Search

In this review paper, several new approaches about the 3C-SiC growth are been presented. In fact, despite the long research activity on 3C-SiC, no devices with good electrical characteristics have been obtained due to the high defect density and high level of stress. To overcome these problems, two different approaches have been used in the last years. From one side, several compliance substrates have been used to try to reduce both the defects and stress, while from another side, the first bulk growth has been performed to try to improve the quality of this material with respect to the heteroepitaxial one. From all these studies, a new understanding of the material defects has been obtained, as well as regarding all the interactions between defects and several growth parameters. This new knowledge will be the basis to solve the main issue of the 3C-SiC growth and reach the goal to obtain a material with low defects and low stress that would allow for realizing devices with extremely interesting characteristics.

3C-SiC is an emerging material for MEMS systems thanks to its outstanding mechanical properties (high Young's modulus and low density) that allow the device to be operated for a given geometry at higher frequency. The mechanical properties of this material depend strongly on the material quality, the defect density, and the stress. For this reason, the use of SiC in Si-based microelectromechanical system (MEMS) fabrication techniques has been very limited. In this work, the complete characterization of Young's modulus and residual stress of monocrystalline 3C-SiC layers with different doping types grown on <100> and <111> oriented silicon substrates is reported, using a combination of resonance frequency of double clamped beams and strain gauge. In this way, both the residual stress and the residual strain can be measured independently, and Young's modulus can be obtained by Hooke's law. From these measurements, it has been observed that Young's modulus depends on the thickness of the layer, the orientation, the doping, and the stress. Very good values of Young's modulus were obtained in this work, even for very thin layers (thinner than 1 μm), and this can give the opportunity to realize very sensitive strain sensors.

The growth of 3C-SiC shows technological challenges, such as high supersaturation, a silicon-rich gas phase and a high vertical temperature gradient. We have developed a transfer method creating high-quality 3C-SiC-on-SiC (100) seeding stacks, suitable for use in sublimation "sandwich" epitaxy (SE). This work presents simulation data on the change of supersaturation and the temperature gradient between source and seed for the bulk growth. A series of growth runs on increased source to seed distances was characterized by XRD and Raman spectroscopy. Results show a decrease in quality in terms of single-crystallinity with a decrease in supersaturation. Morphology analysis of as-grown material indicates an increasing protrusion dimension with increasing thickness. This effect limits the achievable maximal thickness. Additional polytype inclusions were observed, which began to occur with low supersaturation (S ≤ 0.06) and prolonged growth (increase of carbon gas-species).

We report on the reproducible growth of two inch 3C-SiC crystals using the transfer of chemical vapor deposition (CVD)-grown (100) oriented epitaxial layers. Additional experiments, in which the diameter of the free-standing layers is increased, are presented, indicating the upscale potential of this process. The nucleation and growth of cubic silicon carbide is supported by XRD and Raman measurements. The rocking curve data yield a full-width-at-half-maximum (FWHM) between 138 to 140 arc sec for such grown material. Analysis of the inbuilt stress of the bulk-like material shows no indications of any residual stress., Competing Interests: The authors declare no conflict of interest.

Replacing GaAs by graphene to realize more practical quantum Hall resistance standards (QHRS), accurate to within 10(-9) in relative value, but operating at lower magnetic fields than 10 T, is an ongoing goal in metrology. To date, the required accuracy has been reported, only few times, in graphene grown on SiC by Si sublimation, under higher magnetic fields. Here, we report on a graphene device grown by chemical vapour deposition on SiC, which demonstrates such accuracies of the Hall resistance from 10 T up to 19 T at 1.4 K. This is explained by a quantum Hall effect with low dissipation, resulting from strongly localized bulk states at the magnetic length scale, over a wide magnetic field range. Our results show that graphene-based QHRS can replace their GaAs counterparts by operating in as-convenient cryomagnetic conditions, but over an extended magnetic field range. They rely on a promising hybrid and scalable growth method and a fabrication process achieving low-electron-density devices.