Search

Mechanically robust, non-toxic polymer fiber mats are promising materials for a range of biomedical applications; however, further research into enhancing polymer selection is needed. In this study, poly(allylamine) (PAH), an amine-containing polyelectrolyte, was successfully electrospun from aqueous solutions into continuous, cylindrical fibers with a mean diameter of 150 ± 41 nm. A one-step crosslinking method using glutaraldehyde provides insight into the chemical and morphological changes that result from altering the molar ratio of amine to aldehyde groups, whereas a two-step crosslinking method yielded chemically and mechanically robust mats. These results indicate PAH fibrous mats synthesized from aqueous solutions could potentially be applied in biomedical applications.

Re-engineering the support layers of membranes for forward and pressure retarded osmosis is critical for making these technologies commercially viable. Real-world applications of forward and pressure retarded osmosis, especially those involving natural and waste waters, will require membranes to withstand significant stresses. Therefore, structural changes to the support layer, which are necessary in minimizing internal concentration polarization, must not compromise its critical abilities to resist mechanical stress and provide a suitable surface for the interfacial polymerization of a robust and selective active layer. Electrospinning can provide nanofibers for support layers to potentially overcome the limitations of traditional membrane fabrication techniques in fulfilling these challenging design criteria. In this work, we present the fabrication and evaluation of thin-film composite membranes composed of electrospun polyethylene terephthalate nanofibers, a phase separation formed microporous polysulfone layer, and a polyamide selective layer formed by interfacial polymerization. These membranes have active and support layer transport properties that are suitable for engineered osmosis, with water permeability of 1.13 L m − 2 h − 1 bar − 1 (3.14 × 10 − 7 m s − 1 bar − 1 ), salt permeability of 0.23 L m − 2 h − 1 (6.4 × 10 − 8 m s − 1 ), and a structural parameter of 651 μm. Relevant and easily reproducible tests for membrane resistance to mechanical stress were performed. The use of electrospun fibers in the support layer enhanced membrane resistance to delamination at high cross-flow velocities because the 340 nm diameter electrospun fibers enmesh with the microporous polysulfone layer. A broader discussion of the most promising approaches for using electrospun materials to improve membranes for engineered osmosis is provided.

Quantifying the effect that nanofiber mat chemistry and hydrophilicity have on microorganism collection and inactivation is critical in biomedical applications. In this study, the collection and inactivation of Escherichia coli K12 was examined using cellulose nanofiber mats that were surface-functionalized using three polyelectrolytes: poly (acrylic acid) (PAA), chitosan (CS), and polydiallyldimethylammonium chloride (pDADMAC). The polyelectrolyte functionalized nanofiber mats retained the cylindrical morphology and average fiber diameter (~0.84 µm) of the underlying cellulose nanofibers. X-ray photoelectron spectroscopy (XPS) and contact angle measurements confirmed the presence of polycations or polyanions on the surface of the nanofiber mats. Both the control cellulose and pDADMAC-functionalized nanofiber mats exhibited a high collection of E. coli K12, which suggests that mat hydrophilicity may play a larger role than surface charge on cell collection. While the minimum concentration of polycations needed to inhibit E. coli K12 was 800 µg/mL for both CS and pDADMAC, once immobilized, pDADMAC-functionalized nanofiber mats exhibited a higher inactivation of E. coli K12, (~97%). Here, we demonstrate that the collection and inactivation of microorganisms by electrospun cellulose nanofiber mats can be tailored through a facile polyelectrolyte functionalization process.

In this review, we present a few of the many important objectives in the area of biomedical engineering that could open new pathways for nextgeneration biomaterials. We also provide examples of how materials for these goals can be created in an economically viable means through recent advances in high throughput production. These strategies highlight the potential for nanomanufacturing in a variety of areas of importance for human health and safety.

Biofilm-associated infections are one of the leading causes of death in the United States. Although infections may be treated with antibiotics, the overuse of antibiotics has led to the spread of antibiotic resistance. Many natural antimicrobial compounds derived from edible plants are safe for human use and target bacteria nonspecifically. Therefore, they may impair biofilm formation with less evolutionary pressure on pathogens. Here, we explore the use of two natural antimicrobial compounds, cinnamaldehyde (CA, from cinnamon) and carvacrol (CARV, from oregano), for biofilm prevention. We have fabricated and characterized films that incorporate CA and CARV into the biodegradable, FDA-approved polymer poly(lactic-co-glycolic acid), PLGA. The addition of CA and CARV to PLGA films not only adds antimicrobial activity but also changes the surface properties of the films, making them more hydrophilic and therefore more resistant to bacterial attachment. An addition of 0.1% CA to a PLGA film significantly impairs biofilm development by Staphylococcus aureus, and 0.1% CARV in PLGA significantly decreases biofilm formation by both Escherichia coli and S. aureus. Pseudomonas aeruginosa, which is less susceptible to CA and CARV, was not affected by the addition of 0.1% CA or CARV to the PLGA coatings; however, P. aeruginosa biofilm was significantly reduced by 1.0% CA. These results indicate that both CA and CARV could potentially be used in low concentrations as natural additives in polymer coatings for indwelling devices to delay colonization by bacteria.

For several reasons, the electrospinning of nanofibrous mats comprised purely of biopolymers, such as hyaluronic acid (HA) has been difficult to achieve. Most notably, due to its polyelectrolytic nature, very low polymer concentrations exhibit very high solution viscosities. Thus, it is challenging to obtain the critical chain entanglement concentration necessary for biopolymer electrospinning to ensue. While the successful electrospinning of HA fibers from a sodium hydroxide:dimethylformamide (NaOH:DMF) system has been reported, the diameter of these fibers was well above 100 nm. Moreover, questions regarding the degradation of HA within the solvent system arose. These factors supported our ongoing research into determining an improved solvent system. In this study, the use of a less basic (pH 11) aqueous ammonium hydroxide (NH4OH) solvent system, NH4OH:DMF, allowed for the fabrication of HA mats having an average fiber diameter of 39 ± 12 nm. Importantly, while using this solvent system, no degradation effects were observed and the continuous electrospinning of pure HA fibers was possible.

Cross-linked, non-woven fibrous membranes were successfully electrospun from carbon black–chitosan solutions. Morphology changes with increasing amounts of carbon black were analyzed by field emission scanning electron microscopy (FESEM). Chemical structure, conductance, and crystallinity of the fibrous membranes were investigated by Fourier transform infrared spectroscopy (FTIR), AC impedance spectroscopy, and X-ray diffraction (XRD), respectively. We hypothesize that even at 62.5 wt% loading of carbon black the particles are chelated and immobilized within the fibers by the natural polymer, chitosan. After cross-linking using glutaraldehyde vapor, all carbon black–chitosan membranes exhibited chemical stability in aqueous, acidic, and basic solutions for at least 20 days.

Polymer coatings featuring nonleaching antibacterial agents are needed to significantly reduce bacterial colonization and subsequent biofilm formation. Previously, single-walled carbon nanotubes (SWNTs) have been reported to be strong antimicrobial agents that kill microbes on contact. However, the antibacterial activity of freestanding polymer mats with a low weight percent of incorporated SWNTs has not been demonstrated. In this study, four different weight percents of well characterized, small diameter (0.8 nm) SWNTs were incorporated into electrospun polysulfone (PSf) mats. Electrospun PSf-SWNT mats were observed to be flexible and composed of continuous, cylindrical, and randomly oriented fibers. SEM micrographs revealed that SWNT ends were distributed along the longitudinal fiber axis. Loss of bacteria (Escherichia coli) viability was observed to directly correlate to increased SWNT incorporation within the mat, ranging from 18% for 0.1 wt % SWNTs to 76% for 1.0 wt % SWNTs. Time-dependent bacterial cytotoxicity studies indicated that the antimicrobial action of the PSf-SWNT mats occurs after a short contact time of 15 min or less. This study demonstrates the potential applicability of electrospun PSf-SWNT mats as antibacterial coatings.

From ship hulls to bandages, biological fouling is a ubiquitous problem that impacts a wide range of industries and requires complex engineered solutions. Eliciting materials to have antibacterial or antifouling properties describes two main approaches to delay biofouling by killing or repelling bacteria, respectively. In this review article, we discuss how electrospun nanofiber mats are blank canvases that can be tailored to have controlled interactions with biologics, which would improve the design of intelligent conformal coatings or freestanding meshes that deliver targeted antimicrobials or cause bacteria to slip off surfaces. Firstly, we will briefly discuss the established and emerging technologies for addressing biofouling through antibacterial and antifouling surface engineering, and then highlight the recent advances in incorporating these strategies into electrospun nanofibers. These strategies highlight the potential for engineering electrospun nanofibers to solicit specific microbial responses for human health and environmental applications.

Electrospinning is a complex process that requires numerous interacting physical instabilities. Assuming that a chosen polymer and solvent system can be spun, the chosen polymer exists in various states, which have variable crystallinities starting with the highest degree of crystallinity (when in bulk form) and ultimately being transformed into a non-woven mat. In an effort to better understand the effects that the electrospinning process has on the biopolymers chitin [practical grade (PG)] and chitosan [PG and medium molecular weight (MMW)], including post-production neutralization and cross-linking steps, field emission scanning electron microscopy (FESEM) and solubility studies were performed. An evaluation of diffraction peaks of the bulk, solution, and fibrous forms of chitin and chitosan were evaluated by X-ray diffraction (XRD) and determined that the formation of chitosan chains is influenced by the addition of solvent and cross-linking agent. This study is of importance since the crystallinity of chitin and chitosan directly relate to the ability of the biopolymers to chelate metals, and the chemical stability of non-woven mats aid in the creation of functional filtration membranes. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers

Material properties of the painted lady butterfly, Vanessa cardui Linnaeus were investigated using typical material science techniques. The examined butterflies were raised and hatched from the larvae stage and their chemical and crystalline structure evaluated and compared to that of crab shell (α-chitin) and squid pens from Notodarus sloanii and Loligo pealei (β-chitin). Fourier transmission infrared spectroscopy (FTIR) and X-ray diffraction (XRD) revealed that the painted lady butterflies are composed of α-chitin. Additionally, macro- and microstructure characterization of the chitins was conducted utilizing digital photography and field emission scanning electron microscopy (FESEM). This work demonstrates that common characterization techniques combined with simple sample preparation of biological materials can yield successful material characterization, which could aide the fabrication of biomimetic materials.

Electrospinning is a fabrication technique, which can be used to create nanofibrous non‐wovens from a variety of starting materials. The structure, chemical and mechanical stability, functionality, and other properties of the mats can be modified to match end applications. In this review, an introduction to biopolymers and the electrospinning process, as well as an overview of applications of nanofibrous biopolymer mats created by the electrospinning process will be discussed. Biopolymers will include polysaccharides (cellulose, chitin, chitosan, dextrose), proteins (collagen, gelatin, silk, etc.), DNA, as well as some biopolymer derivatives and composites.

Hydration is central to mitigating surface fouling by oil and microorganisms. Immobilization of hydrophilic polymers on surfaces promotes retention of water and a reduction of direct interactions with potential foulants. While conventional surface modification techniques are surface-specific, mussel-inspired adhesives based on dopamine effectively coat many types of surfaces and thus hold potential as a universal solution to surface modification. Here, we describe a facile, one-step surface modification strategy that affords hydrophilic, and underwater superoleophobic, coatings by the simultaneous deposition of polydopamine (PDA) with poly(methacryloyloxyethyl phosphorylcholine) (polyMPC). The resultant composite coating features enhanced hydrophilicity (i.e., water contact angle of ~10° in air) and antifouling performance relative to PDA coatings. PolyMPC affords control over coating thickness and surface roughness, and results in a nearly 10 fold reduction in Escherichia coli adhesion relative to unmodified glass. The substrate-independent nature of PDA coatings further promotes facile surface modification without tedious surface pretreatment, and offers a robust template for codepositing polyMPC to enhance biocompatibility, hydrophilicity and fouling resistance.

The fabrication and advanced function of large area biomimetic superhydrophobic surfaces (SHS) and slippery lubricant infused porous surfaces (SLIPS) are reported. The use of roll-to-roll nanoimprinting techniques enabled the continuous fabrication of SHS and SLIPS based on hierarchically wrinkled surfaces. Perfluoropolyether (PFPE) hybrid molds were used as flexible molds for roll-to-roll imprinting into a newly designed thiol-ene based photopolymer resin coated on flexible polyethylene terephthalate (PET) films. The patterned surfaces exhibit feasible superhydrophobicity with a water contact angle around 160° without any further surface modification. The SHS can be easily converted into SLIPS by roll-to-roll coating of a fluorinated lubricant, and these surfaces have outstanding repellence to a variety of liquids. Furthermore, both SHS and SLIPS display anti-biofouling properties when challenged with Escherichia coli K12 MG1655. The current report describes the transformation of artificial biomimetic structures from small, lab scale coupons to low cost, large area platforms.

Electrospinning hydrophilic nanofiber mats that deliver hydrophobic agents would enable the development of new therapeutic wound dressings. However, the correlation between precursor solution properties and nanofiber morphology for polymer solutions electrospun with or without hydrophobic oils has not yet been demonstrated. Here, cinnamaldehyde (CIN) and hydrocinnamic alcohol (H-CIN) were electrospun in chitosan (CS)/poly(ethylene oxide) (PEO) nanofiber mats as a function of CS molecular weight and degree of acetylation (DA). Viscosity stress sweeps determined how the oils affected solution viscosity and chain entanglement (Ce) concentration. Experimentally, the maximum polymer:oil mass ratio electrospun was 1:3 and 1:6 for CS/PEO:CIN and:H-CIN, respectively; a higher chitosan DA increased the incorporation of H-CIN only. The correlations determined for electrospinning plant-derived oils could potentially be applied to other hydrophobic molecules, thus broadening the delivery of therapeutics from electrospun nanofiber mats.

The current knowledge of bone marrow mechanics is limited to its viscous properties, neglecting the elastic contribution of the extracellular matrix. To get a more complete view of the mechanics of marrow, we characterized intact yellow porcine bone marrow using three different, but complementary techniques: rheology, indentation, and cavitation. Our analysis shows that bone marrow is elastic, and has a large amount of intra- and inter-sample heterogeneity, with an effective Young׳s modulus ranging from 0.25 to 24.7 kPa at physiological temperature. Each testing method was consistent across matched tissue samples, and each provided unique benefits depending on user needs. We recommend bulk rheology to capture the effects of temperature on tissue elasticity and moduli, indentation for quantifying local tissue heterogeneity, and cavitation rheology for mitigating destructive sample preparation. We anticipate the knowledge of bone marrow elastic properties for building in vitro models will elucidate mechanisms involved in disease progression and regenerative medicine.

In the present study, we have electrospun various grades of chitosan and cross-linked them using a novel method involving glutaraldehyde (GA) vapor, utilizing a Schiff base imine functionality. Chemical, structural, and mechanical analyses have been conducted by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and Kawabata microtensile testing, respectively. Additionally, the solubilities of the as-spun and cross-linked chitosan mats have been evaluated;solubility was greatly improved after cross-linking. SEM images displayed evidence that unfiltered low, medium, and high molecular weight chitosans, as well as practical-grade chitosan, can be electrospun into nanofibrous mats. The as-spun medium molecular weight chitosan nanofibers have a Young's modulus of 154.9 +/- 40.0 MPa and display a pseudo-yield point that arose due to the transition from the pulling of a fibrous mat with high cohesive strength to the sliding and elongation of fibers. As-spun mats were highly soluble in acidic and aqueous solutions. After cross-linking, the medium molecular weight fibers increased in diameter by an average of 161 nm, have a decreased Young's modulus of 150.8 +/- 43.6 MPa, and were insoluble in basic, acidic, and aqueous solutions. Though the extent to which GA penetrates into the chitosan fibers is currently unknown, it is evident that the cross-linking resulted in increased brittleness, a color change, and the restriction of fiber sliding that resulted in the loss of a pseudo-yield point.

Recently, bioactive chitosan films featuring naturally derived essential oils have attracted much attention due to their intrinsic antimicrobial properties and applicability to a broad range of applications. Previously, the ability to form thick (t > 100 µm), chitosan-essential oil films via solution casting has been demonstrated. However, the fabrication of well characterized ultrathin films (t

Chronic wounds continue to be a global healthcare concern. Thus, the development of new nanoparticle-based therapies that treat multiple symptoms of these "non-healing" wounds without encouraging antibiotic resistance is imperative. One potential solution is to use chitosan, a naturally antimicrobial polycation, which can spontaneously form polyelectrolyte complexes when mixed with a polyanion in appropriate aqueous conditions. The requirement of at least two different polymers opens up the opportunity for us to form chitosan complexes with an additional functional polyanion. In this study, chitosan:pectin (CS:Pec) nanoparticles were synthesized using an aqueous spontaneous ionic gelation method. Systematically, a number of parameters, polymer concentration, addition order, mass ratio, and solution pH, were explored and their effect on nanoparticle formation was determined. The size and surface charge of the particles were characterized, as well as their morphology using transmission electron microscopy. The effect of polymer concentration and addition order on the nanoparticles was found to be similar to that of other chitosan:polyanion complexes. The mass ratio was tuned to create nanoparticles with a chitosan shell and a controllable positive zeta potential. The particles were stable in a pH range from 3.5 to 6.0 and lost stability after 14 days of storage in aqueous media. Due to the high positive surface charge of the particles, the innate properties of the polysaccharides used, and the harmless disassociation of the polyelectrolytes, we suggest that the development of these CS:Pec nanoparticles offers great promise as a chronic wound healing platform.

Chitin is a nitrogen-rich polysaccharide that is abundant in crustaceans, mollusks, insects, and fungi and is the second most abundant organic material found in nature next to cellulose. Chitosan, the N-deacetylated derivative of chitin, is environmentally friendly, nontoxic, biodegradable, and antibacterial. Fibrous mats are typically used in industries for filter media, catalysis, and sensors. Decreasing fiber diameters within these mats causes many beneficial effects such as increased specific surface area to volume ratios. When the intrinsically beneficial effects of chitosan are combined with the enhanced properties of nanofibrous mats, applications arise in a wide range of fields, including medical, packaging, agricultural, and automotive. This is particularly important as innovative technologies that focus around bio-based materials are currently of high urgency, as they can decrease dependencies on fossil fuels. We have demonstrated that Schiff base cross-linked chitosan fibrous mats can be produced utilizing a one-step electrospinning process that is 25 times faster and, therefore, more economical than a previously reported two-step vapor-cross-linking method. These fibrous mats are insoluble in acidic, basic, and aqueous solutions for 72 h. Additionally, this improved production method results in a decreased average fiber diameter, which measures 128 +/- 40 nm. Chemical and structural analyses were conducted utilizing Fourier transform infrared spectroscopy, solubility studies, and scanning electron microscopy.

The incorporation of silver nanoparticles (AgNPs) into polymeric nanofibers has attracted a great deal of attention due to the strong antimicrobial activity that the resulting fibers exhibit. However, bactericidal efficacy of AgNP-coated electrospun fibrous mats has not yet been demonstrated. In this study, polysulfone (PSf) fibers were electrospun and surface-modified using an oxygen plasma treatment, which allowed for facile irreversible deposition of cationically charged polyethyleneimine (PEI)-AgNPs via electrostatic interactions. The PSf-AgNP mats were characterized for relative silver concentration as a function of plasma treatment time using ICP-MS and changes in contact angle. Plasma treatment of 60 s was the shortest time required for maximum loss of bacteria (Escherichia coli) viability. Time-dependent bacterial cytotoxicity studies indicate that the optimized PSf-AgNP mats exhibit a high level of inactivation against both gram negative bacteria, Escherichia coli, and gram positive bacteria, Bacillus anthracis and Staphylococcus aureus.

Nanotechnology has potential to offer solutions to problems facing the developing world. Here, we demonstrate the efficacy of an anodic multiwalled carbon nanotube (MWNT) microfilter toward the removal and inactivation of viruses (MS2) and bacteria (E. coli). In the absence of electrolysis, the MWNT filter is effective for complete removal of bacteria by sieving and multilog removal of viruses by depth-filtration. Concomitant electrolysis during filtration results in significantly increased inactivation of influent bacteria and viruses. At applied potentials of 2 and 3 V, the electrochemical MWNT filter reduced the number of bacteria and viruses in the effluent to below the limit of detection. Application of 2 and 3 V for 30 s postfiltration inactivated >75% of the sieved bacteria and >99.6% of the adsorbed viruses. Electrolyte concentration and composition had no correlation to electrochemical inactivation consistent with a direct oxidation mechanism at the MWNT filter surface. Potential dependent dye oxidation and E. coli morphological changes also support a direct oxidation mechanism. Advantages of the electrochemical MWNT filter for pathogen removal and inactivation and potential for point-of-use drinking water treatment are discussed.

Pressure retarded osmosis has the potential to produce renewable energy from natural salinity gradients. This work presents the fabrication of thin-film composite membranes customized for high performance in pressure retarded osmosis. We also present the development of a theoretical model to predict the water flux in pressure retarded osmosis, from which we can predict the power density that can be achieved by a membrane. The model is the first to incorporate external concentration polarization, a performance limiting phenomenon that becomes significant for high-performance membranes. The fabricated membranes consist of a selective polyamide layer formed by interfacial polymerization on top of a polysulfone support layer made by phase separation. The highly porous support layer (structural parameter S = 349 μm), which minimizes internal concentration polarization, allows the transport properties of the active layer to be customized to enhance PRO performance. It is shown that a hand-cast membrane that balances permeability and selectivity (A = 5.81 L m(-2) h(-1) bar(-1), B = 0.88 L m(-2) h(-1)) is projected to achieve the highest potential peak power density of 10.0 W/m(2) for a river water feed solution and seawater draw solution. The outstanding performance of this membrane is attributed to the high water permeability of the active layer, coupled with a moderate salt permeability and the ability of the support layer to suppress the undesirable accumulation of leaked salt in the porous support. Membranes with greater selectivity (i.e., lower salt permeability, B = 0.16 L m(-2) h(-1)) suffered from a lower water permeability (A = 1.74 L m(-2) h(-1) bar(-1)) and would yield a lower peak power density of 6.1 W/m(2), while membranes with a higher permeability and lower selectivity (A = 7.55 L m(-2) h(-1) bar(-1), B = 5.45 L m(-2) h(-1)) performed poorly due to severe reverse salt permeation, resulting in a similar projected peak power density of 6.1 W/m(2).

Recent studies show that osmotically driven membrane processes may be a viable technology for desalination, water and wastewater treatment, and power generation. However, the absence of a membrane designed for such processes is a significant obstacle hindering further advancements of this technology. This work presents the development of a high performance thin-film composite membrane for forward osmosis applications. The membrane consists of a selective polyamide active layer formed by interfacial polymerization on top of a polysulfone support layer fabricated by phase separation onto a thin (40 mum) polyester nonwoven fabric. By careful selection of the polysulfone casting solution (i.e., polymer concentration and solvent composition) and tailoring the casting process, we produced a support layer with a mix of finger-like and sponge-like morphologies that give significantly enhanced membrane performance. The structure and performance of the new thin-film composite forward osmosis membrane are compared with those of commercial membranes. Using a 1.5 M NaCl draw solution and a pure water feed, the fabricated membranes produced water fluxes exceeding 18 L m(2-)h(-1), while consistently maintaining observed salt rejection greater than 97%. The high water flux of the fabricated thin-film composite forward osmosis membranes was directly related to the thickness, porosity, tortuosity, and pore structure of the polysulfone support layer. Furthermore, membrane performance did not degrade after prolonged exposure to an ammonium bicarbonate draw solution.

The Greta oto, or the “glasswing butterfly”, is a member of the Ithomiini tribe. Although rare among lepidopteran, the G. oto’s wings are naturally transparent. To understand the material properties of natural transparency, the various structures on the surface of the wings, both the transparent and brown “veins” and wing parameter regions were studied using scanning electron microscopy (SEM), transmission electron microscopy (TEM), reflectance spectrometry, transmission spectrometry and scanning probe microscopy (SPM) in order to investigate their local structure, periodic character, and electromechanical response. Nanosized protuberances in a highly ordered array were found on the surface of the transparent part similar to that of the “corneal nipple array” found in other insects as an antireflective device.

We report on the nanopatterning of double-bond-terminated silane (5-hexenyltrichlorosilane, HTCS) molecules on titania (TiO2) using conductive atomic force microscopy (AFM). The influences of tip electrostatic potential and scanning velocity, relative humidity and of the repeated application of voltage on the topographic height, width, and hydrophilic and hydrophobic contrast of the resultant patterns were investigated. Tip voltage and tip velocity ( v) were applied between -10 Vor= V tipor= +10 V and 100 nm/sor= vor= 2 microm/s during the lithography step(s), respectively. Average height and Lateral Force Mode (LFM) images of patterns were obtained with different values of (-10 Vor= V tipor= -7 V) and v (100 nm/sor= vor= 2 microm/s). The average height of the patterns is seen to decrease for increasing v and decreasing V tip in both a single or repeated lithography step. No patterns were observed following a single or repeated lithography step for -5 Vor= V tipor= +10 V. This conductive lithography technique results in nanoscale physiochemical manipulations of the HTCS molecules that are manifested as controllable step heights ranging from approximately 1-15 nm possessing different chemistries on the patterned and unpatterned areas. The use of conductive-AFM nanolithography for altering and manipulating double-bond-terminated molecules on TiO2 surfaces suggests a range of applications, including selective immobilization and assembly of functionalized inorganic nanoparticles and biomolecules.