Search

This thesis presents the results of an investigation of factors which influence the geotechnical properties of frozen mine backfill (FMB). FMB has extensive application potential for mining in permafrost areas. The uniaxial compressive strength (UCS) of hardened backfill is often used to evaluate mine backfill stability. However, the deformation behaviour and stiffness of the FMB are also key design properties of interest. In this thesis, uniaxial compressive tests were conducted on FTB and FCPB samples. Information about the geotechnical properties of FMB is obtained. The effects of FMB mix components and vertical compression pressure on the geotechnical properties of FMB are discussed and summarized. An optimum total water content of 25%-35% is found in which the strength and the modulus of elasticity of the FTB are 1.4-3.2 MPa and 35-58 MPa, respectively. It is observed that a small amount (3-6%) of cement can significantly change the geotechnical properties of FTB.

The objective of this study is to understand the geochemical behaviour of arsenic in cemented paste backfills. This technique consists in transporting the tailings in the mine openings. Two types of backfills are prepared in the laboratory for this study. First, synthetic cemented paste backfills artificially spiked with arsenic are synthesized, using silica in replacement of the tailings. In parallel, other cemented paste backfill specimens are prepared with arsenic-rich tailings. In the two cases, various types of hydraulic binders are tested. Several types of investigations are conducted on the cemented paste backfill specimens. A mineralogical characterization is carried out with the help of specific tools. At the same time, cemented paste backfill samples are submitted to several complementary leaching tests, to assess the mobility/immobilization potential of arsenic in these matrices. Finally, geochemical modeling is implemented, based on the results of the two previous studies, in order to refine the understanding of the nature and stability of the arsenic compounds. The results show that arsenic is better immobilized in Portland cement and slag-based matrices, rather than in fly ash-based matrices. The variable leaching behaviour from a given matrix to another is due to different arsenic trapping mechanisms. Arsenic can precipitate and form several arsenic minerals, mainly calcium arsenates, but also various other secondary compounds, which are different from a matrix to another. Physical entrapment of the tailings grains by the cementitious minerals can also occur, by formation of a coating around the grains, limiting the oxidation and dissolution of arsenic-bearing sulfides (passivation). These mechanisms are involved in the stabilization/solidification of arsenic by cemented paste backfills., L’objectif de la thèse est de comprendre le comportement géochimique de l’arsenic dans les remblais miniers en pâte cimentés. Cette technique est employée depuis plusieurs années pour remblayer les galeries de mine exploitées à l’aide des rejets de concentrateurs. Pour cette étude, deux types de remblais sont élaborés en laboratoire : des échantillons de remblai minier en pâte synthétiques, fabriqués à partir de silice et enrichis artificiellement en arsenic, et des remblais miniers en pâte élaborés à partir de rejets miniers arséniés. Dans les deux cas, différents liants cimentaires sont testés. Plusieurs types d’investigations sont menés sur les échantillons de remblai en pâte cimentés. Une caractérisation minéralogique est effectuée à l’aide de divers outils. En parallèle, les échantillons de remblais sont soumis à différents tests de lixiviation complémentaires, afin d’évaluer la mobilité/rétention de l’arsenic dans ces matrices. Enfin, une modélisation géochimique est mise en œuvre à partir des résultats issus des deux études précédentes, afin d’affiner les connaissances sur la nature et la stabilité des composés arséniés dans les remblais étudiés. Les résultats obtenus indiquent que l’arsenic est mieux stabilisé dans les matrices à base de ciment Portland et de laitier de haut-fourneau que dans les remblais à base de cendres volantes. Le comportement à la lixiviation variable d’une matrice à l’autre s’explique par des spéciations et des mécanismes de piégeage de l’arsenic variés. L’arsenic peut précipiter sous forme de minéraux arséniés, principalement sous forme d’arséniates de calcium, mais aussi de divers autres composés secondaires variables d’une matrice à l’autre. Un piégeage physique des grains de rejets miniers arséniés par les hydrates cimentaires peut aussi avoir lieu, par formation d’un revêtement limitant l’oxydation des sulfures porteurs d’arsenic. Tous ces mécanismes interviennent dans la stabilisation/solidification de l’arsenic.

Gelfill (GF) is made of tailings, water, binder and chemical additives (Fillset, sodium silicate gel). The components of GF are combined and mixed on the surface and transported (by gravity and/or pumping) to the underground mine workings, where the GF can be used for both underground mine support and tailings storage. Thermal (T), hydraulic (H), and mechanical (M) properties are important performance criteria of GF. The understanding of these engineering properties and their evolution with time are still limited due to the fact that GF is a new cemented backfill material. In this thesis, the evolution of the thermal, hydraulic, mechanical, and microstructural properties of small GF samples are determined. Various binder contents of Portland cement type I (PCI) are used. The GF is cured for 3, 7, 28, 90, and 120 days. It is found that the thermal, hydraulic and mechanical properties are time-dependent or affected by the degree of binder hydration index. Furthermore, a relationship is found between the compressive strength and the saturated hydraulic conductivity of the GF samples. The unsaturated hydraulic properties of GF samples have also been investigated. The outcomes show that unsaturated hydraulic conductivity is influenced by the degree of binder hydration index and binder content, especially at low suction ranges. Simple functions are proposed to predict the evolution of air-entry values (AEVs), residual water content, and fitting parameters from the van Genuchten model with the degree of hydration index (α). Furthermore, two columns are built to simulate the coupled thermo-hydro-mechanical (THM) behaviour of GF under drained and undrained conditions. The obtained results from the GF columns are compared with the small samples. It is observed that the mechanical properties, hydraulic properties (suction and water content), and temperature development are strongly coupled. The magnitude of these THM coupling factors is affected by the size of the GF. The findings also show that the mechanical, hydraulic and thermal properties of the GF columns are different from samples cured in plastic moulds.

The objective of this study is to understand the geochemical behaviour of arsenic in cemented paste backfills. This technique consists in transporting the tailings in the mine openings. Two types of backfills are prepared in the laboratory for this study. First, synthetic cemented paste backfills artificially spiked with arsenic are synthesized, using silica in replacement of the tailings. In parallel, other cemented paste backfill specimens are prepared with arsenic-rich tailings. In the two cases, various types of hydraulic binders are tested. Several types of investigations are conducted on the cemented paste backfill specimens. A mineralogical characterization is carried out with the help of specific tools. At the same time, cemented paste backfill samples are submitted to several complementary leaching tests, to assess the mobility/immobilization potential of arsenic in these matrices. Finally, geochemical modeling is implemented, based on the results of the two previous studies, in order to refine the understanding of the nature and stability of the arsenic compounds. The results show that arsenic is better immobilized in Portland cement and slag-based matrices, rather than in fly ash-based matrices. The variable leaching behaviour from a given matrix to another is due to different arsenic trapping mechanisms. Arsenic can precipitate and form several arsenic minerals, mainly calcium arsenates, but also various other secondary compounds, which are different from a matrix to another. Physical entrapment of the tailings grains by the cementitious minerals can also occur, by formation of a coating around the grains, limiting the oxidation and dissolution of arsenic-bearing sulfides (passivation). These mechanisms are involved in the stabilization/solidification of arsenic by cemented paste backfills., L’objectif de la thèse est de comprendre le comportement géochimique de l’arsenic dans les remblais miniers en pâte cimentés. Cette technique est employée depuis plusieurs années pour remblayer les galeries de mine exploitées à l’aide des rejets de concentrateurs. Pour cette étude, deux types de remblais sont élaborés en laboratoire : des échantillons de remblai minier en pâte synthétiques, fabriqués à partir de silice et enrichis artificiellement en arsenic, et des remblais miniers en pâte élaborés à partir de rejets miniers arséniés. Dans les deux cas, différents liants cimentaires sont testés. Plusieurs types d’investigations sont menés sur les échantillons de remblai en pâte cimentés. Une caractérisation minéralogique est effectuée à l’aide de divers outils. En parallèle, les échantillons de remblais sont soumis à différents tests de lixiviation complémentaires, afin d’évaluer la mobilité/rétention de l’arsenic dans ces matrices. Enfin, une modélisation géochimique est mise en œuvre à partir des résultats issus des deux études précédentes, afin d’affiner les connaissances sur la nature et la stabilité des composés arséniés dans les remblais étudiés. Les résultats obtenus indiquent que l’arsenic est mieux stabilisé dans les matrices à base de ciment Portland et de laitier de haut-fourneau que dans les remblais à base de cendres volantes. Le comportement à la lixiviation variable d’une matrice à l’autre s’explique par des spéciations et des mécanismes de piégeage de l’arsenic variés. L’arsenic peut précipiter sous forme de minéraux arséniés, principalement sous forme d’arséniates de calcium, mais aussi de divers autres composés secondaires variables d’une matrice à l’autre. Un piégeage physique des grains de rejets miniers arséniés par les hydrates cimentaires peut aussi avoir lieu, par formation d’un revêtement limitant l’oxydation des sulfures porteurs d’arsenic. Tous ces mécanismes interviennent dans la stabilisation/solidification de l’arsenic.

Summarization: In this study two series of uniaxial compression and indirect tensile (Brazilian) tests, as well as a multi-stage triaxial compression test were performed in order to determine the mechanical properties and to develop a shear failure criterion for a particular Cemented Paste Backfill (CPB). CPB is used in underground mines for backfilling excavated stopes. This practice provides ground support to adjacent stopes, thereby permitting mining of the surrounding ore (i.e., increased ore recovery). It is a high-density, non-segregating, low-plasticity mixture of mine tailings, binder, and water which typically contains 70%–85% solids. The multistage triaxial test has been adopted as an alternative to a series of single-stage triaxial tests to determine engineering material parameters of rocks, whereas three single-stage triaxial tests are required to obtain a complete failure envelope, one multi-stage triaxial test may give the complete failure envelope. This paper mainly focuses on the experimental development of a shear failure criterion using just one multi-stage triaxial test of a CPB consisting of carbonate sand with grain size ≤ 250 μm instead of mine tailings, Portland cement as a binder and tap water. Presented on