a 5 mm communication distance, which is 1/24 smaller than the conventional coupler. Since many wireless communication components, such as LTE, WiFi, and GPS transceivers, are assembled in a small module, the interference between the non-contact interface and the wireless transceivers should be suppressed. To improve noise immunity and reduce unwanted radiation from the coupler, an electromagnetic-compatibility robust pulse transceiver is proposed. A synchronous receiver using an edge counting clock recovery circuit improves noise immunity, and a bi-phase pulse transmitter reduces noise radiation in the GPS band. There is no EMS by LTE or WiFi signals on the data connection at BER < 10^-12 when the coupler is separated by a distance of 2 mm and no EMI on GPS signals at a separation of 10 mm. Compared with the state-of-the-art result, the highest energy efficiency (6 pJ/b) and space efficiency (1.2 \textmm^2/1 \textmm distance) is achieved. [ABSTRACT FROM PUBLISHER]

A highly reliable wireless solid-state drive (SSD) system for future applications of large volume storage is presented. The wireless interface in the system consists of an inductively coupled power link with fast transmission power control and high-speed data links using transmission line couplers (TLCs). The wireless power link can deliver 1 W from the host to the SSD. The full duplex wireless data interface achieves raw data rate of 1.6 Gb/s. The reliability of the wireless interface is studied though simulation analysis and experiments. The error correction block for the NAND flash memory system can also correct errors in the wireless data links, allowing the requirements for the PHY layer to be relaxed. The error correction code is discussed, including optimization by analyzing the error bits on the wireless data links. The experimental results confirmed strong tolerance to the interference from the power link on the wireless data link, and the water proof property of both the data and power links. [ABSTRACT FROM PUBLISHER]

Wireless 3-D network-on-chips (NoCs) with inductive-coupling ThruChip interfaces provide a large degree of flexibility for customizing the number of arbitrary chips in a package after chips have been fabricated. To simplify the vertical communication interfaces, static time division multiple access (TDMA) is used for the vertical broadcast buses, while arbitrary or customized topologies can be used for the intrachip network. This paper proposes two techniques to break through the simple static TDMA-based vertical buses while maintaining a simple communication interface. The first technique is headfirst sliding (HS) routing to reduce the waiting time for acquiring the communication time-slot. HS routing selects the best vertical bus based on the current time, taking advantage of static TDMA. The second technique extends carrier sense multiple access with collision detection (CSMA/CD) for vertical broadcast buses. We introduce a packet collision detection technique for inductive-coupling buses and propose two retransmission strategies to reduce the waiting time for packet retransmissions caused by collisions. Network simulation results show that HS routing reduces the communication latency by 39.1% compared with the conventional static TDMA bus-based 3-D NoC that uses the shortest path routing. The proposed CSMA/CD bus also improves the latency by 52.5% and throughput by 34.1%. The full-system simulation results show that HS routing and the proposed CSMA/CD technique reduce the application execution time accordingly while maintaining the average flit transfer energy overhead modest. [ABSTRACT FROM AUTHOR]

A wireless 3D NoC architecture is described for building-block SiPs, in which the number of hardware components (or chips) in a package can be changed after chips have been fabricated. The architecture uses inductive-coupling links that can connect more than two examined dies without wire connections. Each chip has data transceivers for the uplink and downlink in order to communicate with its neighboring chips in the package. These chips form a vertical unidirectional ring network so as to fully exploit the flexibility of the wireless approach that enables us to add, remove, and swap the chips in the ring. To avoid protocol and structural deadlocks in the ring, we use bubble flow control, which does not rely on the conventional VC-based deadlock avoidance mechanism. In addition, we propose a bidirectional communication scheme to form a bidirectional ring network by using the inductive-coupling transceivers that can dynamically change the communication modes, such as TX, RX, and Idle modes. This paper illustrates the inductive-coupling transceiver circuits, which can carry high data transfer rates of up to 8 Gbps per channel, for the wireless 3D NoC. It also illustrates an implementation of a wireless 3D NoC that has on-chip routers and transceivers implemented with a 65 nm process in order to show the feasibility of our proposal. The vertical bubble flow control and conventional VC-based approach on the uni- and bidirectional ring networks are compared with the vertical broadcast bus in terms of throughput, hardware amount, and application performance using a full system multiprocessor simulator. The results show that the proposed bidirectional communication scheme efficiently improves application performance without adding any inductive-coupling transceivers. In addition, the proposed vertical bubble flow network outperforms the conventional VC-based approach by 7.9-12.5 percent with a 33.5 percent smaller router area for building-block SiPs connecting up to eight chips. [ABSTRACT FROM PUBLISHER]

This paper presents SD-card-size wireless power transfer system for large-volume contactless memory cards. Voltage is boosted simultaneously with power transfer, which eliminates the dc–dc converter or charge-pump circuit for data write operation into the flash memory chip. The proposed approach reduces the number of components and BOM cost and improves the total power efficiency. A vector summing technique is proposed to control the transmitting power and secondary side voltage. The transmitter and rectifier have been designed and fabricated using 0.18-\mum-CMOS with high voltage option. Voltage boost from 3.3 to 16.3 V and 1-W power transfer with 50% total efficiency have been successfully demonstrated, and the response time for the power control loop is shorter than 35 \mu\s. [ABSTRACT FROM PUBLISHER]

This paper presents a low-power inductive-coupling link in 90-nm CMOS. Our newly proposed transmitter circuit uses a charge-recycling technique for power-aware 3-D system integration. The cross-type daisy chain enables charge recycling and achieves power reduction without sacrificing communication performance such as a high timing margin, low bit error rate and high bandwidth. There are two design issues in the cross-type daisy chain: pulse amplitude reduction and another is inter-channel skew. To compensate for these issues, an inductor design and a replica circuit are proposed and investigated. Test chips were designed and fabricated in 90-nm CMOS to verify the validity of the proposed transmitter. Measurements revealed that the proposed cross-type daisy chain transmitter achieved an energy efficiency of 65 fJ/bit without degrading the timing margin, data rate, or bit error rate. In order to investigate the compatibility of the transmitter with technology scaling, a simulation of each technology node was performed. The simulation results indicate that the energy dissipation can be potentially reduced to less than 10 fJ/bit in 22 nm CMOS with proposed cross-type daisy chain. [ABSTRACT FROM AUTHOR]

In this paper, we report the world's first ac-coupled clock distribution circuit for low-power and high-frequency clock distribution. By employing the proposed ac-coupled LC-based voltage-controlled oscillator (LC-VCO) and phase interpolators, the use of conventional current-mode-logic (CML) buffers with large power requirements can be prevented, and power consumption for clock distribution can be reduced. With the aim of verifying the effectiveness of the proposed circuit, test chips were designed and fabricated in 0.18-\mum mixed-signal CMOS technology. The measured results indicated a 14.007 GHz clock distribution to four points whose pitches are 450 \mum, with 6.9 mW of power. The phase noise was measured to be -79.06 dBc/Hz at a 100 kHz offset, -101.66 dBc/Hz at a 1 MHz offset, and -107.25 dBc/Hz at a 10 MHz offset, with a clock frequency of 12.96 GHz. Furthermore, a phase averaging technique for reducing phase deviation was proposed and theoretically investigated. [ABSTRACT FROM PUBLISHER]