Search

Soft-switching inverters can achieve high efficiencies and low switchdv/dtanddi/dt, but often impose additional stress on the switches due to their resonant behavior. Multicell converters, on the other hand, can process high voltages by arranging the switches to share the stress. This paper proposes a buck–boost multicell soft-switching inverter with inherent cell voltage balancing. Both the current and voltage stresses are shared by the cells. Soft-switching conditions are achieved for all switching transitions without any need for auxiliary circuitry or clamps. A multiple-winding transformer transfers energy between the terminals and provides galvanic isolation. An analytical study and experimental results on a 1200-W prototype verify the operation of the inverter. [ABSTRACT FROM AUTHOR]

This paper presents a novel single-stage soft-switched high-frequency-link three-phase dc–ac converter topology. The topology supports unidirectional dc to ac power flow and is targeted for applications like grid integration of photovoltaic sources, fuel cell, etc. The high frequency magnetic isolation results in reduction of system volume, weight, and cost. Sine-wave pulsewidth modulation is implemented in dc-side converter. Though high-frequency switched, dc-side converter is soft switched for most part of the line cycle. The ac-side converter active switches are line frequency switched incurring negligible switching loss. The line frequency switching of ac-side converter facilitates use of high voltage blocking inherently slow semiconductor devices to generate high voltage ac output. In addition, a cascaded multilevel structure is presented in this paper for direct medium-voltage ac grid integration. A detailed circuit analysis considering nonidealities like transformer leakage and switch capacitances, is presented in this paper. A 6-kW three-phase laboratory prototype is built. The presented simulation and experimental results verify the operation of the proposed topologies. [ABSTRACT FROM AUTHOR]

A new zero-voltage-switching (ZVS) push-pull pulse-width modulation (PWM) converter is proposed in this paper. The wide ZVS condition for all of the switches is obtained by utilizing the energy stored in the output inductor and magnetizing inductance. As a result, the switching losses can be dramatically reduced. A simple auxiliary circuit including two small diodes and one capacitor is added at the secondary side of a high frequency (HF) transformer to reset the primary current during the circulating stage and to clamp the voltage spike across the rectifier diodes, which enables the use of low-voltage and low-cost diodes to reduce the conducting and reverse recovery losses. In addition, there are no active devices or resistors in the auxiliary circuit, which can be realized easily. A detailed steady operation analysis, characteristics, design considerations, experimental results and a loss breakdown are presented for the proposed converter. A 500 W prototype has been constructed to verify the effectiveness of the proposed concept. [ABSTRACT FROM AUTHOR]

This paper presents a single-stage bidirectional high-frequency transformer (HFT) link dc/ac converter topology for a three-phase adjustable magnitude and frequency PWM ac drive. This type of converters find a wide range of applications including UPS systems, drives involving renewable energy sources (Solar, Fuel cell), and energy storage systems (typically low voltage dc to high voltage PWM ac). The HFT results in reduction in cost and weight along with a considerable increase in power density. The adverse effects of common-mode voltage are well known in this kind of applications. The proposed topology along with a modulation technique reduces common-mode voltage to practically zero and generates high-quality output voltage waveform comparable to conventional space vector PWM (CSVPWM). A source-based commutation method, presented in this paper, to commute the energy stored in the leakage inductance of the HFT resulting in the following advantages 1) no need for any auxiliary circuits with passive components; 2) almost complete recovery of the leakage energy; 3) soft switching of the output side converter for all load conditions; and 4) minimization of common-mode voltage switching due to commutation. The converter along with the suggested control has been analyzed in detail. The presented simulation and experimental results confirm the operation of the proposed converter. [ABSTRACT FROM AUTHOR]

This letter presents a new zero-voltage-switching (ZVS) isolated dc–dc converter which combines a boost half-bridge (BHB) cell and a full-bridge (FB) cell, so that two different type of power sources, i.e., both current fed and voltage fed, can be coupled effectively by the proposed converter for various applications, such as fuel cell and supercapacitor hybrid energy system. By fully using two high- frequency transformers and a shared leg of switches, number of the power devices and associated gate driver circuits can be reduced. With phase-shift control, the converter can achieve ZVS turn-on of active switches and zero-current switching (ZCS) turn-off of diodes. In this letter, derivation, analysis, and design of the proposed converter are presented. Finally, a 25–50 V input, 300–400 V output prototype with a 600 W nominal power rating is built up and tested to demonstrate the effectiveness of the proposed converter topology. [ABSTRACT FROM AUTHOR]

This paper presents the design of new high-frequency transformer isolated bidirectional dc-dc converter modules connected in input-series-output-parallel (ISOP) for 20-kVA-solid-state transformer. The ISOP modular structure enables the use of low-voltage MOSFETs, featuring low on-state resistance and resulted conduction losses, to address medium-voltage input. A phase-shift dual-half-bridge (DHB) converter is employed to achieve high-frequency galvanic isolation, bidirectional power flow, and zero voltage switching (ZVS) of all switching devices, which leads to low switching losses even with high-frequency operation. Furthermore, an adaptive inductor is proposed as the main energy transfer element of a phase-shift DHB converter so that the circulating energy can be optimized to maintain ZVS at light load and minimize the conduction losses at heavy load as well. As a result, high efficiency over wide load range and high power density can be achieved. In addition, current stress of switching devices can be reduced. A planar transformer adopting printed-circuit-board windings arranged in an interleaved structure is designed to obtain low core and winding loss, solid isolation, and identical parameters in multiple modules. Moreover, the modular structure along with a distributed control provides plug-and-play capability and possible high-level fault tolerance. The experimental results on 1 kW DHB converter modules switching at 50 kHz are presented to validate the theoretical analysis. [ABSTRACT FROM AUTHOR]