Search

A fully self-contained in-vacuum device for measuring thin film stress in situ is presented. The stress was measured by measuring the curvature of a cantilever on which the thin film was deposited. For this, a dual beam laser deflectometer was used. All optics and electronics needed to perform the measurement are placed inside a vacuum-compatible vessel with the form factor of the substrate holders of the deposition system used. The stand-alone nature of the setup allows the vessel to be moved inside a deposition system independently of optical or electronic feedthroughs while measuring continuously. A Mo/Si multilayer structure was analyzed to evaluate the performance of the setup. A radius of curvature resolution of 270 km was achieved. This allows small details of the stress development to be resolved, such as the interlayer formation between the layers and the amorphous-to-crystalline transition of the molybdenum which occurs at around 2 nm. The setup communicates with an external computer via a Wi-Fi connection. This wireless connection allows remote control over the acquisition and the live feedback of the measured stress. In principle, the vessel can act as a general metrology platform and add measurement capabilities to deposition setups with no modification to the deposition system.

V/Sc multilayer is experimentally demonstrated for the first time as a high reflectance mirror for the soft X-ray water window region. It primarily works at above the Sc-L edge (λ = 3.11 nm) under near normal incidence while a second peak appears at above the V-L edge (λ = 2.42 nm) under grazing incidence. The V/Sc multilayer fabricated with a d-spacing of 1.59 nm and 30 bilayers has a smaller interface width (σ = 0.27 and 0.32 nm) than the conventional used Cr/Sc (σ = 0.28 and 0.47 nm). For V/Sc multilayer with 30 bilayers, the introduction of B 4 C barrier layers has little improvement on the interface structure. As the number of bilayers increasing to 400, the growth morphology and microstructure of the V/Sc layers evolves with slightly increased crystallization. Nevertheless, the surface roughness remains to be 0.25 nm. A maximum soft X-ray reflectance of 18.4% is measured at λ = 3.129 nm at 9° off-normal incidence using the 400-bilayers V/Sc multilayer. According to the fitted model, an s-polarization reflectance of 5.2% can also be expected at λ = 2.425 nm under 40° incidence. Based on the promising experimental results, further improvement of the reflectance can be achieved by using a more stable deposition system, exploring different interface engineering methods and so on.

We have modified and stabilized the ruthenium surface by depositing a self-assembled monolayer (SAM) of 1-hexadecanethiol on a polycrystalline ruthenium thin film. The growth mechanism, dynamics, and stability of these monolayers were studied. SAMs, deposited under ambient conditions, on piranha-cleaned and piranha + H 2 SO 4 cleaned substrates were compared to monolayers formed on H-radical-cleaned Ru surfaces. We found that alkanethiols on H-radical-cleaned Ru formed densely packed monolayers that remained stable when kept in a nitrogen atmosphere. X-ray photoelectron spectroscopy (XPS) shows a distinct sulfur peak (BE = 162.3 eV), corresponding to metal-sulfur bonding. When exposed to ambient conditions, the SAM decayed over a period of hours.

The adsorption and dissociation of carbon dioxide on a Ru(0001) single crystal surface was investigated by reflection-absorption infrared spectroscopy (RAIRS) and temperature-programmed desorption (TPD) spectroscopy for CO 2 adsorbed at 85 K. RAIRS spectroscopy shows that the adsorption of CO 2 on a Ru(0001) single crystal is partially dissociative, resulting in CO 2 and CO. The CO vibrational mode was also observed to split into two distinct modes, indicating two general populations of CO present at the surface. Furthermore, a time-dependent blue-shift is observed, which is characteristic of increasing CO surface coverage. TPD showed that coverages of up to 0.3 ML were obtained, and no evidence for chemisorption of oxygen on ruthenium was found.

The RAIRS spectra of water adsorbed on Ru(0001) at 85 K are recorded from 600 cm -1 to 4000 cm -1 . Measured at water coverages from 0.13 ML to 2.0 ML, the RAIRS spectra suggest that chemisorption of water on Ru(0001) depends on coverage. Water adsorbs on a clean Ru surface as chemisorbed ice-like clusters (likely through an O-Ru bond) up to 0.33 ML. Above this coverage, the chemisorbed layer saturates. Upon more exposure, water adsorbs as a liquid-like H-bonded layer without bonding to the Ru substrate. The chemisorbed water absorbs 7 times less IR per molecule than the liquid-like structure, which indicates that the orientation of the chemisorbed water is more parallel to the surface. Additionally, the influence of water-Ru bonding on H-bonding is reflected in the OH symmetric stretching mode. Under perturbation from water-Ru bonding, a large red shift (40 cm -1 ) in the free OH stretching frequency is observed in the chemisorbed clusters. By deconvoluting the main H-bonded OH stretching peak into five Gaussian sub-bands at 2945 ± 5 cm -1 , 3210 ± 5 cm -1 , 3300 ± 15 cm -1 , 3430 ± 5 cm -1 and 3570 ± 10 cm -1 , changes in the H-bonding network are rationalized in terms of H-bonding motifs. The donor-acceptor-acceptor motif is significant only in the chemisorbed clusters. On the other hand, the donor-acceptor motif dominates in the liquid-like structure, which increases the disorder present in the adlayer. Although chemisorption is suppressed above 0.33 ML, no structural changes in the ice-like clusters are observed up to multilayer coverage. Therefore, ice-like and liquid-like water coexist in a meta-stable state at 85 K.

We employ X-ray absorption near-edge spectroscopy at the boron K-edge and the phosphorus L 2,3 -edge to study the structural properties of cubic boron phosphide (c-BP) samples. The X-ray absorption spectra are modeled from first-principles within the density functional theory framework using the excited electron core-hole (XCH) approach. A simple structural model of a perfect c-BP crystal accurately reproduces the P L 2,3 -edge, however it fails to describe the broad and gradual onset of the B K-edge. Simulations of the spectroscopic signatures in boron 1s excitations of intrinsic point defects and the hexagonal BP crystal phase show that these additions to the structural model cannot reproduce the broad pre-edge of the experimental spectrum. Calculated formation enthalpies show that, during the growth of c-BP, it is possible that amorphous boron phases can be grown in conjunction with the desired boron phosphide crystalline phase. In combination with experimental and theoretically obtained X-ray absorption spectra of an amorphous boron structure, which have a similar broad absorption onset in the B K-edge spectrum as the cubic boron phosphide samples, we provide evidence for the presence of amorphous boron clusters in the synthesized c-BP samples.

Renewed interest has been witnessed in utilizing the piezoelectric response of PbZr 0.52 Ti 0.48 O 3 (PZT) films on glass substrates for applications such as adaptive optics. Accordingly, new methodologies are being explored to grow well-oriented PZT thin films to harvest a large piezoelectric response. However, thin film piezoelectric response is significantly reduced compared to intrinsic response due to substrate induced clamping, even when films are well-oriented. Here, a novel method is presented to grow preferentially (100)-oriented PZT films on glass substrates by utilizing crystalline nanosheets as seed layers. Furthermore, increasing the repetition frequency up to 20 Hz during pulsed laser deposition helps to tune the film microstructure to hierarchically ordered columns that leads to reduced clamping and enhanced piezoelectric response evidenced by transmission electron microscopy and analytical calculations. A large piezoelectric coefficient of 250 pm/V is observed in optimally tuned structure which is more than two times the highest reported piezoelectric response on glass. To confirm that the clamping compromises the piezoelectric response, denser films are deposited using a lower repetition frequency and a BiFeO 3 buffer layer resulting in significantly reduced piezoelectric responses. This paper demonstrates a novel method for PZT integration on glass substrates without compromising the large piezoelectric response.

We present the first experimental demonstration of a novel type of narrowband and wavelength-tunable multilayer transmission filter for the extreme ultraviolet (EUV) region. The operating principle of the filter is based on spatially overlapping the nodes of a standing wave field with the absorbing layers within the multilayer structure. For a wavelength with a matching node pattern, this increases the transmission as compared to neighboring wavelengths where anti-nodes overlap with the absorbing layers. Using Ni/Si multilayers where Ni provides strong absorption, we demonstrate the proper working of such anomalous transmission filter. The demonstration is carried out at the example of 13.5 nm wavelength and at normal incidence, providing a 0.27 nm-wide transmission peak. We also demonstrate wavelength tunability by operating the same Ni/Si filter at different wavelengths by varying the angle of incidence. As the multilayer filter is directly deposited on the active area of an EUV-sensitive photodiode, this provides an extremely compact device for easy spectral monitoring in the EUV. The transmission spectrum of the filter is modeled and found to be in good agreement with the experimental data. The agreement proves that such filters and compact monitoring devices can be straightforwardly designed and fabricated, as desired, also for other EUV wavelengths, bandwidths and angles of incidence, thereby showing a high potential for applications.

For photon energies of 1 - 5 keV, blazed gratings with multilayer coating are ideally suited for the suppression of stray and higher orders light in grating monochromators. We developed and characterized a blazed 2000 lines/mm grating coated with a 20 period Cr/C- multilayer. The multilayer d-spacing of 7.3 nm has been adapted to the line distance of 500 nm and the blaze angle of 0.84° in order to provide highest efficiency in the photon energy range between 1.5 keV and 3 keV. Efficiency of the multilayer grating as well as the reflectance of a witness multilayer which were coated simultaneously have been measured. An efficiency of 35% was measured at 2 keV while a maximum efficiency of 55% was achieved at 4 keV. In addition, a strong suppression of higher orders was observed which makes blazed multilayer gratings a favorable dispersing element also for the low X-ray energy range.

We report a hybrid thin-film deposition procedure to significantly enhance the reflectivity of La/B-based multilayer structures. This is of relevance for applications of multilayer optics at 6.7-nm wavelength and beyond. Such multilayers showed a reflectance of 64.1% at 6.65 nm measured at 1.5-degrees off-normal incidence at PTB (BESSY-II). This was achieved by a special scheme of La passivation. The La layer was nitridated to avoid formation of the optically unfavorable LaBx compound at the B-on-La interface. To avoid the also undesired BN formation at the La-on-B interface, a time-dosed nitridation at the initial stage was applied. This research revealed a good potential for further increase in the reflectivity of multilayer structures at 6.7 nm.

Here, we propose a comparison-free inspection technique to detect particle contamination on the reticle of extreme ultraviolet (EUV) lithography systems, based on the photoluminescence spectral characteristics of the contaminant particles and their elemental composition. We have analyzed the spectra from different particles found on reticles in EUV lithographic systems and have determined the minimum detectable particle size: 25 nm for organic particles and 100 nm for Al particles. Stainless steel coatings (50 nm thick and 50 × 50 μm(2) in area) exhibit detectable photoluminescence, and the estimated minimum detectable particle is 2 μm.

Wideband multilayers designed for various applications in hard X-ray to Extreme UV spectral regions are based on a layered system with layer thicknesses varying largely in depth. However, because the internal structure of a thin film depends on its thickness, this will result in multilayers in which material properties such as density, crystallinity, dielectric constant and effective thickness vary from layer to layer. This variation causes the fabricated multilayers to deviate from the model and negatively influences the reflectivity of the multilayers. In this work we solve this problem by developing designs of wideband multilayers with strongly reduced layer thickness variations in depth, without essential degradation of their optical characteristics.

We present state-of-the-art high resolution transmission gratings, applicable for spectroscopy in the vacuum ultraviolet (VUV) and the soft X-ray (SRX) wavelength range, fabricated with a novel process using ultraviolet based nano imprint lithography (UV-NIL). Free-standing, high-line-density gratings with up to 10,000 lines per mm and various space-to-period ratios were fabricated. An optical characterization of the gratings was carried out in the range from 17 to 34 nm wavelength using high-harmonic generation in a capillary waveguide filled with Ne, and around 13.5 nm wavelength (from 10 to 17 nm) using a Xenon discharge plasma.

A new scheme for wavefront correction in the extreme ultraviolet wavelength range is presented. The central feature of the scheme is the successful growth of crystalline piezoelectric thin films with the desired orientation on an amorphous glass substrate. The piezoelectric films show a high piezoelectric coefficient of 250 pm/V. Using wavefront calculations we show that the grown films would enable high-quality wavefront correction, based on a stroke of 25 nm, with voltages that are well below the electrical breakdown limit of the piezoelectric film.

We present a way to analyze the chemical composition of periodical multilayer structures using the simultaneous analysis of grazing incidence hard X-Ray reflectivity (GIXR) and normal incidence extreme ultraviolet reflectance (EUVR). This allows to combine the high sensitivity of GIXR data to layer and interface thicknesses with the sensitivity of EUVR to the layer densities and atomic compositions. This method was applied to the reconstruction of the layered structure of a LaN/B multilayer mirror with 3.5 nm periodicity. We have compared profiles obtained by simultaneous EUVR and GIXR and GIXR-only data analysis, both reconstructed profiles result in a similar description of the layered structure. However, the simultaneous analysis of both EUVR and GIXR by a single algorithm lead to a ∼ 2x increased accuracy of the reconstructed layered model, or a more narrow range of solutions, as compared to the GIXR analysis only. It also explains the inherent difficulty of accurately predicting EUV reflectivity from a GIXR-only analysis.

High spectral purity at longer wavelength side is demanded in many extreme ultraviolet (EUV) and soft X-ray (together also referred to as XUV) optical systems. It is usually obtained at the expense of a high loss of XUV efficiency. We proposed and developed a new method based on a periodic, tapered structure integrated with an EUV multilayer. The longer wavelength radiation is scattered/diffracted away by the tapered multilayer structure while the EUV light is reflected. The first proof-of-principle showed a broadband suppression from λ = 100-400 nm with an average factor of 14. Moreover, a high EUV reflectance of 64.7% was achieved, which corresponds to 94% of the efficiency of a regular EUV multilayer mirror.

We present the design of a novel collector mirror for laser produced plasma (LPP) light sources to be used in extreme ultraviolet (EUV) lithography. The design prevents undesired infrared (IR) drive laser light, reflected from the plasma, from reaching the exit of the light source. This results in a strong purification of the EUV light, while the reflected IR light becomes refocused into the plasma for enhancing the IR-to-EUV conversion. The dual advantage of EUV purification and conversion enhancement is achieved by incorporating an IR Fresnel zone plate pattern into the EUV reflective multilayer coating of the collector mirror. Calculations using Fresnel-Kirchhoff's diffraction theory for a typical collector design show that the IR light at the EUV exit is suppressed by four orders of magnitude. Simultaneously, 37% of the reflected IR light is refocused back the plasma.

A surface structured extreme ultraviolet multilayer mirror was developed showing full band suppression of UV (λ=100-400  nm) and simultaneously a high reflectance of EUV light (λ=13.5  nm). The surface structure consists of Si pyramids, which are substantially transparent for EUV but reflective for UV light. The reflected UV is filtered out by blazed diffraction, interference, and absorption. A first demonstration pyramid structure was fabricated on a multilayer by using a straightforward deposition technique. It shows an average suppression of 14 times over the whole UV range and an EUV reflectance of 56.2% at 13.5 nm. This robust scheme can be used as a spectral purity solution for all XUV sources that emit longer wavelength radiation as well.

We present theoretically derived design rules for an absorbing resonance antireflection coating for the spectral range of 100 - 400 nm, applied here on top of a molybdenum-silicon multilayer mirror (Mo/Si MLM) as commonly used in extreme ultraviolet lithography. The design rules for optimal suppression are found to be strongly dependent on the thickness and optical constants of the coating. For wavelengths below λ ∼ 230 nm, absorbing thin films can be used to generate an additional phase shift and complement the propagational phase shift, enabling full suppression already with film thicknesses far below the quarter-wave limit. Above λ ∼ 230 nm, minimal absorption (k < 0.2) is necessary for low reflectance and the minimum required layer thickness increases with increasing wavelength slowly converging towards the quarter-wave limit.As a proof of principle, SixCyNz thin films were deposited that exhibit optical constants close to the design rules for suppression around 285 nm. The thin films were deposited by electron beam co-deposition of silicon and carbon, with N+ ion implantation during growth and analyzed with variable angle spectroscopic ellipsometry to characterize the optical constants. We report a reduction of reflectance at λ = 285 nm, from 58% to 0.3% for a Mo/Si MLM coated with a 20 nm thin film of Si0.52C0.16N0.29.

In the first part of this article we experimentally show that contrast between the very thin layers of La and B enables close to theoretical reflectance. The reflectivity at 6.8 nm wavelength was measured from La/B multilayer mirrors with period thicknesses ranging from 3.5 to 7.2 nm at the appropriate angle for constructive interference. The difference between the measured reflectance and the reflectance calculated for a perfect multilayer structure decreases with increasing multilayer period. The reflectance of the multilayer with the largest period approaches the theoretical value, showing that the optical contrast between the very thin layers of these structures allows to experimentally access close to theoretical reflectance. In the second part of the article we discuss the structure of La/B and LaN/B multilayers. This set of multilayers is probed by hard X-rays (λ = 0.154 nm) and EUV radiation (λ = 6.8 nm). The structure is reconstructed based on a simultaneous fit of the grazing incidence hard X-ray reflectivity and the EUV reflectivity curves. The reflectivity analysis of the La/B and LaN/B multilayer mirrors shows that the lower reflectance of La/B mirrors compared to LaN/B mirrors can be explained by the presence of 5% of La atoms in the B layer and 63% of B in La layer. After multi-parametrical optimization of the LaN/B system, including the nitridation of La, the highest near normal incidence reflectivity of 57.3% at 6.6 nm wavelength has been measured from a multilayer mirror, containing 175 bi-layers. This is the highest value reported so far.

We report on the development of a hybrid mirror realized by integrating an EUV-reflecting multilayer coating with a lamellar grating substrate. This hybrid mirror acts as an efficient Bragg reflector for extreme ultraviolet (EUV) radiation at a given wavelength while simultaneously providing spectral-selective suppression of the specular reflectance for unwanted longer-wavelength radiation due to the grating phase-shift resonance. The test structures, designed to suppress infrared (IR) radiation, were fabricated by masked deposition of a Si grating substrate followed by coating of the grating with a Mo/Si multilayer. To give the proof of principle, we developed such a hybrid mirror for the specific case of reflecting 13.5 nm radiation while suppressing 10 μm light, resulting in 61% reflectance at the wavelength of 13.5 nm together with the 70 × suppression rate of the specular reflection at the wavelength of 10 μm, but the considered filtering principle can be used for a variety of applications that are based on utilization of broadband radiation sources.

An extended set of coupled wave equations were derived to describe non-idealized lamellar multilayer grating structures with properties as obtained with state-of-the-art fabrication techniques. These generalized equations can include all relevant effects describing the influence of passivation and contamination layers, non-rectangular lamel profiles and sidewall scalloping. The calculations showed that passivation and contamination plays an important role in that it may significantly reduce peak reflectivity. However, we also derived a condition for layer thicknesses having negligible effects. Slightly positive tapered lamel profiles are shown to further reduce the bandwidth as compared to a rectangular lamel profile, whereas negative tapers significantly increased the bandwidth. The influence of intriguing effects, such as the sidewall scalloping caused by Bosch Deep Reactive Ion Etching, are also modeled. We identified the signature of such scalloping as additional side peaks in the reflectivity spectrum and present parameters with which these can be effectively suppressed.

Amplitude-division beam splitters for XUV radiation sources have been developed and extensively characterized. Mo/Si multilayer coatings were deposited on 50 nm-thick SiN membranes. By changing the multilayer structure (periodicity, number of bilayers, etc.) the intensity of the reflected and transmitted beams were optimized for selected incident radiation parameters (wavelength, incident angle). The developed optical elements were characterized by means of XUV reflectometry and transmission measurements, atomic force microscopy and optical interferometry. Special attention was paid to the spatial homogeneity of the optical response and reflected beam wavefront distortions. Here the results of the characterization are presented and improvements required for advanced applications at XUV free-electron lasers are identified. A flatness as low as 4 nm r.m.s. on 3 × 3 mm beam splitters and 22 nm r.m.s. on 10 × 10 mm beam splitters has been obtained. The high-spatial-frequency surface roughness was about 0.7-1 nm r.m.s. The middle-spatial-frequency roughness was in the range 0.2-0.8 nm r.m.s. The reflection and transmission of the beam splitters were found to be very homogeneous, with a deviation of less than 2% across the full optical element.

We studied the structure and optical properties of B(4)C/Mo/Y/Si multilayer systems. Using extended x-ray absorption fine structure measurements at the Y and Mo K-edge, the structure of the subnanometer thick Y layer and the underlying Mo layer were analyzed. It was found that even a 0.2 nm thick Y layer significantly reduced silicon diffusion toward Mo, thus reducing Mo silicide formation. Hard x-ray reflectometry showed that the difference in average interface roughness of the B(4)C/Mo/Y/Si multilayer structure compared to Mo/Si and B(4)C/Mo/B(4)C/Si multilayer structures was negligible. Soft x-ray reflectometry showed optical improvement of B(4)C/Mo/Y/Si with respect to Mo/Si and B(4)C/Mo/B(4)C/Si multilayer structures.

The single shot damage thresholds of multilayer optics for high-intensity short-wavelength radiation sources are theoretically investigated, using a model developed on the basis of experimental data obtained at the FLASH and LCLS free electron lasers. We compare the radiation hardness of commonly used multilayer optics and propose new material combinations selected for a high damage threshold. Our study demonstrates that the damage thresholds of multilayer optics can vary over a large range of incidence fluences and can be as high as several hundreds of mJ/cm(2). This strongly suggests that multilayer mirrors are serious candidates for damage resistant optics. Especially, multilayer optics based on Li(2)O spacers are very promising for use in current and future short-wavelength radiation sources.

The spectral properties of La/B, La/B(4)C, and LaN/B, LaN/B(4)C multilayer mirrors have been investigated in the 6.5-6.9 nm wavelength range based on measured B and B(4)C optical constants. Experimentally it is verified to what extent measured and tabulated optical constants are applicable for simulations of the reflectivity of these short period multilayer mirrors. The measured maximum reflectance at various wavelength values around the boron-K absorption edge is compared to calculated values from model systems. The measured reflectance profiles of La/B and La/B(4)C show a maximum at a slightly larger wavelength than calculations would predict based on the measured B and B(4)C optical constants. This is explained by the influence of a formed boron-lanthanum compound on the wavelength where the multilayer shows maximum reflectance. The maximum reflectance profiles of LaN/B and LaN/B(4)C multilayers can be described accurately by using the same boron atomic scattering factors, indicating boron in the LaN/B(4)C multilayer to be in a similar chemical state as boron in the LaN/B multilayer. It also indicates that nitridation of the La layer in the multilayer prevents the formation of La-B compounds. We show that the optimal wavelength for boron based optics is about 6.65 nm and depends on the B chemical state. Finally, using the measured B optical constants we are able to calculate the spectral response of the multilayers, enabling the prediction of the optimal parameters for the above mentioned multilayers.

An extreme ultraviolet multilayer mirror with an integrated spectral filter for the IR range is presented and experimentally evaluated. The system consists of an IR-transparent B4C/Si multilayer stack which is used both as EUV-reflective coating and as a phase shift layer of the resonant IR antireflective (AR) coating. The AR coating is optimized in our particular case to suppress CO2 laser radiation at a wavelength of 10.6 μm, and a suppression of more than two orders of magnitude is demonstrated. The method allows high suppression over a large angular acceptance range, relevant for application in lithography systems.

We report on the mechanisms of hydrogen-induced blistering of multilayer coatings. Blister formation is a result of highly localized delamination occurring at the two outermost metal-on-silicon interfaces. The number, size, and type of blisters formed varied depending on the composition and ion energy of the incident flux. The results are explained in terms of the multilayer structure being simultaneously susceptible to blistering via two independent mechanisms. A high density of small blisters developed when relatively energetic (several 100 eV) ions were present. Independently, a hydrogenation process that was facilitated by the presence of a small flux of low energy ions (≤ 50 eV) induced a low density of large blisters.

We show that, under the right conditions, one can make highly accurate polarization-based measurements without knowing the absolute polarization state of the probing light field. It is shown that light, passed through a randomly varying birefringent material has a well-defined orbit on the Poincar sphere, which we term a generalized polarization state, that is preserved. Changes to the generalized polarization state can then be used in place of the absolute polarization states that make up the generalized state, to measure the change in polarization due to a sample under investigation. We illustrate the usefulness of this analysis approach by demonstrating fiber-based ellipsometry, where the polarization state of the probe light is unknown, and, yet, the ellipsometric angles of the investigated sample (Ψ and Δ) are obtained with an accuracy comparable to that of conventional ellipsometry instruments by measuring changes to the generalized polarization state.

A generic design and fabrication scheme of Mo/Si multilayer-grating phaseshift reflector systems is reported. Close to optimized extreme ultraviolet (EUV, λ=13.5 nm) reflectance values up to 64% are demonstrated, while the diffractive properties can be exploited in spectral filtering applications. The results can contribute to a wavelength-unspecific solution for the suppression of λ>100 nm out-of-band radiation in EUV lithography.

We have developed a multilayer mirror for extreme UV (EUV) radiation (13.5 nm), which has near-zero reflectance for IR line radiation (10.6 μm). The EUV reflecting multilayer is based on alternating B4C and Si layers. Substantial transparency of these materials with respect to the IR radiation allowed the integration of the multilayer coating in a resonant quarter-wave structure for 10.6 μm. Samples were manufactured using magnetron sputtering deposition technique and demonstrated suppression of the IR radiation by up to 3 orders of magnitude. The EUV peak reflectance amounts 45% at 13.5 nm, with a bandwidth at FWHM being 0.284 nm. Therefore such a mirror could replace conventional multilayer mirrors to suppress undesired spectral components in monochromatic imaging applications, including EUV photolithography.

We characterize the phase shift induced by reflection on a multilayer mirror in the extreme UV range (80-93 eV) using two techniques: one based on high order harmonic generation and attosecond metrology (reconstruction of attosecond beating by interference of two-photon transitions), and a second based on synchrotron radiation and measurements of standing waves (total electron yield). We find an excellent agreement between the results from the two measurements and a flat group delay shift (±40 as) over the main reflectivity peak of the mirror.

An analytic theory describing soft x-ray diffraction by Lamellar Multilayer Gratings (LMG) has been developed. The theory is derived from a coupled waves approach for LMGs operating in the single-order regime, where an incident plane wave can only excite a single diffraction order. The results from calculations based on these very simple analytic expressions are demonstrated to be in excellent agreement with those obtained using the rigorous coupled-waves approach. The conditions for maximum reflectivity and diffraction efficiency are deduced and discussed. A brief investigation into p-polarized radiation diffraction is also performed., (© 2011 Optical Society of America)

We investigated the damage mechanism of MoN/SiN multilayer XUV optics under two extreme conditions: thermal annealing and irradiation with single shot intense XUV pulses from the free-electron laser facility in Hamburg - FLASH. The damage was studied "post-mortem" by means of X-ray diffraction, interference-polarizing optical microscopy, atomic force microscopy, and scanning transmission electron microscopy. Although the timescale of the damage processes and the damage threshold temperatures were different (in the case of annealing it was the dissociation temperature of Mo2N and in the case of XUV irradiation it was the melting temperature of MoN) the main damage mechanism is very similar: molecular dissociation and the formation of N2, leading to bubbles inside the multilayer structure.

High resolution while maintaining high peak reflectivities can be achieved for Lamellar Multilayer Amplitude Gratings (LMAG) in the soft-x-ray (SXR) region. Using the coupled waves approach (CWA), it is derived that for small lamellar widths only the zeroth diffraction order needs to be considered for LMAG performance calculations, referred to as the single-order regime. In this regime, LMAG performance can be calculated by assuming a conventional multilayer mirror with decreased density, which significantly simplifies the calculations. Novel analytic criteria for the design of LMAGs are derived from the CWA and it is shown, for the first time, that the resolution of an LMAG operating in the single-order regime is not limited by absorption as in conventional multilayer mirrors. It is also shown that the peak reflectivity of an LMAG can then still be as high as that of a conventional multilayer mirror (MM). The performance of LMAGs operating in the single-order regime are thus only limited by technological factors.

The optical properties of a-periodic, depth-graded multilayer mirrors operating at 13.5 nm wavelength are investigated using different compositions and designs to provide a constant reflectivity over an essentially wider angular range than periodic multilayers. A reflectivity of up to about 60% is achieved in these calculation in the [0, 18 degrees] range of the angle of incidence for the structures without roughness. The effects of different physical and technological factors (interfacial roughness, natural interlayers, number of bi-layers, minimum layer thickness, inaccuracy of optical constants, and thickness errors) are discussed. The results from an experiment on the fabrication of a depth-graded Mo/Si multilayer mirror with a wide angular bandpass in the [0, 16 degrees] range are presented and analyzed.

We investigated single shot damage of Mo/Si multilayer coatings exposed to the intense fs XUV radiation at the Free-electron LASer facility in Hamburg - FLASH. The interaction process was studied in situ by XUV reflectometry, time resolved optical microscopy, and "post-mortem" by interference-polarizing optical microscopy (with Nomarski contrast), atomic force microscopy, and scanning transmission electron microcopy. An ultrafast molybdenum silicide formation due to enhanced atomic diffusion in melted silicon has been determined to be the key process in the damage mechanism. The influence of the energy diffusion on the damage process was estimated. The results are of significance for the design of multilayer optics for a new generation of pulsed (from atto- to nanosecond) XUV sources.

In this paper, we detect and characterize the carbon contamination layers that are formed during the illumination of extreme ultraviolet (EUV) multilayer mirrors. The EUV induced carbon layers were characterized ex situ using spectroscopic ellipsometry (SE) and laser generated surface acoustic waves (LG-SAW). We show that both LG-SAW and SE are very sensitive for measuring carbon layers, even in the presence of the highly heterogeneous structure of the multilayer. SE has better overall sensitivity, with a detection limit of 0.2 nm, while LG-SAW has an estimated detection limit of 2 nm. In addition, SE reveals that the optical properties of the EUV induced carbon contamination layer are consistent with the presence of a hydrogenated, polymeric like carbon. On the other hand, LG-SAW reveals that the EUV induced carbon contamination layer has a low Young's modulus (<100 GPa), which means that the layer is mechanically soft. We compare the limits of detection and quantification of the two techniques and discuss their prospective for monitoring carbon contamination build up on EUV optics.

The growth behavior of B(4)C interlayers deposited at the interfaces of Mo/Si multilayers was investigated using x-ray photoemission spectroscopy, x-ray reflectivity, and x-ray diffraction measurements. We report an asymmetry in the formation of B(4)C at the B(4)C-on-Mo interface compared to the B(4)C-on-Si interface. X-ray photoelectron spectroscopy (XPS) depth profiling shows that for B(4)C-on-Mo the formed stoichiometry is close to expectation (4:1 ratio), while for B(4)C-on-Si it is observed that carbon diffuses from the B(4)C interfaces into the multilayer, resulting in nonstochiometric growth (>4:1). As a result, there is a discrepancy in the optical response near 13.5 nm wavelength, where B(4)C-on-Mo behaves according to model simulations, while B(4)C-on-Si does not. The as-deposited off-stoichiometric B(4)C-on-Si interface also explains why these interfaces show poor barrier properties against temperature induced interdiffusion. We show that the stoichiometry of B(4)C at the Mo-Si interfaces is connected to the structure of the layers onto which B(4)C is grown. Because of enhanced diffusion into the amorphous Si surface, we suggest that deposited boron and carbon atoms form Si(X)B(Y) and Si(X)C(Y) compounds. The low formation enthalpy of Si(X)C(Y) ensures C depletion of any B(X)C(Y) interlayer. Only after a saturated interfacial layer is formed, does further deposition of boron and carbon atoms result in actual B(4)C formation. In contrast to the off-stoichiometric B(4)C growth on top of Si, B(4)C grown on top of Mo retains the correct stoichiometry because of the higher formation enthalpies for Mo(X)B(Y) and Mo(X)C(Y) formation and the limited diffusion depth into the (poly)-crystalline Mo surface.

We demonstrate, both theoretically and experimentally, that special spectral-purity-enhancing multilayer mirror systems can be designed and fabricated to substantially reduce the level of out-of-band radiation expected in an extreme ultraviolet lithographic tool. A first proof of principle of applying such spectral-purity-enhancement layers showed reduced out-of-band reflectance by a factor of five, while the in-band reflectance is only 4.5% (absolute) less than for a standard capped multilayer.

An experimental method is proposed for the creation of plasma optical waveguides at low electron densities. The method consists of creating a hollow neutral-hydrogen channel by means of fast local heating of a hydrogen volume by a needlelike electron beam, followed by laser ionization of the hydrogen to provide the plasma waveguide. Results of numerical simulations are presented which show that guiding with an axial electron density in the range of 10(17) cm-3 can be achieved with a matched spot size of 30 microm. Its application for laser wakefield acceleration of electrons is discussed. The method would enable guiding lengths up to 30 cm at maximal energies of accelerated electrons in the range 10-100 GeV.

A new method for the determination of the absolute brightness of pointlike soft-x-ray sources is proposed, and an example of its application is shown at a laser-plasma source for a wavelength band from 0.8 to ~ 1.7nm.