Search

Abstract: This paper reports R&D progress of the MeV class accelerator, beam focussing technique and a high voltage (HV) bushing toward the ITER Neutral Beam system at JAEA. A H− ion beam of 320mA (current density: 140A/m2) was successfully accelerated up to 796keV by fixing air leak in the ion source chamber caused by heat loading due to backstream positive ions. From analyses of a three-dimensional beam trajectory, a countermeasure against beamlet deflection due to space charge repulsion among beamlets was identified to compensate the deflection by proper aperture offset in the electron suppression grid. For development of the HV bushing, a half-size (Ø800mm) mockup single stage bushing was manufactured and tested, that demonstrated the dc voltage holding capability of up to 220kV in a condition with vacuum inside. Electrostatic analyses and design of the HV bushing are in progress, in which some design improvements are suggested to reduce electric field strength on the surface of ceramic insulator. [Copyright &y& Elsevier]

• Joint experimental campaigns carried out in QST lab in Naka, Ibaraki, Japan. • Full compensation of magnetic criss-cross deflection of beamlets obtained. • Non-uniform extraction assumed for interpreting the experimental results. • Numerical simulations can reproduce the experimental results with good accuracy. In the framework of the collaboration between Consorzio RFX (Padova, Italy) and QST (Naka, Japan) two experimental campaigns have been organized on the Negative Ion Test Stand (NITS) in Naka, employing an ITER-like multi-beamlet configuration. These campaigns were aimed at compensating for the undesired magnetic deflection of the ion beam. The experiments have clarified the influence of operating parameters on the optical properties of the ion beam. The physical phenomena acting on the optics have been investigated, in particular the effect of an asymmetry of the ion current density at meniscus. Comparisons with simulations have been made and the modeling has been improved consequently. During the second experimental campaign, a perfect compensation of the ion deflection has been achieved. [ABSTRACT FROM AUTHOR]

The long-pulse acceleration of the high-power positive ion beam has been demonstrated with the JT-60 positive ion source in the joint experiment among Japan Atomic Energy Agency (JAEA), Korea Atomic Energy Research Institute (KAERI) and National Fusion Research Institute (NFRI) under the collaboration program for the development of plasma heating and current drive systems. In this joint experiment, the increase of the heat load and the breakdowns induced by the degradation of the beam optics due to the gas accumulation was one of the critical issues for the long-pulse acceleration. As a result of development of the long-pulse operation techniques of the ion source and facilities of the neutral beam test stand in KAERI, 2 MW 100 s beam has been achieved for the first time. The achieved beam performance satisfies the JT-60SA requirement which is designed to be a 1.94 MW ion beam power from an ion source corresponding to total neutral beam power of 20 MW with 24 ion sources. Therefore, it was found that the JT-60 positive ion sources were applicable in the JT-60SA neutral beam injectors. Moreover, because this ion source is planned to be a backup ion source for KSTAR, the operational region and characteristic has been clarified to apply to the KSTAR neutral beam injector. [ABSTRACT FROM AUTHOR]

A plasma generator for a long pulse H+/D+ ion source has been developed. The plasma generator was designed to produce 65 A H+/D+ beams at an energy of 120 keV from an ion extraction area of 12 cm in width and 45 cm in length. Configuration of the plasma generator is a multi-cusp bucket type with SmCo permanent magnets. Dimension of a plasma chamber is 25 cm in width, 59 cm in length, and 32.5 cm in depth. The plasma generator was designed and fabricated at Japan Atomic Energy Agency. Source plasma generation and beam extraction tests for hydrogen coupling with an accelerator of the KSTAR ion source have been performed at the KSTAR neutral beam test stand under the agreement of Japan-Korea collaborative experiment. Spatial uniformity of the source plasma at the extraction region was measured using Langmuir probes and ±7% of the deviation from an averaged ion saturation current density was obtained. A long pulse test of the plasma generation up to 200 s with an arc discharge power of 70 kW has been successfully demonstrated. The arc discharge power satisfies the requirement of the beam production for the KSTAR NBI. A 70 keV, 41 A, 5 s hydrogen ion beam has been extracted with a high arc efficiency of 0.9 -1.1 A/kW at a beam extraction experiment. A deuteron yield of 77% was measured even at a low beam current density of 73 mA/cm2. [ABSTRACT FROM AUTHOR]

Abstract: IRFM (CEA Cadarache) and JAEA Naka have entered into a collaboration in order to test a Single Gap, Single Aperture (SINGAP) [H.P.L. de Esch, R.S. Hemsworth, P. Massmann, Updated physics design ITER-SINGAP accelerator, Fusion Eng. Des. 73 (2005) 329.] accelerator at the JAEA Megavolt Test Facility (MTF) at Naka, Japan. Whereas at the CEA testbed the acceleration current was limited to 0.1A, at JAEA 0.5A is available. This allows the acceleration of 15 H− beamlets in SINGAP to be tested and a direct comparison between SINGAP and Multi Aperture, Multi Grid (MAMuG) [M. Taniguchi, T. Inoue, N. Umeda, M. Kashiwagi, K. Watanabe, H. Tobari, M. Dairaku, K. Sakamoto, Acceleration of ampere class H− ion beam by MeV accelerator, Rev. Sci. Instrum. 79 (2008) 02C110.] to be made. High voltage conditioning in the SINGAP configuration has been quite slow, with 581kV in vacuum achieved after 140h of conditioning. With 0.25Pa of H2 gas present in the accelerator 787kV could be achieved. The conditioning curve for MAMuG is 200kV higher. SINGAP beam optics appears in agreement with calculation results. A beamlet divergence better than 5mrad was obtained. SINGAP accelerates electrons to a higher energy than MAMuG. Measurements of the power intercepted on one of the electron dumps have been compared with EAMCC code [G. Fubiani, H.P.L. de Esch, A. Simonin, R.S. Hemsworth, Modeling of secondary emission processes in the negative ion based electrostatic accelerator of the International Thermonuclear Experimental Reactor, Phys. Rev. ST Accel. Beams 11 (2008) 014202.] calculations. Based on the experiments described here, electron production by a SINGAP accelerator scaled up to ITER size was estimated to be too high for comfort. [Copyright &y& Elsevier]

• Experimental campaign on MTF carried out in QST lab in Naka, Ibaraki, Japan. • Opera, SLACCAD, COMSOL, EAMCC3D correctly predict beam divergence. • Semi-empirical Opera model with current density asymmetry correctly predicts the beam deflection. • COMSOL and EAMCC3D slightly underestimate heat loads on the grids. It is a widely recognized phenomenon that, in negative ion sources for NBI, the magnetic fields in the source cause an asymmetry of the current density at the meniscus, which affects the beam optics. In order to achieve a more realistic estimation of the negative ion beam optics, the ion current density profile at the beamlet meniscus is sometimes assumed to be non-symmetric with respect to the beamlet axis. The new hypothesis tested in this paper is an empirical law obtained by recent investigations on a similar Kamaboko ion source, which relates this asymmetry to the magnetic field strength at the meniscus and to the power injected in the ion source. For the first time this hypothesis is used to directly and correctly predict the value of the beamlet deflection. The MeV ion source Test Facility (MTF) is a high voltage negative ion beam accelerator dedicated to fusion experiments in QST, Naka, Ibaraki, Japan. MTF can be operated as a three- or five-stage multi-aperture accelerator with a configuration and beam energy comparable to the future ITER NBI. In 2019, experiments were conducted on MTF aiming at accelerating a H- beam with high energy and good optics for a long duration of the beam (around 100 s). These experiments allowed to measure the beamlet divergence and deflection as well as the heat loads due to particle impinging on the accelerator grids, over a wide range of operating parameters. The predictions of several beam simulation codes (Opera, COMSOL, SLACCAD, EAMCC3D) have been compared to the experimental measurements, which allows to obtain a good agreement in terms of beam optics and a fair agreement in terms of heat loads. [ABSTRACT FROM AUTHOR]