Search

This paper proposes an improved zero-current distortion compensation (IZCDC) method for the Vienna rectifier. The conventional zero-current distortion compensation (ZCDC) method modifies the reference voltages by adding an offset voltage to compensate for the zero-current distortion (ZCD). However, the reference voltages occasionally exceed the linear modulation region by the offset voltage added at the driving start-point of the Vienna rectifier, where the modulation index of phase voltage is relatively large. This causes a hard-start of the Vienna rectifier accompanied by a serious surge and distortion in the phase current. In this paper, the IZCDC method is proposed for achieving the soft-start of the Vienna rectifier. When the overmodulation occurs, the proposed method modifies the conventional offset voltage to the IZCDC component, which is involved in the adjustment of the variance of the phase current, only for a certain phase among the three phases. As the IZCDC component regulates the variance of the phase current to zero, surge and distortion in the phase current can be mitigated. As a result, the Vienna rectifier starts its operation softly while ensuring its normal operation in the transients. The effectiveness of the proposed method is verified through simulations and experimental results. [ABSTRACT FROM AUTHOR]

The Vienna rectifier can produce three voltage levels, however only the connection to the neutral-point is fully controllable using the bidirectional switches. When the neutral-point voltage is not imposed in a phase-leg, the polarity of the pulses generated depends on the diode that is conducting in that phase-leg, which is defined by the current direction. As a result, the voltage pulses generated can go in the opposite direction to what is demanded by the controller, and the current becomes distorted. This can be mitigated by injecting a particular zero sequence so that the reference voltage is clamped to the neutral-point during the intervals, where the current of a phase-leg has the opposite sign than its reference voltage. However, the converter is at risk of entering into overmodulation when operating with high modulation indices. In this article, a hybrid modulation strategy is introduced where a calculated minimal amount of reactive current depending on the operating conditions is injected to avoid overmodulation. The reduction of reactive current required compared to the state-of-the-art solutions is up to 100% in certain operating conditions. With the proposed method, the Vienna rectifier can operate in a wide range of power factors without compromising the quality of the source currents. The concept is verified by simulation and in a 1-kW Vienna rectifier experimental setup. [ABSTRACT FROM AUTHOR]

Vienna rectifier is widely employed in the electric vehicle charging system and wind turbine system due to its higher efficiency and lower total harmonic distortion. However, the Vienna rectifier with the LCL filter has the challenge of resonant current mitigation, current zero-crossing distortion elimination, neutral point (NP) voltage balance and switching loss reduction. Moreover, these problems are mutually coupled. To overcome these issues, the causes of resonant current with the conventional discontinuous pulsewidth modulation (PWM) (DPWM) method is analyzed, which reveals that the abrupt change of reference voltage has a wide range harmonics band and easily induces the resonant current at resonant frequency. Then, based on the analysis, a novel three-layer DPWM method with three offset voltages injection is proposed. In the first layer, the NP voltage balance is realized by injecting the first offset voltage. In the second layer, the second offset voltage, which makes the discontinuous reference voltages smooth is presented to reduce the losses and suppress the resonant current. In the third layer, the third offset voltage is elaborated to eliminate current zero-crossing distortion caused by different power factor and the LCL filter. Based on the proposed method, resonant current mitigation, current zero-crossing distortion elimination, NP voltage balance are realized simultaneously with reduced switching losses. The effectiveness and performance of the proposed method are verified by simulation and experiment. [ABSTRACT FROM AUTHOR]

This article proposes a harmonic voltage injection pulsewidth modulation (PWM) method for a Vienna rectifier with an LCL filter. Existing PWM methods for Vienna rectifiers with full power factor can lead to resonance problems. It generates current oscillation at the resonant frequency. It is analyzed that why the resonance problem occurs in Vienna rectifier with the existing PWM methods. To solve these resonance problems, the proposed method injects a sinusoidal harmonic voltage into the sinusoidal reference voltage. The magnitude and phase of the injection voltage are determined by the power factor of the rectifier-side. Compared to other PWM methods, the proposed PWM method eliminates the possibility of resonant problems. Considering the operation characteristics of the proposed PWM method, this article suggests a design process for an LCL filter. The effectiveness and performance of the proposed PWM method and the design process for an LCL filter are verified by simulation and experiment. [ABSTRACT FROM AUTHOR]

Finite control set model predictive control (FCS-MPC) has been widely used in the control of grid-connected converters with the advantages of fast dynamics, multi-objective control, and easy implement. However, the conventional FCSMPC bears with variable switching frequency, high current ripple and computational burden. An improved current model predictive with the cost function-based modulation scheme (CFM-MPC) is proposed for a three-phase three-level VIENNA rectifier to improve the power quality. First, the mathematical model and voltage vector are given according to the principle of deadbeat control. Then, the voltage vector of different voltage vectors are selected according to the location of the voltage vector reference, and the switching action time of the selected are directly calculated by the inversely proportional with cost function value of the selected vectors. It remains the merits of both the conventional MPC and space vector pulse width modulation schemes to track the optimum voltage vector without increasing the computational burden. Finally, a comparative study with the proposed CFM-MPC and conventional FCS-MPC has been conducted to verify the superiority of the proposed scheme. The results show the proposed CFM-MPC has the advantages of lower power ripple, fixed switching frequency, lower total harmonic distortion and neutral point potential balance. [ABSTRACT FROM AUTHOR]

This article proposes a model predictive control (MPC) with the discrete space vector modulation (DSVM) to reduce input current ripple of three-level Vienna rectifier. The finite control set MPC (FCS-MPC) applied in power converters has variable switching frequency and needs high sampling frequency for better input current quality. With the proposed approach, more feasible vectors can be used to improve the input current's performance with the DSVM using the virtual vectors. The DSVM-MPC features fixed switching frequency and should implement large numbers of virtual vectors with the calculation burden. The improved DSVM-MPC is proposed to optimise the MPC algorithm by selecting the adjacent feasible vectors according to the reference voltage vector trajectory. The effectiveness of the proposed method is verified by the experimental results in a Vienna rectifier platform, which shows that the proposed method possesses better input current performance compared with the FCS-MPC method. [ABSTRACT FROM AUTHOR]