Search

Improving channel utilization is a well-known issue in wireless networks. In traditional point-to-point wireless communication, significant efforts had been made by the existing studies on enhancing the utilization of the channel access time. However, in the emerging wireless network using MU-MIMO, considering only the time domain in channel utilization is not sufficient. As multiple transmitters are allowed to transmit packets simultaneously to the same AP, allowing more antennas at AP would lead to higher channel utilization. Thus, the channel utilization in MU-MIMO should consider both time and spatial domains, i.e., the channel access time and the antenna usage, which have not been considered in the existing methods. In this paper, we point out that the fundamental problem is lacking of the antenna information of contention nodes in channel contention. To address this issue, we propose a new MAC-PHY architecture design, CUTS, to allow distributed nodes effectively contend for the channel and utilize the channel in both domains. Particularly, CUTS adopts interference nulling to attach the antenna information in channel contention. Meanwhile, techniques such as channel contention in frequency domain and ACK in frequency domain using self-jamming are adopted. Through the software defined radio-based real experiments and extensive simulations, we demonstrate the feasibility of our design and illustrate that CUTS provides better channel utilization with the gain over IEEE 802.11 reaching up to 470 percent. [ABSTRACT FROM AUTHOR]

Leveraging concurrent transmission is a promising way to improve throughput in wireless networks. Existing media access control (MAC) protocols like carrier sense multiple access always try to minimize the number of concurrent transmissions to avoid collision, although collisions at sender sides are harmless to the overall performance. The reason for such conservative strategy is that those protocols cannot obtain accurate channel status (who is transmitting and receiving) with low cost. They can only avoid potential collisions through rough channel status (idle or busy). To obtain additional information in a cost-efficient way, we propose a novel coding scheme, Attachment Coding, to allow control information to be “attached” on data packet. Nodes then transmit two kinds of signals simultaneously, without degrading the effective throughput of the original data traffic. Based on Attachment Coding, we propose an Attached-RTS MAC (AR-MAC) to exploit exposed terminals for concurrent transmissions. The attached control information provides accurate channel status for nodes in real time. Therefore, nodes can identify exposed terminals and utilize them for concurrent transmission. We theoretically analyze the feasibility of Attachment Coding, and implement it on the GNU Radio testbed to further verify it. We also conduct extensive simulations to evaluate the performance of Attached-RTS. The experimental results show that by leveraging Attachment Coding, AR-MAC achieves up to 180 percent in dense deployed ad hoc networks. [ABSTRACT FROM AUTHOR]

Wi-Fi, which enables convenient wireless access to Internet services, has become integral to our modern lives. With widely-deployed Wi-Fi infrastructure, modern people can enjoy a variety of online services such as web browsing, online shopping, social interaction, and e-commerce almost at any time and any place. Traditionally, the most significant functionality of Wi-Fi is to enable high-throughput data communication between terminal devices and the Internet. However, beyond that, we observe that a novel type of system based on commodity Wi-Fi is increasingly attracting intense academic interest. Without hardware modification and redeployment, researchers are exploiting channel state information output by commodity Wi-Fi and transforming existing Wi-Fi systems into radar-like ones that can recognize human behavior along with data communication. This fancy functionality is tremendously expanding the boundaries of Wi-Fi to a new realm and triggering revolutionary applications in the context of the Internet of Things. In this article, we provide a guide to and introduce the impressive landscape of this new realm. [ABSTRACT FROM AUTHOR]

This paper applies the wireless powered communication network (WPCN) to an indoor communication system with two energy harvesting (EH) enabled users. Unlike the existing WPCN works designed for outdoor communications, where each user harvests energy only from the signals transmitted by a dedicatedly deployed hybrid access point (H‐AP), due to the short device‐to‐device distance in the indoor scenario, each user additionally harvests a sufficient amount of energy from the information signals transmitted by the H‐AP and the other user. First, the joint downlink and uplink throughput are maximized for the wireless powered indoor communication system. This problem is non‐convex. Thus, the authors manage to transform this problem into a convex one and solve it using convex optimization techniques. The solutions reveal that the total throughput increases largely over a reduced device‐to‐device distance due to the resultant harvested energy from both energy and information signals at each user. However, an unfair downlink versus uplink rate allocation phenomenon is observed. Thus, considering the importance of uplink communication quality for various indoor applications, a new problem is further proposed to maximize the uplink sum‐throughput over both users with an additional constraint to ensure a sufficient downlink rate. This problem is also shown to be non‐convex and is solved optimally by using a method similar to that in the first problem. Numerical results demonstrate the effectiveness of the proposed approach for improving the downlink versus uplink rate allocation fairness in the indoor wireless‐powered communication system. [ABSTRACT FROM AUTHOR]

To accommodate the soaring mobile broadband traffic, the Federal Communications Commission (FCC) in the U.S. sets out to retrieve under-utilized spectrum (e.g., TV Whitespace) and lay the groundwork for spectrum redistribution. Auction is an efficient way to allocate resources to those who value them the most. The large pool of spectrums to be released, especially the ones in TV Whitespace, consist of wide-range frequencies. Apart from spatial reuse, spectrum heterogeneity imposes new challenges for spectrum auction design: 1) Wireless service providers with different targeted cell coverages have different spectrum frequency preferences; 2) interference relationship is frequency-dependent due to frequency-selective signal fading. Unfortunately, existing spectrum auction mechanisms either assume spectrum valuation is homogeneous or use homogeneous interference graph to group buyers who can reuse the same spectrum. In this paper, we propose TAMES, an auction framework for heterogeneous spectrum transaction. We consider a multi-seller-multi-buyer double auction, in which every buyer submits a bid, consisting of the spectrum demand and a bidding profile of prices for spectrums contributed by all sellers. A novel buyer grouping approach is proposed to tackle the problem of heterogeneous interference graph. TAMES is proved to be truthful as well as individually rational. The simulation results show that TAMES significantly improves spectrum utilization, sellers' revenue and buyers' utility by making smart use of spectrum heterogeneity, while keeping low running time comparable with existing auction mechanisms. Moreover, via simulation, we show how to help buyers obtain continuous spectrums which further improves buyers' satisfaction. [ABSTRACT FROM AUTHOR]

Radio frequency (RF) based technologies play an important role in indoor localization, since Radio Signal Strength (RSS) can be easily measured by various wireless devices without additional cost. Among these, radio map based technologies (also referred as fingerprinting technologies) are attractive due to high accuracy and easy deployment. However, these technologies have not been extensively applied on real environment for two fatal limitations. First, it is hard to localize multiple objects. When the number of target objects is unknown, constructing a radio map of multiple objects is almost impossible. Second, environment changes will generate different multipath signals and severely disturb the RSS measurement, making laborious retraining inevitable. Motivated by these, in this paper, we propose a novel approach, called Line-of-sight radio map matching, which only reserves the LOS signal among nodes. It leverages frequency diversity to eliminate the multipath behavior, making RSS more reliable than before. We implement our system MODLoc based on TelosB sensor nodes and commercial 802.11 NICs with Channel State Information (CSI) as well. Through extensive experiments, it shows that the accuracy does not decrease when localizing multiple targets in a dynamic environment. Our work outperforms the traditional methods by about 60 percent. More importantly, no calibration is required in such environment. Furthermore, our approach presents attractive flexibility, making it more appropriate for general RF-based localization studies than just the radio map based localization. [ABSTRACT FROM AUTHOR]

Ambient backscatter communication (AmBC) has emerged as a promising paradigm for enabling sustainable low-power operation of Internet of Things devices. This is due to its ability to enable sensing and communication through backscattering ambient wireless signals (e.g., WiFi and TV sig-nals). But a great impediment to AmBC-enabled networks is the difficulty in decoding the backscat-ter signals because the ambient signals are usually modulated and meant for other legacy receivers rather than AmBC devices. Drawing from the ability of machine learning (ML) to enhance the performance of wireless communication systems, some ML-aided techniques have been developed to assist signal detection in AmBC. Hence, this article aims to provide a comprehensive overview of the subject by describing the operation of the AmBC network, highlighting the major challenges to signal detection in AmBC, discussing and com-paring the performance of some existing ML-assisted solutions to AmBC signal detection, and highlighting some future research that could be carried out on the subject. [ABSTRACT FROM AUTHOR]

UAV aided communication technology holds tremendous potential to upgrade outdoor link throughput and provide on-demand wireless services. The flexible deployment characteristic makes UAV-aided networks competent at emergency situations, including natural disasters and sudden traffic hotspots. In this backdrop, UAVs are required to be densely deployed to accommodate the huge volume of data traffic, where interference amid the neighboring cells turns out to be extremely challenging. To break this stalemate, this article systematically investigates spectrum sharing technology for ultra-dense UAV-aided networks from the architecture level down to the physical layer. We shed light on design principles and key challenges in utilizing overlapped spectrum for interference-enabled concurrent transmissions. With these principles in mind, we introduce SpecShare, which utilizes coding redundancy at the PHY layer for UAV spectrum sharing. We explore the optimal UAV placement strategy in the network layer to fully unleash the potential of such spectrum sharing capacity. We discuss the feasibility of SpecShare, and demonstrate its effectiveness in terms of network throughput. [ABSTRACT FROM AUTHOR]